MATERIAL SAFETY DATA SHEET
Date Revised: July 2005
Information on this form is furnished solely for the purpose of compliance with the Occupational Safety and Health Act and shall not be used for any other
purpose. T. Christy Enterprises, Inc. urges the customers receiving this Material Safety Data Sheet to study it carefully to become aware of the hazards, if any,
of the product involved. In the interest of safety, you should notify your employees, agents and contractors of the information on this sheet.
SECTION I
Transportation Emergencies:
MANUFACTURER'S NAME:
INFOTRAC: (800) 535-5053
T. Christy Enterprises, Inc.
ADDRESS: Medical Emergencies: (800) 451-8346
655 East Ball Road, Anaheim, CA 92805-5910
(714) 507-3300 FAX: (714)507-3310
CHEMICAL NAME and FAMILY TRADE NAME: Christy'sTM FastFixTM
Mixture Epoxy Repair Putty - Product Code: RH-FF4
FORMULA: Proprietary
SECTION II - HAZARDOUS INGREDIENTS
None of the ingredients below are listed as carcinogens by IARC, NTP or OSHA
CAS# % WT. ACGIH/TLV OSHA/PEL mm HG
Glycidyl ethers of bisphenol 25068-38-6 13.05 NE N.E. NE N.E. 0
A resins STEL = NE N.E. NE N.E.
Tri (dimethylaminomethyl) 90-72-2 1.37 NE N.E. NE N.E. 0
Phenol
**Title III Section 313 Supplier Notification; This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and
Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all MSDS'S that are copied and distributed for this material.
NOTES SPECIAL HAZARD DESIGNATIONS
D.O.T. Hazard Class: Not regulated HMIS HAZARD RATING
Hazard I.D. No.: N/A
HEALTH: 0-MINIMAL
D.O.T. Proper Shipping Name: Not regulated FLAMMABILITY:
1-SLIGHT
REACTIVITY:
2-MODERATE
Respirable crystalline silica (quartz) is classified as a proable carcinogen. The PROTECTIVE:
3-SERIOUS
crystalline silica present in this product is encapsulated in the epoxy resin and EQUIPMENT:
4-SEVERE
could only be liberated by sanding or abrading and then not as pure crystalline
silica. Appropriate precautions, however, should be taken, if the product is sanded
or abraded to preclude personnel from breathing the dust.
SECTION III - PHYSICAL DATA
APPEARANCE ODOR BOILING POINT ( ?F)
Putty N/A N/A
LIQUID DENSITY WEIGHT PER GALLON
SPECIFIC GRAVITY H2O = 1
16.20
Heavier than Water
N/A
EVAPORATION RATE (BUAC = 1)
VAPOR DENSITY SOLUBILITY IN WATER
0.0 x n-Butyl Acetate
Non-Volatile
VOC STATEMENT:
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLAMMABLE LIMITS LEL UEL
FLASH POINT
None N/A
(PERCENT BY VOLUME) N/A
FIRE EXTINGUISHING MEDIA
Water spray, foam, CO , dry chemicals.
2
SPECIAL FIRE FIGHTING PROCEDURES
None
UNUSUAL FIRE AND EXPLOSION HAZARDS
CO, aldehydes, acids, oxides of sulfur and nitrogen may be formed.
SECTION V - HEALTH HAZARD DATA
PRIMARY ROUTES
x Inhalation x Skin Contact x Eye Contact Ingestion
OF ENTRY:
EFFECT OF OVEREXPOSURE
ACUTE: Inhalation: None.
Skin Contact: Possible irritant and sensitizer.
Eye Contact: Possible irritant and sensitizer.
Ingestion: Irritation of intestinal tract.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Individuals with pre-existing diseases of the eyes, skin or respiratory system
may have increased susceptibility to the toxicity of excessive exposures.
EMERGENCY AND FIRST AID PROCEDURES
Inhalation: N/A
Eye Contact: Flush eyes with plenty of water for 15 minutes and call a doctor.
Skin Contact: Wash with soap and water.
Ingestion: Induce vomiting and call a doctor.
SECTION VI - REACTIVITY
CONDITIONS TO AVOID
STABILITY UNSTABLE
Keep away from heat, sparks, open flame and other sources of ignition which induce combustion or thermal
X
STABLE decomposition.
INCOMPATIBILITY
(MATERIALS TO AVOID) None
HAZARDOUS DECOMPOSITION PRODUCTS
CO, aldehydes, acids, oxides of sulfur and nitrogen
HAZARDOUS CONDITIONS TO AVOID
MAY OCCUR
None.
POLYMERIZATION WILL NOT OCCUR X
SECTION VII - SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Dispose of in normal manner; not a hazardous waste.
WASTE DISPOSAL METHOD
Dispose of material in accordance with applicable local, county, state and federal regualtions.
SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION
None required.
VENTILATION
General mechanical ventilation may be sufficient to keep product vapor and/or mist concentrations within specified TLV ranges.
Local exhaust - only if heated above 100?F (38?C).
PROTECTIVE GLOVES EYE PROTECTION
Safety glasses
Polyethylene gloves for prolonged use.
OTHER PROTECTIVE EQUIPMENT AND HYGENIC PRACTICES
None
SECTION IX - SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING - Avoid eye contact and excessive skin contact.
OTHER PRECAUTIONS -Wash with soap and water immediately after use. If sanding cured putty or substrates, wear eye
protection and dust mask.
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this
data or the results to be obtained from the use thereof.
|