TECHNICAL DATA
PRO-FOAM IITM
MINIMALLY
PHYSICAL PROPERTIES
EXPANDING Type One-component polyurethane foam
Color Off-white
SEALANT
R-Factor 5 per inch (aged) @ 75癋 (24癈)
Toxicity Toxic only if swallowed uncured
Cut Time < 1 Hour
Cure Time 4 ?24 hours @ 75癋 (24癈), 50% RH
OSI?GreenSeriesTM Pro-Foam Tack Free Time 10-15 minutes @ 70癋 (21癈), 40% RH
IITM Minimally Expanding Tensile Strength 15 p.s.i. (ASTM D-1623)
Compression Strength
Sealant is a one part, moisture
Parallel @ 10% 10 ?14 p.s.i. (ASTM D-1621)
cure polyurethane foam in a 33oz
Closed Cell Content >70% (ASTM D-2856)
pressurized container. It is specially
Water Vapor Transmission 5.97 perms (ASTM E-96)
designed to be dispensed in bead Heat Resistance +200癋. (+93癈)
form for filling gaps, cracks and Cold Resistance -200癋. (-129癈)
holes in most types of construction VOC Level 0 g/l
projects to stop energy draining Expansion Characteristics +/- 40% of dispensed volume w/ Pro Gun
drafts and sound transmission. The Flame Spread** 20 (UL 723, ASTM E-84)
Smoke Density 70 (UL 723, ASTM E-84)
closed cell, energy saving foam
Flammability This product is organic and therefore flammable
insulates with an R-5 factor per inch
and may constitute a fire hazard if improperly used
of foam with slight to minimal
or installed. It should not be left exposed or
expansion. Pro-Foam II adheres to inadequately protected. It is strongly recommended
all types of wood, metal, concrete, that in all applications the foam be protected by
brick, glass, drywall, most plastics plaster, drywall, cement or other approved facings.
and other building materials. Clean-up Pro Series?Pro Clean or other solvents prior to
curing. Cured foam cannot be removed except by
abrasion or other mechanical means.
FEATURES
?Does not contain Formaldehyde
** When references are made to flame spread ratings, these numerical flame spread
?Slight/Moderate Expansion
ratings are not intended to reflect hazards presented by these or any other materials
?Quick Setting Formula under actual fire conditions. NOTE: Physical Properties shown are typical and are to
?Meets LEED requirements serve only as a guide for engineering design. Results are obtained from specimens
?Reduces Sound & Air under ideal laboratory conditions and may vary upon use, temperature and ambient
transmissions conditions. Right to change physical properties as a result of technical progress is
?Fast & Easy to use reserved.
?High Insulating qualities
CONTENTS: 4, 4' ?Dihenylmethane Diisocyanate (MDI: CAS #101-68-8), Higher
?Insect/Rodent resistant
Oligomers of MDI (CAS #9016-87-9), Polyol (CAS #25791-96-2), 2,2; 2, 4
Diphenylmethane Diisocyanate (CAS #26447-40-5), Hydrofluoroalkane (one or more
USES of the following: CAS #75-45-6, CAS #75-68-3, CAS #1717-00-6, CAS #306-83-2,
GreenseriesTM Pro-Foam IITM is used CAS #75-71-8).
to insulate and seal around
windows, door frame joints, jambs, ______________________________________________________________
mud sills, header and corner joints,
top plate penetrations, exterior and Ideal for adhering and joining Also works well as an effective
T joints, electrical & plumbing insulation panels, and when used acoustical sealant for reducing
penetrations, and other areas where with Pro Series?Pro Gun II, may sound transmissions and
air infiltrates or heat loss can occur. be used in place of conventional maintaining specified STC values in
adhesives for adhering drywall to most wall partitions.
wood framing.
1
SPECIFICATIONS COVERAGE Product must not be left
?UL Classified ?file #R11059 " - ? bead size: 1100 lin. ft. * exposed but should be covered
caulking and sealants ASTM with at least ?inch cement,
*Yield shown are optimum and will vary
E-84 (UL 723) U.B.C. Class plaster or fire-sated gypsum
slightly depending on ambient conditions,
the particular application, the dispensing
I: Standard No. 42.1 board or an equivalent barrier
method, or the user's ability.
?Complies with the following providing a finished fire rating
model building codes to of 15 minutes or more.
APPLICATION PROCEDURES
help complement insulation Urethane foam should not be
?Safety first. Always wear
programs: used in contact with chimneys,
gloves, goggles and proper
?HUD Minimum Properties heater vents, steam pipes or
work clothes.
Stds. (Sec. 507.6) other areas which could be
?Read all operating instructions
?B.O.C.A. ?Basic Energy subject to surface temperatures
before using
Code exceeding 200癋. Avoid doing
?All surfaces must be free of
1977 (Sec. 301.4.3) hot work or flame cutting
dust, dirt, oil and other
?I.C.B.O. ?Uniform Building around urethane foam. If
foreign materials.
Code (Sec. 5303 (e)) necessary, follow the
?For best performance,
?A.S.H.R.A.E. ?Standard 90- recommended industrial
containers should be kept at
75 (Sec. 45.4) procedures.
65癋 to 90癋 and relative
?SCAQMD Rule 1168 V.O.C.; humidity sufficient to cure
Urethane foams are adversely
CARB; and BAAQMD foam.
affected by sunlight (ultraviolet
compliant DIRECTIONS
light). For this reason as well as
?Meets LEEDS requirements 1.Cover surfaces not intended
for fire safety, it is
to be foamed as cured foam is
recommended that a protective
LIMITATIONS difficult to remove.
coating be applied over the
1. In cold weather applications, 2.Perimeter seal all openings.
containers should be kept at finished foam.
Deep cavities only need to be
65癋 (18癈) for maximum
filled 30% to affect proper
performance. Product WARNING
seal against air infiltration or
temperatures below 55癋 Follow safety precautions and
energy loses. Foam is tack
(13癈) will experience slow
wear protective equipment as
free in approximately 30
extrusion rates.
recommended. Use only with
2. Pro-Foam IITM is not a fire minutes and cured in 4 ?24
adequate ventilation or certified
stopping material and should hours.
respiratory protection. Contents
not be used in areas that 3.If necessary, cured foam can
are very sticky and may be
require fire proof or fire stop
be trimmed with a sharp knife
materials. irritating to skin and eyes,
or sanded.
3. Pro-Foam IITM will not adhere to therefore wear safety glasses,
4.Cured foam exposed to
polyethylene, PTFE, oils, gloves and adequate clothing
sunlight must be covered with
greases, mold release agents
when using.
paint, sealant or solid colored
and similar materials.
4. Containers are date coded. No stain.
KEEP OUT OF REACH OF
returns after expiration date. 5.When containers are empty,
CHILDREN
Shelf life: 9 months from date vent off any excess pressure
of manufacture.
carefully and dispose of in FIRST AID
appropriate waste container. Eye Contact: In case of eye
PACKAGING
DO NOT incinerate. contact, immediately flush with
33oz. Can ?9 per case
6.Use OSI?Pro Series?Pro clean water for at least 15
(Item No. GS99910)
CleanTM to clean up spills and minutes and seek medical
tools before foam cures.
STORAGE attention immediately. Skin
Note: Cured foam is not
Store in cool, dry location Contact: Wipe off thoroughly
affected by solvents and is
preferably at room temperature, suing a dry cloth. Wash with
difficult to remove.
and not less than 65?F (18C) soap and water. Apply hand
or greater than 90?F (32癈) for lotion if desired. Ingestion:
ADDITIONAL INFORMATION
maximum performance and Seek immediate medical
In many areas there are
shelf life. Containers are under attention. Take instructions to
applicable building code(s) which
pressure. Do Not expose to physicians for chemical
may cover the use of cellular
open flame or temperatures identification. Persons with
plastics or urethane foam either
above 120癋 (49癈). Excessive chronic respiratory disease,
generally or specifically as
heat can cause premature aging asthma or bronchial medical
exposed, interior, or finishing
of components resulting in history, or history of presence
material. Under certain of these
shorter shelf life. of allergic disease should not
codes, the use of our product may
work with these materials.
be restricted or prohibited.
NOTE: When storing Foam Dispensing
Applicators with foam cans attached, be
Consult Material Safety Data
sure to store the tool with the can valve
Sheet (MSDS) for more
pointing downwards. Storing the can up-
information.
right may cause propellant to leak and
2
the foam applicator to become
inoperative.
OPTIONAL ACCESSORIES
NOTICE TO PURCHASER
Henkel Corporation warrants this
OSI?Pro Series?PG-915 Pro Gun II
product when used according to
(91500) Precision high quality
directions. If not satisfied with the
dispensing applicator.
product's performance when used
as directed, return sales receipt
OSI?Pro Series?PG-915P Pro Gun I
and used container to Henkel
(91501) Precision plastic dispensing
Corporation, 32150 Just Imagine
applicator.
Drive, Avon OH, 44011 for
product replacement or refund.
A Pro Gun is a require when using
User shall determine suitability of
GreenseriesTM Pro-Foam IITM Sealant.
product for use and assumes all
risk.
QUESTIONS?
For commercial use or other questions
In the event of any claim,
pertaining to this product, call Henkel
notification must be sent in
Technical Service at 800-321-0253,
writing to Henkel Corporation
M-F, 9am ?4pm.or visit our website
within 30 days of occurrence.
at www.greenseries.com.
OSI?GreenSeriesTM Pro-Foam
IITM Minimally Expanding
Sealant is currently under
going tested by GREENGUARD.
The GREENGUARD INDOOR AIR
QUALITY CERTIFIED Mark is a
registered certification mark
used under license through the
GREENGUARD Environmental
Institute.
Henkel Corporation
Professional and Consumer Adhesives
32150 Just Imagine Drive
Avon, OH 44011
U.S.A.
Phone: (440) 937-7000
Fax: (440) 937-7092
3
sG11105
|