MATERIAL SAFETY DATA SHEET
Page: 1
PERMA-CLEAN 100 EPOXY
5/21/2009
PRODUCT NAME: PERMA-CLEAN 100 EPOXY HMIS CODES: H F R P
PRODUCT CODE: A-4165 11E
SECTION I - MANUFACTURERS IDENTIFICATION
MANUFACTURER'S NAME: INDURON PROTECTIVE COATINGS, INC.
ADDRESS: 3333 RICHARD ARRINGTON Jr BLVD, N.
BIRMINGHAM, ALABAMA 35234
EMERGENCY PHONE: (205) 324-9584 INFORMATION PHONE: (205) 324-9584
DATE PRINTED: 5/21/2009 NAME OF PREPARER: John Anspach
SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONANTS CAS NUMBER mm Hg @ TEMP PERCENT
---------------------------------------------------------------------------------------------------------------------------------
DIGLYCIDYL ETHER OF BISPHENYL A 25068-38-6 N/A n/a 40 - 45%
NONE ESTABLISHED
! TITANIUM DIOXIDE 13463-67-7 N/A 20 - 25%
TLV/TWA=10 MG/M3 TOTAL DUST OR 5 MG/M3 (NUISANCE DUST)
REACTIVE DILUENT .11 68 F 10 - 15%
NONE ESTABLISHED
! MICROCRYSTALLINE SILICA 98.5-99.0% 14808-60-7 N/A 9.07
PEL-TLV/TWA=0.1 MG/M3 (RESPIRABLE DUST)
! OXIDE GLASS 65997-17-3 N/A 5 - 10%
ACGIH TLV NOT ESTABLISHED
OSHA PEL 5 MG/M3 RESPIRABLE
CARBON (RESPIRABLE FRACTION <5% SIO2) N/A N/A N/A < 5%
TLV= 2.4 MG/M3 (RESPIRABLE CARBON)
* INDICATES TOXIC CHEMICAL(S) SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III OF 40
CFR 372.
! NOTE: PIGMENTS DO NOT NORMALLY POSE A DUST HAZARD IN COATINGS.
Warning: Detectable amounts of chemicals known to the State of California to cause cancer and/or birth defects or
reproductive harm may be present in this product.
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
BOILING RANGE: 484 - 491 DENSITY: 10.962 lb/gl
MATERIAL SAFETY DATA SHEET
Page: 2
PERMA-CLEAN 100 EPOXY
5/21/2009
VAPOR DENSITY: HEAVIER THAN AIR.
EVAPORATION RATE: SLOWER THAN DIETHYL ETHER.
COATING VOC (Water Excluded): 0.0 lb/gl,0 g/l
SOLUBILITY IN WATER: INSOLUBLE.
APPEARANCE AND ODOR:
Opaque, viscous liquid. Aromatic Hydrocarbon solvent odors.
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 262 F METHOD USED: PMCC
FLAMMABLE LIMITS IN AIR BY VOLUME-LOWER: N/A UPPER: N/A
EXTINGUISHING MEDIA:
CARBON DIOXIDE, FOAM, DRY CHEMICAL, WATER SPRAY.
SPECIAL FIREFIGHTING PROCEDURES:
USE SELF CONTAINED BREATHING APPARATUS. WATER SHOULD BE USED AS A FOG ONLY, TO
KEEP CONTAINERS COOL IN ORDER TO MINIMIZE PRESSURE BUILDUP AND EXPLOSION.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
THIS MATERIAL WILL NOT SUSTAIN COMBUSTION UNLESS PREHEATED. IF CONTAINER IS NOT
PROPERLY COOLED, IT MAY EXPLODE IN THE HEAT OF A FIRE.
SECTION V - REACTIVITY DATA
STABILITY: STABLE UNDER NORMAL CONDITIONS OF STORAGE AND HANDLING.
CONDITIONS TO AVOID:
AVOID HEAT, SPARKS, FLAME AND OTHER POSSIBLE IGNITION SOURCES.
INCOMPATIBILITY (MATERIALS TO AVOID):
AVOID CONTACT WITH STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS, AND
STRONG MINERAL AND ORGANIC BASES, EXPECIALLY PRIMARY AND SECONDARY ALIPHATIC
AMINES. REACTIONS WITH SOME CURING AGENTS MAY PRODUCE CONSIDERABLE HEAT. RUN-A-
WAY REACTIONS MAY CHAR AND DECOMPOSE THE PRODUCT, GENERATING UNIDENTIFIED FUMES
AND VAPORS WHICH MAY BE TOXIC.
HAZARDOUS DECOMPOSITION BYPRODUCTS:
CARBON MONOXIDE, ALDEHYDES AND ACIDS AND OTHER ORGANIC COMPOUNDS MAY BE FORMED
DURING COMBUSTION.
HAZARDOUS POLYMERIZATION:
WILL NOT OCCUR.
MATERIAL SAFETY DATA SHEET
Page: 3
PERMA-CLEAN 100 EPOXY
5/21/2009
SECTION VI - HEALTH HAZARD DATA
SKIN CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
THIS PRODUCT MAY BE MODERATELY IRRITATING TO THE SKIN.
EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
THIS MATERIAL MAY CAUSE EYE IRRITATION. DIRECT CONTACT WITH THE LIQUID, VAPORS
OR AEROSOL MAY CAUSE STINGING, TEARING AND REDNESS.
SENSITIZATION:
POTENTIAL SKIN SENSITIZER.
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
BREATHING HIGH CONCENTRATIONS OF AEROSOLS OF THIS MATERIAL MAY CAUSE IRRITATION
OF THE NOSE, THROAT AND RESPIRATORY TRACT. DUST FROM THIS MATERIAL MAY CONTAIN
TRACE AMOUNTS OF CRYSTALLINE SILICA. FREQUENT INHALATION OF HIGH CONCENTRATIONS
OF DRY DUST GENERATED BY SANDING, CUTTING, BLASTING OR GRINDING THIS MATERIAL
OVER A LONG PERIOD OF TIME MAY CAUSE CANCER. RESPIRATORY SYMPTOMS ASSOCIATED
WITH PRE-EXISTING LUNG DISORDERS (E.G., ASTHMA-LIKE CONDITIONS) MAY BE
AGGRAVATED BY EXPOSURE TO DUST AND AEROSOLS OF THIS MATERIAL.
ORAL INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
WHILE THIS MATERIAL HAS A LOW DEGREE OF TOXICITY, INGESTION OF EXCESSIVE
QUANTITIES MAY CAUSE IRRITATION OF THE DIGESTIVE TRACT.
EFFECTS OF OVEREXPOSURE:
INHALATION:
DIZZINESS, BREATHING DIFFICULTY, HEADACHES, LOSS OF COORDINATION.
EYE CONTACT:
MODERATE IRRITATION, TEARING, REDNESS, AND BLURRED VISION.
SKIN CONTACT:
CAN CAUSE MODERATE IRRITATION AND DERMATITIS.
INGESTION:
MAY CAUSE IRRITATION OF THE DIGESTIVE TRACT.
CARCINOGENICITY: NTP?YES IARC MONOGAPHS?YES
NOTE: DUST FROM THIS MATERIAL MAY CONTAIN TRACE AMOUNTS OF CRYSTALLINE SILICA.
PERSONS IN THE IMMEDIATE VICINITY OF SANDING, CUTTING, BLASTING AND
GRINDING OPERATIONS ON THE DRY FILM SHOULD WEAR RESPIRATORY PROTECTION.
REFER TO THE RESPIRATORY PROTECTION SECTION OF THIS DOCUMENT.
OSHA REGULATED?YES.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
ALLERGY, ECZEMA, ASTHMA, OTHER SKIN CONDITIONS.
EMERGENCY AND FIRST AID PROCEDURES:
EYE CONTACT:
MATERIAL SAFETY DATA SHEET
Page: 4
PERMA-CLEAN 100 EPOXY
5/21/2009
IRRIGATE WITH FLOWING WATER IMMEDIATELY AND CONTINUOUSLY FOR 15 MINUTES HOLDING
EYELIDS OPEN. CONSULT MEDICAL PERSONNEL.
SKIN CONTACT:
IMMEDIATELY REMOVE CONTAMINATED CLOTHING AND REMOVE EXCESS FROM SKIN. WASH OFF
WITH SOAP AND FLOWING WATER OR SHOWER. WASH CLOTHING BEFORE REUSE.
CONTAMINATED LEATHER ARTICLES, INCLUDING SHOES, CANNOT BE DECONTAMINATED
AND SHOULD BE DISCARDED. IF SKIN IRRITATION OCCURS, SEE A PHYSICIAN.
INGESTION:
DO NOT INDUCE VOMITING. CALL A PHYSICIAN AND/OR TRANSPORT TO A MEDICAL FACILITY
IMMEDIATELY.
INHALATION OVEREXPOSURE:
IF RESPIRATORY SYMPTOMS DEVELOP, MOVE VICTIM AWAY FROM SOURCE OF EXPOSURE AND
INTO FRESH AIR. IF SYMPTOMS PERSIST, SEEK MEDICAL ATTENTION. IF VICTIM IS
NOT BREATHING, IMMEDIATELY BEGIN ARTIFICIAL RESPIRATION. IF BREATHING
DIFFICULTIES DEVELOP, OXYGEN SHOULD BE ADMINISTERED BY QUALIFIED PERSONNEL.
GET IMMEDIATE MEDICAL ATTENTION.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
REMOVE ALL SOURCES OF IGNITION. PROVIDE EXPLOSION PROOF VENTILATION. DIKE
SPILL AREA AND TAKE UP ON ABSORBENT MATERIAL. SHOVEL WITH NON-SPARKING TOOLS
INTO CLOSABLE CONTAINER FOR DISPOSAL. WEAR PROTECTIVE EQUIPMENT SPECIFIED
BELOW. THOROUGHLY FLUSH CONTAMINATED AREA WITH WATER.
WASTE DISPOSAL METHOD:
DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
KEEP AWAY FROM HEAT, SPARKS AND OPEN FLAME. AVOID CONTACT WITH EYES, SKIN AND
CLOTHING. AVOID BREATHING VAPOR, MIST OR SPRAY. USE ONLY WITH GOOD
VENTILATION. WASH AFTER HANDLING. STORE IN CLOSED CONTAINERS IN COOL, WELL
VENTILATED AREA.
SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION:
ATMOSPHERIC CONCENTRATIONS SHOULD BE MAINTAINED BELOW THE THRESHOLD LIMIT
GUIDELINES PROVIDED. WHEN THESE CONCENTRATIONS CANNOT BE MAINTAINED,
RESPIRATORY PROTECTION IS REQUIRED. USE NIOSH/MSA APPROVED CHEMICAL/MECHANICAL
FILTERS DESIGNED TO REMOVE A COMBINATION OF PARTICULATE, GASEOUS AND VAPOR
MATERIALS. IN CONFINED AREAS, USE A NIOSH/MSA APPROVED POSITIVE-PRESSURE, SELF-
CONTAINED BREATHING APPARATUS. WEAR RESPIRATORY PROTECTION SUCH AS NIOSH/MSHA
TC-21C-132 DUST/MIST RESPIRATOR WHEN SANDING, GRINDING, BLASTING OR CUTTING THE
DRY FILM OF THIS MATERIAL.
MATERIAL SAFETY DATA SHEET
Page: 5
PERMA-CLEAN 100 EPOXY
5/21/2009
VENTILATION:
WHERE POSSIBLE, PROVIDE GENERAL AND/OR LOCAL EXHAUST VENTILATION TO CONTROL
AIRBORNE LEVELS BELOW THE THRESHOLD LIMIT VALUES.
SKIN PROTECTION:
SKIN CONTACT SHOULD BE AVOIDED. USE IMPERVIOUS GLOVES AND LONG SLEEVED
CLOTHING. USE APPROPRIATE BARRIER CREAMS ON EXPOSED SKIN.
EYE PROTECTION:
USE SPLASH PROOF CHEMICAL GOGGLES OR SAFETY GLASSES WITH SIDE SHIELDS.
OTHER RECOMMENDED PROTECTIVE MEASURES:
USE IMPERMEABLE CLOTHING, APRONS AND PROTECTIVE COVERING WHENEVER POSSIBLE TO
PREVENT SKIN CONTACT. WEAR HEAD COVERING WHENEVER POSSIBLE.
RECOMMENDED HYGIENIC PRACTICES:
WASH HANDS AND ARMS WITH SOAP AND WATER PRIOR TO EATING, DRINKING, SMOKING OR
USING THE LAVATORY.
SECTION IX - DISCLAIMERS
THE INFORMATION CONTAINED HEREIN IS BASED PRIMARILY ON DATA PROVIDED US BY OUR
SUPPLIERS, AND WE BELIEVE IT TO BE CORRECT. HOWEVER, INDURON COATINGS, INC.
MAKES NO WARRENTY, EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THESE DATA OR
THE RESULTS TO BE OBTAINED FROM THE USE THEREOF. INDURON ASSUMES NO
RESPONSIBILITY FOR INJURY FROM THE USE OF THE PRODUCT DESCRIBED HEREIN.
MATERIAL SAFETY DATA SHEET
Page: 1
PERMA-CLEAN 100 EPOXY ACTIVATOR
5/21/2009
PRODUCT NAME: PERMA-CLEAN 100 EPOXY ACTIVATOR HMIS CODES: H F R P
PRODUCT CODE: Q-4165 211G
SECTION I - MANUFACTURERS IDENTIFICATION
MANUFACTURER'S NAME: INDURON PROTECTIVE COATINGS, INC.
ADDRESS: 3333 RICHARD ARRINGTON Jr BLVD, N.
BIRMINGHAM, ALABAMA 35234
EMERGENCY PHONE: (205) 324-9584 INFORMATION PHONE: (205) 324-9584
DATE PRINTED: 5/21/2009 NAME OF PREPARER: John Anspach
SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONANTS CAS NUMBER mm Hg @ TEMP PERCENT
---------------------------------------------------------------------------------------------------------------------------------
ALIPHATIC AMINE, MODIFIED 7.5 70 F 25 - 30%
NONE ESTABLISHED
! MICROCRYSTALLINE SILICA 98.5-99.0% 14808-60-7 N/A 22.29
PEL-TLV/TWA=0.1 MG/M3 (RESPIRABLE DUST)
! OXIDE GLASS 65997-17-3 N/A 15 - 20%
ACGIH TLV NOT ESTABLISHED
OSHA PEL 5 MG/M3 RESPIRABLE
NONREACTIVE DILUENT NONE N/A 10 - 15%
NONE ESTABLISHED
! TITANIUM DIOXIDE 13463-67-7 N/A 10 - 15%
TLV/TWA=10 MG/M3 TOTAL DUST OR 5 MG/M3 (NUISANCE DUST)
2,4,6-TRI(DIMETHYLAMINOMETHYL) PHENOL 90-72-2 N/A < 5%
NONE ESTABLISHED
BENZYL ALCOHOL, TECHNICAL GRADE 100-51-6 .1 86 F < 5%
NONE ESTABLISHED
HYDROPHOBIC AMORPHOUS FUMED SILICA 68611-44-9 N/A < 5%
OSHA PEL=5 MG/M3 RESPIRABLE DUST, 15 MG/M3 TOTAL DUST
* INDICATES TOXIC CHEMICAL(S) SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III OF 40
CFR 372.
! NOTE: PIGMENTS DO NOT NORMALLY POSE A DUST HAZARD IN COATINGS.
Warning: Detectable amounts of chemicals known to the State of California to cause cancer and/or birth defects or
reproductive harm may be present in this product.
MATERIAL SAFETY DATA SHEET
Page: 2
PERMA-CLEAN 100 EPOXY ACTIVATOR
5/21/2009
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
BOILING RANGE: 400 F - 572 F DENSITY: 10.101 lb/gl
VAPOR DENSITY: HEAVIER THAN AIR.
EVAPORATION RATE: SLOWER THAN DIETHYL ETHER.
COATING VOC (Water Excluded): 0.22 lb/gl,26 g/l
SOLUBILITY IN WATER: INSOLUBLE.
APPEARANCE AND ODOR:
Opaque, viscous liquid. Aromatic Hydrocarbon solvent odors.
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 210 F METHOD USED: TCC
FLAMMABLE LIMITS IN AIR BY VOLUME-LOWER: N/A UPPER: N/A
EXTINGUISHING MEDIA:
CARBON DIOXIDE, FOAM, DRY CHEMICAL, WATER SPRAY.
SPECIAL FIREFIGHTING PROCEDURES:
USE SELF CONTAINED BREATHING APPARATUS. WATER SHOULD BE USED AS A FOG ONLY, TO
KEEP CONTAINERS COOL IN ORDER TO MINIMIZE PRESSURE BUILDUP AND EXPLOSION.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
THIS MATERIAL WILL NOT SUSTAIN COMBUSTION UNLESS PREHEATED. IF CONTAINER IS NOT
PROPERLY COOLED, IT MAY EXPLODE IN THE HEAT OF A FIRE.
SECTION V - REACTIVITY DATA
STABILITY: STABLE UNDER NORMAL CONDITIONS OF STORAGE AND HANDLING.
CONDITIONS TO AVOID:
AVOID HEAT, SPARKS, FLAME AND OTHER POSSIBLE IGNITION SOURCES.
INCOMPATIBILITY (MATERIALS TO AVOID):
AVOID CONTACT WITH STRONG OXYDIZING AGENTS. AVOID BRINGING INTO CONTACT WITH
LOW MOLECULAR WEIGHT EPOXY RESINS UNDER UNCONTROLLED HIGH TEMPERATURE
CONDITIONS.
HAZARDOUS DECOMPOSITION BYPRODUCTS:
IGNITION MAY YIELD CARBON MONOXIDE, CARBON DIOXIDE AND OXIDES OF NITROGEN.
HAZARDOUS POLYMERIZATION:
WILL NOT OCCUR.
MATERIAL SAFETY DATA SHEET
Page: 3
PERMA-CLEAN 100 EPOXY ACTIVATOR
5/21/2009
SECTION VI - HEALTH HAZARD DATA
SKIN CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
THIS MATERIAL MAY CAUSE SEVERE INJURY TO SKIN FOLLOWING PROLONGED OR REPEATED
CONTACT AND MAY CAUSE SENSITATION OR OTHER ALLERGIC RESPONSES. A SINGLE
PROLONGED EXPOSURE MAY RESULT IN MATERIAL BEING ABSORBED IN HARMFUL AMOUNTS.
EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
CAN QUICKLY CAUSE SEVERE IRRITATION OR BURNS. MAY CAUSE PERMANENT VISUAL
IMPAIRMENT, AND ULTIMATELY, BLINDNESS.
SENSITIZATION:
POTENTIAL SKIN SENSITIZER.
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
BREATHING HIGH CONCENTRATIONS OF AEROSOLS OF THIS MATERIAL MAY CAUSE IRRITATION
OF THE NOSE, THROAT AND RESPIRATORY TRACT. DUST FROM THIS MATERIAL MAY CONTAIN
TRACE AMOUNTS OF CRYSTALLINE SILICA. FREQUENT INHALATION OF HIGH CONCENTRATIONS
OF DRY DUST GENERATED BY SANDING, CUTTING, BLASTING OR GRINDING THIS MATERIAL
OVER A LONG PERIOD OF TIME MAY CAUSE CANCER. RESPIRATORY SYMPTOMS ASSOCIATED
WITH PRE-EXISTING LUNG DISORDERS (E.G., ASTHMA-LIKE CONDITIONS) MAY BE
AGGRAVATED BY EXPOSURE TO DUST AND AEROSOLS OF THIS MATERIAL.
ORAL INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
WHILE THIS MATERIAL HAS A LOW DEGREE OF TOXICITY, INGESTION COULD CAUSE
GASTROINTESTINAL IRRITATION OR ULCERATION. INGESTION MAY CAUSE BURNS OF THE
MOUTH AND THROAT.
EFFECTS OF OVEREXPOSURE:
INHALATION:
DIZZINESS, BREATHING DIFFICULTY, HEADACHES, LOSS OF COORDINATION.
EYE CONTACT:
SEVERE IRRITATION, TEARING, REDNESS, AND BLURRED VISION.
SKIN CONTACT:
CONTACT WITH SKIN QUICKLY CAUSES SEVERE IRRITATION AND PAIN AND MAY CAUSE BURNS.
INGESTION:
CAN CAUSE GASTROINSTESTINAL IRRITATION ,BURNS OR ULCERATION.
CARCINOGENICITY: NTP?YES IARC MONOGAPHS?YES
NOTE: DUST FROM THIS MATERIAL MAY CONTAIN TRACE AMOUNTS OF CRYSTALLINE SILICA.
PERSONS IN THE IMMEDIATE VICINITY OF SANDING, CUTTING, BLASTING AND
GRINDING OPERATIONS ON THE DRY FILM SHOULD WEAR RESPIRATORY PROTECTION.
REFER TO THE RESPIRATORY PROTECTION SECTION OF THIS DOCUMENT.
OSHA REGULATED?YES.
MATERIAL SAFETY DATA SHEET
Page: 4
PERMA-CLEAN 100 EPOXY ACTIVATOR
5/21/2009
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
ALLERGY, ECZEMA, ASTHMA, OTHER SKIN CONDITIONS.
EMERGENCY AND FIRST AID PROCEDURES:
EYE CONTACT:
IRRIGATE WITH FLOWING WATER IMMEDIATELY AND CONTINUOUSLY FOR 30 MINUTES.
CONSULT MEDICAL PERSONNEL.
SKIN CONTACT:
IMMEDIATELY REMOVE CONTAMINATED CLOTHING AND REMOVE EXCESS FROM SKIN. WASH OFF
WITH SOAP AND FLOWING WATER OR SHOWER. WASH CLOTHING BEFORE REUSE.
CONTAMINATED LEATHER ARTICLES, INCLUDING SHOES, CANNOT BE DECONTAMINATED
AND SHOULD BE DISCARDED. IF SKIN IRRITATION OCCURS, SEE A PHYSICIAN.
INGESTION:
DO NOT INDUCE VOMITING. ADMINISTER LARGE AMOUNTS OF WATER OR MILK IF AVAILABLE.
CALL A PHYSICIAN AND/OR TRANSPORT TO A MEDICAL FACILITY IMMEDIATELY.
INHALATION OVEREXPOSURE:
IF RESPIRATORY SYMPTOMS DEVELOP, MOVE VICTIM AWAY FROM SOURCE OF EXPOSURE AND
INTO FRESH AIR. IF SYMPTOMS PERSIST, SEEK MEDICAL ATTENTION. IF VICTIM IS
NOT BREATHING, IMMEDIATELY BEGIN ARTIFICIAL RESPIRATION. IF BREATHING
DIFFICULTIES DEVELOP, OXYGEN SHOULD BE ADMINISTERED BY QUALIFIED PERSONNEL.
GET IMMEDIATE MEDICAL ATTENTION.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
REMOVE ALL SOURCES OF IGNITION. PROVIDE EXPLOSION PROOF VENTILATION. DIKE
SPILL AREA AND TAKE UP ON ABSORBENT MATERIAL. SHOVEL WITH NON-SPARKING TOOLS
INTO CLOSABLE CONTAINER FOR DISPOSAL. WEAR PROTECTIVE EQUIPMENT SPECIFIED
BELOW. THOROUGHLY FLUSH CONTAMINATED AREA WITH WATER.
WASTE DISPOSAL METHOD:
DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
KEEP AWAY FROM HEAT, SPARKS AND OPEN FLAME. AVOID CONTACT WITH EYES, SKIN AND
CLOTHING. AVOID BREATHING VAPOR, MIST OR SPRAY. USE ONLY WITH GOOD
VENTILATION. WASH AFTER HANDLING. STORE IN CLOSED CONTAINERS IN COOL, WELL
VENTILATED AREA.
SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION:
ATMOSPHERIC CONCENTRATIONS SHOULD BE MAINTAINED BELOW THE THRESHOLD LIMIT
GUIDELINES PROVIDED. WHEN THESE CONCENTRATIONS CANNOT BE MAINTAINED,
RESPIRATORY PROTECTION IS REQUIRED. USE NIOSH/MSA APPROVED CHEMICAL/MECHANICAL
MATERIAL SAFETY DATA SHEET
Page: 5
PERMA-CLEAN 100 EPOXY ACTIVATOR
5/21/2009
FILTERS DESIGNED TO REMOVE A COMBINATION OF PARTICULATE, GASEOUS AND VAPOR
MATERIALS. IN CONFINED AREAS, USE A NIOSH/MSA APPROVED POSITIVE-PRESSURE, SELF-
CONTAINED BREATHING APPARATUS. WEAR RESPIRATORY PROTECTION SUCH AS NIOSH/MSHA
TC-21C-132 DUST/MIST RESPIRATOR WHEN SANDING, GRINDING, BLASTING OR CUTTING THE
DRY FILM OF THIS MATERIAL.
VENTILATION:
WHERE POSSIBLE, PROVIDE GENERAL AND/OR LOCAL EXHAUST VENTILATION TO CONTROL
AIRBORNE LEVELS BELOW THE THRESHOLD LIMIT VALUES.
SKIN PROTECTION:
SKIN CONTACT SHOULD BE AVOIDED. USE IMPERVIOUS GLOVES AND LONG SLEEVED
CLOTHING. USE APPROPRIATE BARRIER CREAMS ON EXPOSED SKIN.
EYE PROTECTION:
USE SPLASH PROOF CHEMICAL GOGGLES OR SAFETY GLASSES WITH SIDE SHIELDS.
OTHER RECOMMENDED PROTECTIVE MEASURES:
USE IMPERMEABLE CLOTHING, APRONS AND PROTECTIVE COVERING WHENEVER POSSIBLE TO
PREVENT SKIN CONTACT. WEAR HEAD COVERING WHENEVER POSSIBLE.
RECOMMENDED HYGIENIC PRACTICES:
WASH HANDS AND ARMS WITH SOAP AND WATER PRIOR TO EATING, DRINKING, SMOKING OR
USING THE LAVATORY.
SECTION IX - DISCLAIMERS
THE INFORMATION CONTAINED HEREIN IS BASED PRIMARILY ON DATA PROVIDED US BY OUR
SUPPLIERS, AND WE BELIEVE IT TO BE CORRECT. HOWEVER, INDURON COATINGS, INC.
MAKES NO WARRENTY, EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THESE DATA OR
THE RESULTS TO BE OBTAINED FROM THE USE THEREOF. INDURON ASSUMES NO
RESPONSIBILITY FOR INJURY FROM THE USE OF THE PRODUCT DESCRIBED HEREIN.
|