Huntsman Advanced Materials Americas Inc.
24-Hour Emergency Phone: 1-888-354-3323
MSDS No: 5774
Effective Date: 1/20/04 Material Safety Data Sheet
Health: 2
1. PRODUCT IDENTIFICATION 1
Flammability: 1
2 0
Reactivity: 0
Trade Name: Fastweld 10 Hardener
Personal Protection:
Chemical Family: Mercaptan
HMIS RATING
NFPA RATING
Intended Use or Product Type:
Adhesive Hardener.
2. COMPOSITION / INFORMATION ON INGREDIENTS
O CAS No. CHEMICAL IDENTITY EXPOSURE LIMITS CARCINOGEN
S STATUS
H ACGIH OSHA MFR. IARC NTP OSHA
A TWA STEL PEL STEL
* 90-72-2 Phenol, NE NE NE NE TLV 5 NR NR NR
2,4,6-tris[(dimethylamino)methyl]- ppm
Common 2,4,6-tris(Dimethylaminomethyl)ph
Name: enol
Confidential Mercaptan Terminated Liquid NE NE NE NE NE NR NR NR
Polymer
NE = Not Established NR = Not Reviewed * = OSHA Hazardous Ingredient
3. HAZARDS IDENTIFICATION
Emergency Overview: Causes skin and eye irritation. May cause allergic skin reaction.
Primary Route(s) of Entry: Dermal; heated product may produce inhalable vapors.
4. FIRST AID MEASURES
Ingestion: If conscious, give 2 - 4 glasses of water to drink. Do not induce vomiting. Call a physician.
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. Destroy contaminated
shoes.
Printed: 02/02/2004 Page 1 of 5
Fastweld 10 Hardener Huntsman Advanced Materials
Effective Date: 1/20/04 Americas Inc.
Inhalation: Remove to fresh air. Call a physician.
Eyes: Immediately flush eyes with water for at least 15 minutes. Call a physician.
Overexposure Effects: Causes skin and eye irritation. May cause allergic skin reaction.
Medical Conditions Aggravated by Exposure: Skin and eye conditions.
Additional Information: Referral to a physician is recommended if there is any question about the seriousness of any injury.
5. FIRE FIGHTING MEASURES
270癋 (132 癈)
Flash Point:
PMCC
Flash Point Method Used:
Not established
Flammable Limits in Air (Lower - % by volume):
Not established
Flammable Limits in Air (Upper - % by volume):
Fire Fighting Extinguishing Media: Carbon dioxide, dry chemical, foam, water.
Fire Fighting Equipment: Use self-contained breathing apparatus.
Fire and Explosion Hazards: Decomposition and combustion products may be toxic.
6. ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Remove spillage by absorbing in absorbent material.
7. HANDLING AND STORAGE
Signal Word: Warning!
Precautions: Can cause skin irritation, eye irritation, and allergic skin reaction. Avoid contact with eyes, skin, and clothing. Wash
thoroughly after handling.
Other Handling Information: Nuisance dust may be generated when sanding or sawing cured material.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Skin Protection: Wear impermeable gloves.
Respiratory Protection: Use NIOSH approved organic vapor cartridge respirator when vapor/mist exposure is likely.
Eye Protection: Wear splash-proof chemical goggles.
Engineering Controls: General mechanical and local exhaust in accordance with ACGIH recommendations.
9. PHYSICAL AND CHEMICAL PROPERTIES
Printed: 02/02/2004 Page 2 of 5
Fastweld 10 Hardener Huntsman Advanced Materials
Effective Date: 1/20/04 Americas Inc.
White
Color:
Typical Mercaptan
Odor:
Paste
Physical State:
Slight
Solubility in Water:
0.008 mm Hg at 25癈 (77 癋)
Vapor Pressure:
1.42 (water = 1)
Specific Gravity:
Not Determined
Boiling Point:
Not Determined
Evaporation Rate:
Not Determined
Vapor Density:
0 g/L
VOC:
Not Determined
pH:
Percent Volatile: Negligible.
10. STABILITY AND REACTIVITY
Conditions to Avoid: Excessive heat for prolonged periods of time.
Stability: Stable.
Incompatibility: Strong oxidizers, acids and bases.
Hazardous Decomposition Products: Combustion may form toxic materials, such as carbon dioxide, carbon monoxide.
Hazardous Polymerization: Will not occur.
11. TOXICOLOGICAL INFORMATION
Sensitization: Possible in susceptible individuals.
Skin Irritation: Irritant.
Eye Irritation: Irritant.
12. ECOLOGICAL INFORMATION
13. DISPOSAL CONSIDERATIONS
Waste Disposal Method: Consult qualified local or corporate personnel for method that will comply with local, state and federal
health and environmental regulations.
14. TRANSPORT INFORMATION
DOT: Bulk
Resin compounds, N.O.I.
Proper Shipping Name:
Printed: 02/02/2004 Page 3 of 5
Fastweld 10 Hardener Huntsman Advanced Materials
Effective Date: 1/20/04 Americas Inc.
Department of Transportation: Not regulated as a hazardous material by the U.S. Dept. of Transportation (DOT) 49 CFR 172.101
hazardous materials table.
15. REGULATORY INFORMATION
US Federal Regulations:
Occupational Safety and Health Act (OSHA): This Material Safety Data Sheet (MSDS) has been prepared in compliance with the
federal OSHA Hazard Communication Standard 29 CFR 1910.1200. This product is considered to be a hazardous chemical under
that standard.
Resource Conservation and Recovery Act (RCRA): Not a hazardous waste under RCRA (40 CFR 261).
SARA Title III: Section 313 Toxic Chemical List (TCL): This product does not contain any chemicals for routine annual toxic
chemical release reporting under Section 313 (40 CFR 372).
TSCA Section 8(b) - Inventory Status: Chemical components listed on TSCA Inventory.
TSCA Section 12(b) - Export Notification: This product does not contain any chemical(s) that are subject to a Section 12(b) export
notification.
State Regulations:
Pennsylvania Right-to-Know: The following is required composition information:
Chemical Name: Mercaptan Terminated Liquid Polymer
CAS Number: Confidential
Comment: Not on Pennsylvania Hazardous Substance List
Chemical Name: Sulfuric acid, barium salt (1:1)
Common Name: Barium Sulfate
CAS Number: 7727-43-7
Comment: Hazardous Substance
Chemical Name: Quarternary ammonium compounds, bis(hydrogenated tallow alkyl) dimethyl, chlorides, compounds with hectorite
Common Name: Bentonite clay
CAS Number: 71011-27-3
Comment: Not on Pennsylvania Hazardous Substance List
Chemical Name: Titanium dioxide
CAS Number: 13463-67-7
Comment: Hazardous Substance
Chemical Name: Phenol, 2,4,6-tris[(dimethylamino)methyl]-
Common Name: 2,4,6-tris(Dimethylaminomethyl)phenol
CAS Number: 90-72-2
Comment: Not on Pennsylvania Hazardous Substance List
Chemical Name: Silica
Common Name: Fumed Silica
CAS Number: 7631-86-9
Comment: Hazardous Substance
Printed: 02/02/2004 Page 4 of 5
Fastweld 10 Hardener Huntsman Advanced Materials
Effective Date: 1/20/04 Americas Inc.
16. OTHER INFORMATION
5774
MSDS No:
Kenneth L. Payne
Approved By:
E,H&S Manager
Title:
Disclaimer: The following supercedes Buyer's documents. SELLER MAKES NO REPRESENTATION OR WARRANTY,
EXPRESS OR IMPLIED, INCLUDING OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. No
statements herein are to be construed as inducements to infringe any relevant patent. Under no circumstances shall Seller be liable for
incidental, consequential or indirect damages for alleged negligence, breach of warranty, strict liability, tort or contract arising in
connection with the product(s). Buyer's sole remedy and Seller's sole liability for any claims shall be Buyer's purchase price. Data
and results are based on controlled or lab work and must be confirmed by Buyer by testing for its intended conditions of use. The
product(s) has not been tested for, and is therefore not recommended for, uses for which prolonged contact with mucous membranes,
abraded skin, or blood is intended; or for uses for which implantation within the human body is intended.
Printed: 02/02/2004 Page 5 of 5
|