MATERIAL SAFETY DATA SHEET
Part A--Clear Page 1 of 8
FT330 is a two component, solvent based epoxy coating that exhibits excellent characteristics for abrasion resis-
tance, chemical resistance and substrate penetration. This product is suitable as a primer for high build coatings
and urethane or as a stand alone coating.
I. IDENTIFICATION
Manufacturer Phone: 1.800.831.5600
Trade Name: FT330 Solvent Based Epoxy Primer--Part A Clear
Product Type: Solvent based epoxy primer
DOT Shipping Name: Flammable liquid N.O.S., 3, UN1993, pg. III.
HMIS Codes: Health=2* Flammability=3 Reactivity=0 P (specific hazards)=G
Emergency Phone:
II. HAZARDOUS INGREDIENTS
INGREDIENTS: CAS # ACGIH TLV OSHA STEL OSHA PEL VAPOR PRESSURE
SOLID EPOXY RESIN 25036-25-3 None None None NA
*XYLENE 1330-20-7 100 p.p.m. 150 p.p.m. 100 p.p.m. 5.1 @ 68癋
FLUROALIPHATIC POLYMERIC Unknown None None None NA
ESTERS (LESS THAN 0.3%)
PROPRIETARY NON HAZARD- Unknown None None None NA
OUS ADDITIVES
*Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372. ACGIH STEL=150 p.p.m. for
Xylene.
III. PHYSICAL DATA
Boiling Point: 279癋.
Vapor Density: NA
Specific Gravity (H2O=1): 1.0
Solubility of Water: Negligible
Evaporation Rate: NA
Appearance and Odor: Pale yellow liquid w/solvent odor
IV. FIRE AND EXPLOSION HAZARD DATA
Flashpoint: 77?F
Lower/Upper Explosive
Limit: NA
Extinguishing Media: Foam, alcohol foam, carbon dioxide, dry chemical, water fog
Special Firefighting
Procedures: Do not enter confined area without full bunker gear including a positive pressure NIOSH approved self-
contained breathing apparatus. Presence of solvents in product may require grounding.
UNUSUAL FIRE AND EXPLOSION HAZARDS: If fire occurs, solvents may produce excessive pressure. Sealed drums may rupture and ignite.
All five gallon plus containers should be grounded before transferring material. Vapors are heavier than air and
may travel along the ground and ignite by any source of ignition. Never use a cutting or welding torch near con-
tainers (even empty).
V. HEALTH AND SAFETY
Effects of Overexposure:
Eyes: Can cause severe irritation, redness, tearing or blurred vision.
Skin: May cause irritation and dermatitis.
Inhalation Can cause nausea, and respiratory irritation, dizziness, weakness, fatigue, headache and possible un-
consciousness.
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, diarrhea and aspiration of material into the lungs.
Can cause chemical pneumonitis which can be fatal.
Part A Clear
Material Safety Data Sheet Page 2 of 8
(Continued from page 1)
Chronic Exposure: Epoxy resins can cause sensitization by exposure through contact or high concentrations of vapor.
Over exposure to this material can cause cardiac abnormalities, anemia, liver abnormalities, kidney dam-
age or even eye damage.
Medical Conditions Prone to Aggravation by Exposure: Allergic response or respiratory conditions
Emergency and First Aid Procedures:
Eyes: Flush immediately with water for at least fifteen minutes, consult a physician.
Skin: Wash with soap and water. Will not normally cause more than irritation. Remove contaminated clothing
immediately.
Inhalation: If affected by vapors or spray mist, remove to fresh air. Administer oxygen if necessary.
Ingestion: Do not induce vomiting. Keep person warm, consult a physician immediately.
Carcinogenicity: NTP: No. IARC monographs: No. OHSA regulated: No.
VI. REACTIVITY DATA
Conditions to Avoid: Excessive heat, open flames, static discharge.
Hazardous Decomposition
Byproducts: May form toxic chemicals, carbon dioxide, carbon monoxide, and various hydrocarbons.
Hazardous Polymerization: Will not occur.
Incompatibility: Avoid amine curing agents in uncontrolled amounts and strong oxidizing agents.
Stability: Stable.
VII. SPILL OR LEAK PROCEDURES
Wear respirator and protective clothing, shut off the source of the leak. Remove excess with vacuum truck and take up the remainder with an
absorbent such as clay and place in disposal containers. Flush area with water to remove residue.
Waste Disposal Method: Dispose of waste in a waste disposal site in accordance with Federal, State and local laws.
VIII. SAFE HANDLING AND USE INFORMATION
Respiratory Protection: If PEL or TLV is exceeded, use NIOSH/MSHA Respirator TC230 or equivalent. Follow OSHA 29CFR
PART 1910.94. Engineering or administrative measures should be taken to reduce the risk and expo-
sure.
Ventilation: Provide sufficient mechanical and/or local exhaust ventilation to keep exposure below PEL or TLV.
Protective Gloves: Neoprene or rubber.
Eye Protection: Safety glasses with side shields, splash goggles.
Other Protective Equipment: To prevent repeated or prolonged contact, wear impervious clothing and boots. Use protective cream if
skin contact is likely.
Hygienic Practices: Wash hands before eating or smoking. Do not consume food or beverage while using this product.
IX. SPECIAL PRECAUTIONS
Precautions to be taken in handling and storing: Store away from heat, sparks, and flame. Keep containers tightly closed. Do not reuse
container. Empty container may retain hazardous residue. Keep away from heat, sparks and flame. Do not cut, puncture or weld on or near
container. Prevent breathing vapor or spray mist.
Other Precautions: Avoid all skin contact. Avoid breathing vapors generated from the material. Contaminated leather articles cannot be
cleaned and must be discarded if contaminated with this product. Wash all contaminated clothing prior to reuse. Wear appropriate safety equip-
ment and respirator at all times when ventilation is not sufficient to control vapors.
SAFETY STATEMENT
The information presented is believed to be accurate, but is not warranted to be whether originating from manufacturer or not. Recipients are
advised to confirm in advance, that the information is current, applicable, and relative to their individual circumstance.
Version Date: 10/22/02
MATERIAL SAFETY DATA SHEET
Part B--Clear Page 3 of 8
FT330 is a two component solvent based epoxy coating that exhibits excellent characteristics for abrasion resis-
tance, chemical resistance and substrate penetration. This product is suitable as a primer for high build coatings
and urethane or as a stand alone coating.
I. IDENTIFICATION
Manufacturer Phone: 1.800.831.5600
Trade Name: FT330 Solvent Based Epoxy Primer--Part B Clear
Product Type: Solvent based epoxy primer
DOT Shipping Name: Flammable liquid N.O.S., 3, UN1993, pg. III.
HMIS Codes: Health=2* Flammability=3 Reactivity=0 P (specific hazards)=G
Emergency Telephone No:
II. HAZARDOUS INGREDIENTS
INGREDIENTS: CAS # ACGIH TLV OSHA STEL OSHA PEL VAPOR PRESSURE
*XYLENE 1330-20-7 100 p.p.m. 150 p.p.m. 100 p.p.m. 5.1 @ 68癋
TRIETHYLENE TETRAMINE 112-24-3 None None None NA
DIMER/TOFA, REACTION 68082-29-1 None None None NA
PRODIUCTS WITH TETA
DIMETHYLAMINOEMETHYL- 25338-55-0 None None None NA
PHENOL
TRIS-2, 4, 6- 90-72-2 None None None 0.0 @ 70癋
DIMETHYLAMINOMETHYLPHE-
NOL
*BUTANOL NORMAL 71-36-3 50 p.p.m. None 50 p.p.m. 4.4 @ 68癋
BENZYL ALCOHOL 100-51-6 None None None 1.0 @ 136癋
*Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372. Xylene ACGIH STEL=150 p.p.m.
Butanol OSHA TWA (skin) =50 p.p.m. ACGIH TWA (skin) =50 p.p.m. Follow CWA 311(B)(2)(A) 40 CFR 116, 117; CWA 304 (A)(1) 45FR 79318;
TSCA 8(d) 40 CFR 716 47 FR 387 guidelines.
III. PHYSICAL DATA
Boiling Range: 200癋-401?F
Vapor Density: NA
Specific Gravity (H20=1): 0.9
Solubility In Water: Negligible
Evaporation Rate: NA
Appearance and Odor: Low viscosity liquid with solvent odor.
IV. FIRE AND EXPLOSION HAZARD DATA
Flashpoint: 79?F
Lower Explosive Limit: 1.4%
Upper Explosive Limit: 11.2%
Extinguishing Media: Foam, alcohol foam, carbon dioxide, dry chemical, or water fog.
Special Fire Fighting Procedures: Do not enter confined area without full bunker gear including, a positive pressure NIOSH approved self
contained breathing apparatus. Presence of solvents in product may require grounding.
UNUSUAL FIRE AND EXPLOSION HAZARDS: If fire occurs, solvents may produce excessive pressure. Sealed drums may rupture and ignite.
Vapors are heavier than air and may travel along the ground and ignite by any source of ignition. Never
use a cutting or welding torch near containers even when empty. All five gallon plus containers should
be grounded before transferring material.
Part B Clear
Material Safety Data Sheet Page 4 of 8
(Continued from page 3)
V. HEALTH AND SAFETY
Effects of Overexposure:
Eyes: Can cause severe irritation, redness, tearing or blurred vision.
Skin: Can cause irritation, and dermatitis. Not likely to be absorbed in toxic amounts but control measures
should be taken to eliminate contact with this product.
Inhalation: Can cause nausea, and respiratory irritation, dizziness, weakness, fatigue, nausea, headache and possi-
ble unconsciousness.
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, diarrhea. Aspiration of material into the lungs,
can cause chemical pneumontitis which can be fatal.
Chronic Exposure: Amine resins can cause sensitization by exposure through contact or high concentrations of vapor.
Overexposure to this material can cause cardiac abnormalities, anemia, liver abnormalities, kidney dam-
age or even eye damage.
Medical Conditions Prone to Aggravation by Exposure: Allergic response or respiratory conditions
Emergency and First Aid Procedures:
Eyes: Flush immediately with water for fifteen minutes, consult a physician.
Skin: Wash with soap and water. Will not normally cause more than irritation. Remove contaminated clothing
immediately.
Inhalation: If affected by vapors or spray mist, remove to fresh air. Administer oxygen if necessary.
Ingestion: Do not induce vomiting. Keep person warm, consult a physician.
Carcinogenicity: NTP: No. IARC monographs: No. OHSA regulated: No.
VI. REACTIVITY DATA
Conditions to Avoid: Excessive heat, open flames, and static discharge.
Hazardous Decomposition
Byproducts: May form toxic chemicals, Carbon dioxide, carbon monoxide, an various hydrocarbons, etc.
Hazardous Polymerization: Will not occur.
Incompatibility: Avoid epoxy curing agents in uncontrolled amounts and strong oxidizing agents.
Stability: Stable.
VII. SPILL OR LEAK PROCEDURES
Wear respirator and protective clothing. Shut off the source of the leak. Remove excess with vacuum truck and take up the remainder with an
absorbent such as clay and place in disposal containers. Flush area with water to remove residue.
Waste Disposal Method: Dispose of waste in a waste disposal site in accordance with Federal, State and local laws.
VIII. SAFE HANDLING AND USE INFORMATION
Respiratory Protection: If PEL or TLV is exceeded, use NIOSH/MSHA Respirator TC230 or equivalent, follow OSHA 29CFR
PART 1910.94. Engineering or administrative measures should be taken to reduce the risk and expo-
sure.
Ventilation: Provide sufficient mechanical and/or local exhaust ventilation to maintain exposure below PEL or TLV.
Protective Gloves: Neoprene or rubber gloves.
Eye Protection: Safety glasses with side shields, splash goggles.
Other Protective Equipment: Wear impervious clothing and boots. Use protective cream if skin contact is likely.
Hygienic Practices: Wash hands before eating or smoking. Do not consume food or beverage while using this product.
IX. SPECIAL PRECAUTIONS
Precautions to be Taken in Handling and Storing: Store away from heat, sparks and flame. Keep containers tightly closed. Do not reuse
container. Empty containers may contain hazardous residue. Keep away from heat, sparks and flame. Do not cut, puncture or weld on or near
container. Prevent breathing vapor or spray mist.
Other Precautions: Avoid all skin contact. Avoid breathing vapors generated from the material. Observe conditions of good general hygiene
and safe working practices. Contaminated leather articles cannot be cleaned and must be discarded if contaminated with this product. Wash all
contaminated clothing prior to reuse. Wear appropriate safety equipment and respirator at all times when ventilation is not sufficient to control
vapors.
SAFETY STATEMENT
The information presented is believed to be accurate, but is not warranted to be whether originating from manufacturer or not. Recipients are
advised to confirm in advance, that the information is current, applicable, and relative to their individual circumstance.
Version Date: 10/22/02
MATERIAL SAFETY DATA SHEET
Part A--Pigmented Page 5 of 8
FT330 is a two component solvent based epoxy coating that exhibits excellent characteristics for abrasion resis-
tance, chemical resistance and substrate penetration. This product is suitable as a primer for high build coatings
and urethane or as a stand alone coating.
I. IDENTIFICATION
Manufacturer Phone: 1.800.831.5600
Trade Name: FT 331-338 Solvent Based Epoxy Primer--Part A Pigmented
Product Type: Solvent based epoxy primer
DOT Shipping Name:
HMIS Codes: Health=2* Flammability=3 Reactivity=0 P (specific hazards)=G
Emergency Phone:
II. HAZARDOUS INGREDIENTS
INGREDIENTS: CAS # ACGIH TLV OSHA STEL OSHA PEL VAPOR PRESSURE
SOLID EPOXY RESIN 25036-25-3 None None None NA
*XYLENE 1330-20-7 100 p.p.m. 150 p.p.m. 100 p.p.m. 5.1 @ 68癋
PROPYLENE GLYCOL MONO- 107-98-2 100 p.p.m. 150 p.p.m. 100 p.p.m. 10.9 @ 77癋
METHYL ETHER
*Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372. ACGIH STEL =150 p.p.m. for
Xylene.
III. PHYSICAL DATA
Boiling Range: 243?279?br>
F- F
Vapor Density: NA
Specific Gravity (H2O=1): 1.0
Solubility in Water: Negligible
Evaporation Rate: NA
Appearance and Odor: Pale yellow liquid with solvent odor.
IV. FIRE AND EXPLOSION HAZARD DATA
Flashpoint: 75?F
Lower Explosive Limit: NA
Upper Explosive Limit: NA
Extinguishing Media: Foam, alcohol foam, carbon dioxide, dry chemical or water fog.
Special Firefighting Procedures: Do not enter confined area without full bunker gear including a positive pressure NIOSH approved self-
contained breathing apparatus. Presence of solvents in product may require grounding.
UNUSUAL FIRE AND EXPLOSION HAZARDS: If fire occurs, solvents may produce excessive pressure. Sealed drums may rupture and ignite.
Vapors are heavier than air and may travel along the ground and ignite by any source of ignition. Never use a
cutting or welding torch near containers even if empty. All five gallon plus containers should be grounded before
transferring material.
V. HEALTH AND SAFETY
Effects of Overexposure:
Eyes: Can cause severe irritation, redness, tearing or blurred vision.
Skin: May cause irritation and dermititis.
Inhalation: Can cause nausea, and respiratory irritation, dizziness, weakness, fatigue, headache and possible un-
consciousness.
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, diarrhea and aspiration of material into the lungs.
Can cause chemical pheumontitis which can be fatal.
Carcinogenicity: NTP: No. IARC Monographs: No. OHSA regulated: No.
Chronic Exposure: Epoxy resins can cause sensitization by exposure through contact or high concentrations of vapor.
Overexposure to this material can cause cardiac abnormalities, anemia, liver abnormalities, kidney dam-
age or even eye damage.
Medical Conditions Prone to Aggravation by Exposure: Allergic response or respiratory conditions.
Part A Pigmented
Material Safety Data Sheet Page 6 of 8
(Continued from page 5)
Emergency and First Aid Procedures:
Eyes: Flush immediately with water for fifteen minutes, consult a physician.
Skin Wash with soap and water. Will not normally cause more than irritation. Remove contaminated cloth-
ing immediately.
Inhalation: If affected by vapors or spray mist, remove to fresh air.. Administer oxygen if necessary.
Ingestion: DO NOT INDUCE VOMITING. Keep person warm, consult a physician immediately.
VI. REACTIVITY DATA
Conditions to Avoid: Excessive heat, open flames and static discharge.
Hazardous Decomposition
Byproducts: May form toxic chemicals, carbon dioxide, carbon monoxide, and various hydrocarbons.
Hazardous Polymerization: Will not occur
Incompatibility: Avoid amine curing agents in uncontrolled amounts and strong oxidizing agents.
Stability: Stable.
VII. SPILL OR LEAK PROCEDURES
Wear respirator and protective clothing, shut off the source at the leak. Remove excess with vacuum truck and take up the remainder with an
absorbent such as clay and place in disposal containers. Flush area with water to remove residue.
Waste Disposal Method: Dispose of waste in a waste disposal site in accordance with Federal, State and local laws.
VIII. SAFE HANDLING AND USE INFORMATION
Respiratory Protection: If PEL or TLV is exceeded, use NIOSH/MSHA respirator TC230 or equivalent. Follow OSHA 29CFR
Part 1910.94. Engineering or administrative measures should be taken to reduce the risk of exposure.
Ventilation: Provide sufficient mechanical and/or local exhaust ventilation to maintain exposure PEL or TLV.
Protective Gloves: Neoprene or rubber.
Eye Protection: Safety glasses with side shields, splash goggles.
Other Protective Equipment: To prevent repeated or prolonged contact, wear impervious clothing and boots. Use protective cream
if skin contact is likely.
Hygienic Practices: Wash hands before eating or smoking. Do not consume food or beverage while using this product.
IX. SPECIAL PRECAUTIONS
Precautions to be taken in handling and storing: Store in a cool dry place. Seal all partially used containers. Wash with soap and water
before eating, drinking smoking or using toilet facilities. Mixed materials contain the hazards of the components, therefore, read the MSDS of
all components prior to using material. Properly label all containers.
Other Precautions: Avoid skin contact. Avoid breathing vapors generated from the material. Observe conditions of good general hygiene and
safe working practices. Contaminated leather articles can not be cleaned and must be discarded if contaminated. Wash all other clothing prior
to reuse.
SAFETY STATEMENT
The information presented is believed to be accurate, but is not warranted to be whether originating from manufacturer or not. Recipients are
advised to confirm in advance, that the information is current, applicable, and relative to their individual circumstance.
Version Date: 10/22/02
MATERIAL SAFETY DATA SHEET
Part B--Pigmented Page 7 of 8
FT330 is a two component solvent based epoxy coating that exhibits excellent characteristics for abrasion resis-
tance, chemical resistance and substrate penetration. This product is suitable as a primer for high build coatings
and urethane or as a stand alone coating.
I. IDENTIFICATION
Manufacturer Phone: 1.800.831.5600
Trade Name: FT331-FT338 Solvent Based Epoxy Primer--Part B Pigmented
Product Type: Solvent based epoxy primer.
DOT Shipping Name:
HMIS Codes: Health=2* Flammability=3 Reactivity=0 P (specific hazards)=G
Emergency Phone:
II. HAZARDOUS INGREDIENTS
INGREDIENTS: CAS # ACGIH TLV OSHA STEL OSHA PEL VAPOR PRESSURE
*XYLENE 21% 1330-20-7 100 p.p.m. 150 p.p.m. 100 p.p.m. 5.1 @ 68癋
TRIETHYLENE TETRAMINE 112-24-3 None None None NA
DIMER/TOFA, REACTION 68082-29-1 None None None NA
PRODIUCTS WITH TETA
DIMETHYLAMINOEMETHYL- 25338-55-0 None None None NA
PHENOL
PIGMENT . Non hazardous in liquid form 10 mg/m? 5 mg/m? 10 mg/m? NA
AROMATIC PETROLEUM 64742-95-6 100 p.p.m. None 100 p.p.m. NA
DISTILLATES
TRIS-2, 4, 6- 90-72-2 None None None 0.0 @ 70癋
DIMETHYLAMINOMETHYLPHE-
NOL
*BUTANOL NORMAL 2% 71-36-3 50 p.p.m. None 50 p.p.m. 4.4 @ 68癋
PROPYLENE GLYCOL MONO- 108-65-6 None None None 3.7 @ 68癋
METHYL ETHER ACETATE
Non hazardous in liquid form 3 mg/m?br>
FILLER None 20 mppcf NA
Non hazardous in liquid form 20 mg/m?br>
EXTENDER 20 mg/m? 20 mg/m? NA
COPPER PHTHALOCYANINE 147-14-8 None None None NA
CARBON BLACK 1333-86-4 3.4 p.p.m. None 3.5 p.p.m. NA
*Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372. (ACGIH STEL = 150 p.p.m. for
Xylene)(Butanol: OSHA CEILING = 50 p.p.m., TWA-skin = 50 p.p.m. ACGIH TWA skin =50 p.p.m.) Follow TSCA 8(d) 40 CFR 47 FR 387:
RCRA 40 CFR 261; CWA 311 (b)(2)(a) 40 CFR 116, 117 guidelines.
III. PHYSICAL DATA
Boiling Range: 200癋-279?F.
Vapor Density: NA
Specific Gravity (H2O=1): 1.4
Solubility in Water: Negligible
Evaporation Rate: NA
Appearance and Odor: Low viscosity liquid in varying colors, solvent odor.
Part B Pigmented
Material Safety Data Sheet Page 8 of 8
IV. FIRE AND EXPLOSION HAZARD DATA
Flashpoint: 79?F
Extinguishing Media: Foam, alcohol foam, carbon dioxide, dry chemical, or water fog.
Special Firefighting Procedures: Do not enter confined area without full bunker gear including a positive pressure NIOSH approved self con-
tained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: If fire occurs, solvents may produce excessive pressure. Sealed drums may rupture and ignite.
Vapors are heavier than air and may travel along the ground and ignite by any sources of ignition. Never use
a cutting or welding torch near containers even if empty. All five gallon plus containers should be grounded
before transferring material.
V. HEALTH AND SAFETY
Effects of Overexposure:
Eyes: Can cause severe irritation, redness, tearing or blurred vision.
Skin: Can cause irritation, and dermatitis. Not likely to be absorbed in toxic amounts, but measures should be
taken to avoid all contact with this material.
Inhalation: Can cause nausea, and respiratory irritation, dizziness, weakness, fatigue, headache and possible uncon-
sciousness.
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, diarrhea and aspiration of material into the lungs. Can
cause chemical pheumontitis which can be fatal.
Carcinogenicity: NTP: No. IARC monographs: No. OHSA regulated: No.
Chronic Exposure: Amine resins can cause sensitization by exposure through contact or high concentrations of vapor. Over
exposure to this material can cause cardiac abnormalities, anemia, liver abnormalities, kidney damage or
even eye damage.
Medical Conditions Prone to Aggravation by Exposure: Allergic response or respiratory conditions.
Emergency and First Aid Procedures:
Eyes: Flush immediately with water for fifteen minutes, consult a physician.
Skin: Wash with soap and water. Will not normally cause more than irritation. Remove contaminated clothing
immediately.
Inhalation: If affected by vapors of spray mist, remove to fresh air. Administer oxygen if necessary.
Ingestion: DO NOT INDUCE VOMITING. Keep person warm, consult a physician.
VI. REACTIVITY DATA
Conditions to Avoid: Excessive heat, open flames and static discharge.
Hazardous Decomposition
Products: May form toxic chemicals, carbon dioxide, carbon monoxide, and various hydrocarbons.
Hazardous Polymerization: Will not occur.
Incompatibility: Avoid epoxy curing agents in uncontrolled amounts and strong oxidizing agents.
Stability: Stable
VII. SPILL OR LEAK PROCEDURES
Wear respirator and protective clothing, shut off the source at the leak. Remove excess with vacuum truck and take up the remainder with an
absorbent such as clay and place in disposal containers. Flush area with water to remove residue.
Waste Disposal Method: Dispose of waste in a waste disposal site in accordance with Federal, State and local laws.
VIII. SAFE HANDLING AND USE INFORMATION
Respiratory Protection: If PEL or TLV is exceeded, use NIOSH/MSHA respirator TC230 or equivalent.. Follow OSHA 29CFR PART
1910.94.
Ventilation: Provide sufficient mechanical and/or local exhaust ventilation to keep exposure below PEL or TLV
Protective Gloves: Neoprene or rubber.
Eye Protection: Safety glasses with side shields, splash goggles.
Other Protective Equipment: To prevent repeated or prolonged contact, wear impervious clothing an boots.
Hygienic Practices: Wash hands before eating or smoking. Do not consume food or beverage while using this product
IX. SPECIAL PRECAUTIONS
Precautions to be Taken in
Handling and Storing: Store away from heat, sparks and flame. Keep containers tightly closed.
Other Precautions: Do not reuse container. Empty containers may contain hazardous residue. Keep away from heat, sparks
and flame. Do not cut, puncture or weld on or near container. Prevent breathing of vapor or spray mist.
SAFETY STATEMENT
The information presented is believed to be accurate, but is not warranted to be whether originating from manufacturer or not. Recipients are
advised to confirm in advance, that the information is current, applicable, and relative to their individual circumstance.
Version Date: 10/22/02
|