Gazette
Commonwealth
of Australia
No. C 2, Tuesday, 3 February 2004
CHEMICAL
Published by the Commonwealth of Australia
ISSN 1035-9877
The Industrial Chemicals (Notification and Assessment) Act 1989 (the Act) commenced on
17 July 1990. As required by Section 5 of the Act, a Chemical Gazette is published on the
first Tuesday in any month or on any days prescribed by the regulations.
CONTENTS
NEW CHEMICALS
SUMMARY REPORTS
1 LTD/1025 X2473 5
2 LTD/1061 K1334 8
3 LTD/1077 POLYMER IN RW3131 10
4 LTD/1100 CYAN DYE 2 12
5 LTD/1112 VIVALDIE 14
6 LTD/1117 POLYMER IN PHOTOGLAZE U179 18
7 LTD/1119 PIGMENT ADDITIVE FGR 21
8 LTD/1121 AZ-57-5328 24
9 LTD/1122 AZ-53-1326 27
10 LTD/1125 ZSR-20BE4 29
11 STD/1038 RAV 7 NG 31
12 EX/47 Z-38 34
13 PLC/384 FLUOROCHEMICAL URETHANE 38
14 PLC/400 RESYDROL 586W/45WA 40
15 PLC/402 POLYMER IN EMULSION EXP-3913 42
16 PLC/411 ARISTOFLEX AVC 44
17 PLC/422 SILICON POLYAMIDE 46
18 PLC/424 SCALEGUARD 60116 48
ABS COPOLYMER RESIN
19 PLC/429 51
20 ACCESS TO FULL PUBLIC REPORT 53
PERMITS ISSUED
21 LOW VOLUME CHEMICAL PERMITS 54
22 EARLY INTRODUCTIN PERMITS 55
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES
23 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE 56
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES FIVE
YEARS AFTER ISSUING OF ASSESSMENT CERTIFICATES
SPECIAL NOTICES
24 LOW REGULATORY CONCERN CHEMICALS REFORM 57
INITIATIVE
25 NOTICE OF PUBLICATION OF SODIUM ALKYL BENZENE 58
SULFONATE ANTI-VALVE SEAT RECESSION ADDITIVE
SUMMARY REPORT
26 AICS ONLINE TRAINING SESSIONS 60
27 CALL FOR INFORMATION ON CHEMICALS 61
5
1 PUBLICATION SUMMARY REPORT
X2473
Summary Report
Reference No: LTD/1025
International Sales and Marketing Pty Ltd (ABN 36 467 259 314) of 262 Highett Road
HIGHETT VIC 3190 has submitted a limited notification statement in support of their
application for an assessment certificate for X2473. The notified polymer is intended to be
used as a component of water based wood and furniture coatings and high build coatings to
reduce or eliminate microform. Less than 10 tonnes of the notified chemical will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicological data were provided.
The notified polymer has a high molecular weight and is therefore unlikely to cross biological
membranes.
It contains a high concern reactive functional group with a functional group equivalent
weight of around 1000. This may lead to skin irritant effects for concentrated polymer
solutions.
The MSDS states that the product is considered to be "harmless if used in the correct
manner". Eye contact may produce an oil film over the eye-ball causing a harmless reversible
shortlasting dimness of sight.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as described in the submission.
Environmental Effects
On the basis of the risk characterisation presented in this report, the polymer is not considered
to pose a risk to the environment based on its report use pattern.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
6
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The following safety phrases should be used for the notified chemical as introduced:
- S24/25 Avoid contact with skin and eyes
- S26 In case of contact will eyes, rinse immediately with plenty of water and seek
medical advice
- S28 After contact with skin, wash immediately with plenty of soap-suds
- S36/37/39 Wear suitable protective clothing, gloves and eye/face protection
Control Measures
Occupational Health and Safety
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced, and in
the finished paint products:
- Prevent spills and splashes
- NOHSC Exposure Standards for all components of the final paint products should not
be exceeded in the workplace.
- Use of spray paints containing the notified polymer should be accordance with the
NOHSC National Guidance Material for Spray Painting
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced,
and in the finished paint product
- Chemical resistant gloves, protective clothing, and safety goggles or safety glasses
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? The following control measures should be implemented by end users to minimise
environmental exposure during use of the notified chemical:
- Do not pour paint residues down the drain. Unwanted paints should be brushed out
on newspaper, allowed to dry and then disposed of via domestic waste collections.
Empty paint containers should be left open in a well-ventilated area to dry out. When
dry recycle steel containers via steel can recycling program. Disposal of empty
containers via domestic recycling programs. Disposal of empty paint containers via
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
7
domestic recycling programs may differ between local authorities. Check with local
council first.
Disposal
? Once dry the notified polymer should be disposed of by landfill or by incineration.
Emergency procedures
? Spills/release of the notified polymer should be handled by collecting with non
combustible absorbent materials and placing in a suitable container for disposal
according to Local, State and Federal Government waste regulations.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
8
2 PUBLICATION SUMMARY REPORT
K-1334
Summary Report
Reference No: LTD/1061
ILFORD Imaging Asia Pacific Pty Limited (ABN 69 004 283 701) of Unit 1/10 Duerdin
Street Clayton North VIC 3168 (ABN 69 004 283 701) and Hewlett-Packard Australia Pty
Ltd (ABN 74 004 394 763) of 31-41 Joseph Street Blackburn VIC 3130 has jointly submitted
a limited notification statement in support of their application for an assessment certificate for
K-1334. The notified chemical is intended to be used as a component of pre-packed inkjet
cartridges of 25 to 55 mL capacity. The imported cartridges containing the notified chemical
may be transported by road to their distribution location. The inks will contain a maximum of
<10% w/w notified chemical. The notified chemical will be imported between 100 ?1000 kg
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used as a component of printing ink.
Environmental Effects
On the basis of the PEC/PNEC ratio:
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
No special precautions are required for the notified chemical when used at low quantities as a
component of ink cartridges for printers. However, in the interests of good occupational
health and safety, the following guidelines and precautions should be observed for use of
printing inks containing the notified chemical:
?Avoid contact with skin.
?Printers should be located in well-ventilated areas.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
9
? Service personnel should wear cotton or disposable gloves when replenishing spent
ink cartridges and servicing printers.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? The following control measures should be implemented by end users to minimise
environmental exposure during use of the notified chemical:
- Do not allow material or contaminated packaging to enter drains, sewers or water
courses.
Disposal
? The notified chemical should be disposed of to landfill.
Emergency procedures
? Spills/release of the notified chemical should be contained and collected for disposal
in landfill. Do not allow this strongly coloured substance to enter drains.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
10
3 PUBLICATION SUMMARY REPORT
Polymer in RW3131
Summary Report
Reference No: LTD/1077
BASF Akzo Nobel Automotive OEM Coatings Pty Ltd of McIntyre Road, Sunshine VIC
3020 (ABN: 91 092 127 501), and Akzo Nobel Pty Ltd of McIntyre Road Sunshine VIC
3020 (59 000 119 424) have submitted a joint limited notification statement in support of
their application for an assessment certificate for Polymer in RW3131. The notified polymer
is intended to be used in an automotive primer for car bodies and parts. Up to 1000 tonnes
notified chemical will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified polymer is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
There are insufficient data available to allow environmental classification under the GHS.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is no significant concern to public health when used in the intended manner.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified polymer in principal emulsion and the final
cathodic electrodeposition primer:
- Local exhaust ventilation
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer in principal
emulsion and the final cathodic electrodeposition primer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
11
- Protective eyewear, impermeable gloves and chemical resistant industrial clothing and
footwear.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
? Prevent uncontrolled release into the environment.
Disposal
? Dispose of unused product, or waste material containing the notified chemical to
landfill or in accordance with local regulations.
Emergency procedures
? Contain liquid spills and prevent product from flowing into drains.
? Dike and contain spills with inert material and transfer to containers for recovery or
disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
12
4 PUBLICATION SUMMARY REPORT
Cyan Dye 2
Summary Report
Reference No: LTD/1100
Toxikos Pty Ltd (ACN 30 095 051 791) of PO Box 74, Caulfield East VIC 3145, and Hewlett
Packard Australia Pty Ltd (ACN 74 004 394 763) of 31-41 Joseph St, Blackburn VIC 3130,
have submitted a joint limited notification statement in support of their application for an
assessment certificate for Cyan Dye 2. The notified chemical is intended to be used in inkjet
reprographic processes. <1 tonne of the notified chemical will be imported per annum for
each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is negligible concern to public health when used in the intended manner.
Environmental Effects
On the basis of the PEC/PNEC ratio the chemical is not considered to pose a risk to the
aquatic environment based on its reported use pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Skin protection is essential when handling the notified chemical.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing Cyan Dye 2 are classified as hazardous to health
in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
13
Environment
Disposal
? The notified chemical should be disposed of to either landfill or be incinerated or
recycled with paper in accordance with local, state or national legislation.
Emergency procedures
? Spills/release of the notified chemical should be handled by containing, adsorbing and
cleaning up spillage and transferring to a container for disposal. Wash the spillage
area clean.
? Do not allow spilled/released chemical or washings to enter drains, sewers or
watercourses.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- over 1 tonne per annum of the notified chemical is used in Australia Test reports on
adsorption/desorption and dissociation constant are required to be submitted for the
notified chemical should import volumes reach this quantity.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
14
5 PUBLICATION SUMMARY REPORT
Vivaldie
Summary Report
Reference No: LTD/1112
International Flavours & Fragrances (Australia) Ltd (ABN 77 004 269 658) of 310
Frankston-Dandenong Rd Dandenong VIC 3175. has submitted a limited notification
statement in support of their application for an assessment certificate for Vivaldie. The
chemical name is 3-Hexene, 1-[(2-methyl-2-propenyl)oxy]-(3Z) and the Chemical Abstracts
Service Number is 292605-05-1. The notified chemical is intended to be used as a fragrance
component in personal and household products. The notified chemical is imported as a
component of a fragrance oil which is blended with other components into the various
products. One tonne of the notified chemical will be imported per annum for each of the first
five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
- R10: Flammable
- R38: Irritating to skin.
- S24/25 Avoid contact with skin and eyes.
- S37 Wear suitable gloves
The notified chemical is classified as a Dangerous Good under the Australian Code for the
Transport of Dangerous Goods by Road and Rail (ADG Code) :
- Class 3 ?Flammable liquid, Packing Group III.
According to the Globally Harmonised System for the Classification and Labelling of
Chemicals, the notified chemical is classified as:
Hazard category Hazard statement
Flammable liquids A2.6 3 Flammable liquid and
vapour
Skin corrosion / irritation 3 Causes mild skin
A2.18 irritation
Based on the data currently available, it is not possible to categorise the notified chemical for
the environment according to the Globally Harmonised System for the Classification and
Labelling of Chemicals. However, ECOSAR estimates indicate that the notified chemical is
toxic to fish and daphnia, and very toxic to algae.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
15
Public Health
There is No Significant Concern to public health when used in household and personal
consumer products.
Environmental Effects
On the basis of the PEC/PNEC ratio:
- The chemical is not considered to pose a risk to the environment based on its reported
use pattern and low level of import.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
hazard classification for the notified chemical:
- R10: Flammable
- R38: Irritating to skin.
- S24/25 Avoid contact with skin and eyes.
- S37 Wear suitable gloves
? Use the following risk phrases for products/mixtures containing the notified chemical:
- 20%: R38: Irritating to skin
? The notified chemical should be classified as follows under the ADG Code:
- Class 3 (flammable liquid), Packing Group III.
? Suppliers should label the notified chemical as a Class 3 dangerous good with the
class label [Flammable Liquid 3] and the risk and safety phrases listed above.
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical in perfume oil blends and consumer
products:
- Use of a closed or semi-closed system for weighing and formulation processes, where
possible
- Local exhaust ventilation or good general ventilation should be provided if the
weighing and formulation process is an open one.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical in perfume oil blends
and consumer products:
- Prevent splashes and spills.
- Avoid direct handling of the perfume blends where possible.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
16
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical in perfume oil
blends and consumer products:
- Chemical resistant gloves, protective overalls and goggles/faceshield.
- Respiratory protection should be used if the perfume blend is handled in a confined
space.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? The following control measures should be implemented by reformulator to minimise
environmental exposure during product formulation of the notified chemical:
- Bunding and catch drains to prevent any material entering stormwater drains or
adjacent natural waterways.
Disposal
? The notified chemical should be disposed of to on-site effluent treatments plants or to
approved landfills.
Emergency procedures
? Spills/release of the notified chemical should be contained and adsorbed by using
sand or inert powder and earth. The collected material should be placed in labelled,
sealable drums and disposed of to landfill.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Sub-Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical; or
- the notified chemical is imported as a pure chemical or at 20% in a mixture; or
- the concentration of the notified chemical in a product available to the public
increases to 0.5%; or
- further toxicological data on the notified chemical becomes available eg a 90-day
repeated dose study.
or
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
17
Under Sub-Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
If import increases above 1 tonne, ecotoxicity studies with fish, Daphnia and algae will have
to be undertaken to confirm high toxicity and the full results and reports submitted for
assessment. Test reports for vapour pressures and adsorption/desorption will also have to be
submitted.
If the notified chemical is imported as a pure chemical rather than as part of a mixture, a test
report for auto-ignition temperature will have to be submitted.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
18
6 PUBLICATION SUMMARY REPORT
Polymer in Photoglaze U179
Summary Report
Reference No: LTD/1117
Lord Chemical Products (Australia) Pty Ltd (ABN 85 085 209 712) of 21 Beverage Drive
Tullamarine VIC 3040 has submitted a limited notification statement in support of their
application for an assessment certificate for Polymer in Photoglaze U179. The notified
polymer is intended to be used as component of ink for screen-printing process. The notified
polymer will be imported as a component of a partially formulated ultraviolet (UV) curable
ink vehicle, Photoglaze U179, at a concentration of 52%. At the customer's site, the imported
ink vehicle will be used in the manufacture of UV curable inks for screen-printing process.
Manufactured inks will be packed in 5 kg cans, 20 kg pails or 200 kg drums, stored and
distributed by road to printing press companies all over Australia. The manufactured inks and
varnishes will contain 12 to 16% notified polymer. Less than 10 tonnes of the notified
polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the presence of hydroxyethyl acrylate at >0.5% as a residual monomer, the notified
polymer is classified as hazardous under the NOHSC Approved Criteria for Classifying
Hazardous Substances. The classification and labelling details are:
- R21 - Harmful in contact with skin; and
- R43 - May cause sensitisation by skin contact.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used in the manufacture of ink for
screen printing applications.
Environmental Effects
Although the PEC/PNEC ratio could not be calculated, the notified polymer is not considered
to pose a risk to the environment based on its reported use pattern and expected fate in the
environment.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
19
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified polymer:
- R21 - Harmful in contact with skin; and
- R43 - May cause sensitisation by skin contact.
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified polymer:
- Exhaust ventilation during transfer from drums to mix tank, mixing, filling into
containers and screen printing operations.
- Enclosed and automated ink manufacture and screen printing operations.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer:
- During transfer operations and cleaning equipment, avoid spills and splashing.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer:
- Chemical resistant gloves;
- Protective clothing which protects the body, arms and legs;
- Safety glasses; and
- Respiratory protection, as required.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of by a licensed waste contractor in
accordance with federal, State and local environmental control regulations.
? Empty containers should be recycled or disposed of through an approved waste
management facility.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
20
Emergency procedures
? Spills/release of the notified polymer should be contained and prevented from
entering drains, streams or any water body. The spilled material should be collected
with sand, vermiculite or other non-combustible absorbent material and place in clean
and suitable containers for disposal.
? For large spills or if sewers or waterways have been contaminated, contact local
Emergency Services.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
21
7 PUBLICATION SUMMARY REPORT
Pigment Additive FGR
Summary Report
Reference No: LTD/1119
Clariant (Australia) Pty Ltd (ABN 30 069 435 552) of 675 Warrigal Road Chadstone VIC
3148 has submitted a limited notification statement in support of their application for an
assessment certificate for Pigment Additive FGR. The notified chemical is intended to be
used as an ingredient in colourants for decorative coatings. The notified chemical will be
imported into Australia as a component of solid pigment products, Permanent Red FGR 02, at
<5% concentration. The pigment products will be packaged, stored and transported in 25 kg
multi-layer paper sacks inside fibreboard cartons. The pigment products will be transported
by road to contract stores for subsequent distribution to customers as required. At the
customer site, the pigment products will be used in the formulation of various paint tinter
formulations and subsequently added to form tinted paint products. Less than 1 tonne of the
notified chemical will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
There are no toxicological data available for the notified chemical since the chemical does
not exist in a pure form. A limited number of toxicity studies were conducted on products
either containing <5% notified chemical or of a substance structurally similar to the notified
chemical. These studies have been provided and accepted as "read across data" for the
assessment of the possible adverse health effects of the notified chemical. On the basis of the
data supplied, the notified chemical would not be classified as hazardous substance in
accordance with the NOHSC Approved Criteria for Classifying Hazardous Substances
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used as an ingredient in colourants for
decorative paints.
Environmental Effects
A PEC/PNEC ratio cannot be determined. However, based on low environmental exposure
resulting from its low import volume and widespread use, the likely risk to the aquatic
environment is expected to be low.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
22
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical in the pigment product:
- Exhaust ventilation during tinter and paint manufacture.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical in the pigment
product:
- When manually weighing and charging the mixing vessel, avoid generating dust.
- When filling containers and cleaning mixing equipment, prevent splashes and spills.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical in the pigment
product:
- Protective clothing covering arms and legs or equivalent
- Safety glasses
- Protective gloves
- Safety boots
- Respiratory protection when manually weighing and charging the mixing vessel.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? The following control measures should be implemented by the paint tinter
manufacturer to minimise environmental exposure during paint tinter manufacture:
- Ensure bunding is in-place.
- Do not use paint near drains or waterways.
Disposal
For Water based paints
? Wastes generated during industrial application should be disposed of through a
licensed waste contractor. Wastes generated during domestic use should be disposed
of according to the following instructions: "Do not pour leftover paint down the drain.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
23
Unwanted paint should be brushed out on newspaper, allowed to dry and then
disposed of via domestic waste collections. Empty paint containers should be left
open in a well-ventilated area to dry out. When dry, recycle steel containers via steel
can recycling programs. Disposal of empty paint containers via domestic recycling
programs may differ between local authorities. Check with your local council first."
For Solvent based paints
? Wastes generated during industrial application should be disposed of through a
licensed waste contractor. Wastes generated during domestic use should be disposed
of according to the following instructions: "Do not pour unwanted paint down the
drain. Keep unwanted paint in sealed containers for disposal via special chemical
waste collections. Empty paint containers should be left open in a well-ventilated area
to dry out. When dry, recycle steel containers via steel can recycling programs.
Disposal of empty paint containers via domestic recycling programs may differ
between local authorities. Check with your local council first."
Emergency procedures
Spills/release of the notified chemical should be handled by containment and either swept up
or an absorbent used if liquid, then placed in a sealable container ready for disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical;
- the notified chemical is introduced as an isolated chemical;
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
24
8 PUBLICATION SUMMARY REPORT
AZ-57-5328
Summary Report
Reference No: LTD/1121
PPG Industries Australia Pty Limited (ABN 82 055 500 939) of McNaughton Road, Clayton.
Victoria, 3168, has submitted a limited notification statement in support of their application
for an assessment certificate for AZ-57-5328. The notified chemical is intended to be used as
a component of mixture that is used in electrocoat resins to provide corrosion protection. Less
than one tonne of the notified chemical will be imported per annum for each of the first five
years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
- R41: Risk of serious eye damage
As a comparison only, the classification of notified chemical using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) is as Serious eye
damage/eye irritation (category I)-causes serious eye damage, and Chronic I-very toxic to
aquatic life with long lasting effects.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the intended manner.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R41: Risk of serious eye damage
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
25
? Use the following risk phrases for products/mixtures containing the notified chemical:
- > 10%: R41 Risk of serious eye damage
- 5% < conc < 10%: R36 Irritating to eyes
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical as introduced and as diluted for use:
- Enclosed electrocoating operation.
- Local exhaust ventilation during product transfer and electrocoating operation.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use:
- Protective gloves, safety glasses or goggles, industrial clothing and footwear
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
Disposal
? The solid residues of the notified chemical should be disposed of in hazardous waste
landfills in accordance with federal, State and local environmental control regulations.
? Empty containers should be recycled or disposed of through an approved waste
management facility.
Emergency procedures
? Spills/release of the notified chemical should be contained and prevented from
entering drains, streams or any water body.
? The spilled material should be collected with sand, vermiculite or other non-
combustible absorbent material and place in clean and suitable containers for disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
26
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum of notified chemical;
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated. However, due to the high
aquatic toxicity, if new uses with higher aquatic exposure are proposed, a separate risk
assessment may need to be carried out.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
27
9 PUBLICATION SUMMARY REPORT
AZ-53-1326
Summary Report
Reference No: LTD/1122
PPG Industries Australia Pty Limited (ABN 82 055 500 939) of McNaughton Road, Clayton.
Victoria, 3168, has submitted a limited notification statement in support of their application
for an assessment certificate for AZ-53-1326. The notified chemical is intended to be used as
a component of mixture that is used in electrocoat resins to provide corrosion protection. Less
than one tonne of the notified chemical will be imported per annum for each of the first five
years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
As a comparison only, the classification of notified chemical using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) is presented below. This
system is not mandated in Australia and carries no legal status but is presented for
information purposes.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as described.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical as introduced and as diluted for use:
- Enclosed electrocoating operation.
- Local exhaust ventilation during product transfer and electrocoating operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
28
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use:
- Protective gloves, safety glasses or goggles, industrial clothing and footwear
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
Disposal
? The solid residues of the notified chemical should be disposed of in accordance with
federal, State and local environmental control regulations.
? Empty containers should be recycled or disposed of through an approved waste
management facility.
Emergency procedures
? Spills/release of the notified chemical should be contained and prevented from
entering drains, streams or any water body.
? The spilled material should be collected with sand, vermiculite or other non-
combustible absorbent material and place in clean and suitable containers for disposal.
? Spilled material may be placed in a suitable container for later recycling.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical;
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
29
10 PUBLICATION SUMMARY REPORT
ZSR-20Be4
Summary Report
Reference No: LTD/1125
Ricoh Australia Pty Ltd of 8 Rodborough Rd Frenchs Forest NSW 2086 (ABN 30 000 593
171), and Lanier Australia Pty Ltd of 854 Lorimar St, Port Melbourne VIC 3207 (ABN 39
001 568 958) have submitted a joint limited notification statement in support of their
application for an assessment certificate for ZSR-20Be4. The notified polymer is intended to
be used as a component of photocopy toner. Up to three tonnes of the notified chemical will
be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer has a high molecular weight (NAMW >1000) and a low water
solubility indicating low potential to cross biological membranes. The notified polymer is
not considered to be hazardous.
The fine particles of the imported toner may cause mechanical irritation to the eyes, and to
the respiratory tract if inhaled. Repeated or prolonged skin contact may result in mild
irritation.
Based on the available data the notified polymer is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is negligible concern to public health when used in the intended manner.
Environmental Effects
On the basis of the PEC/PNEC ratio:
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
30
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? Service personnel and office staff should wear cotton or disposable gloves and ensure
adequate ventilation is present when removing spent cartridges containing the notified
polymer and during routine maintenance and repairs.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of to landfill.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
31
11 PUBLICATION SUMMARY REPORT
RAV 7 NG
Summary Report
Reference No: STD/1038
Sola International Holdings Ltd (ABN 47007719708) of Sherriffs Road, Lonsdale SA 5160,
has submitted a standard notification statement in support of their application for an
assessment certificate for RAV 7 NG. The notified polymer is intended to be used as a lens
casting monomer in the production of ophthalmic lenses. Ten to 100 tonnes of the notified
chemical will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
R22 Harmful if swallowed
R36/R38 Irritating to the eyes and skin
As a comparison only, the classification of notified polymer using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) (United Nations, 2003) is
categorised as Acute I.
Occupational Health and Safety
There is moderate concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is negligible concern to public health when used in the intended manner.
Environmental Effects
On the basis of the PEC/PNEC ratio:
The chemical is considered to pose a risk to the aquatic environment based on its reported use
pattern, and aqueous wastes from lens manufacturing should not be discharged to the sewer.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health, hazard classification for the notified chemical:
- R22 Harmful if swallowed
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
32
- R36/38 Irritating to eyes and skin
? Use the following risk and safety phrases for products/mixtures containing the
notified chemical:
- 25% R22 Harmful if swallowed
- R36/38 Irritating to eyes and skin
- S13 Keep away from food, drink and animal feeding stuffs
- S26 In case of contact with eyes, rinse immediately with plenty of water and seek
medical advice
- S28 After contact with skin, wash immediately with plenty of soap suds
- S 37 Wear suitable gloves
- S 39 Wear eye/face protection
- 5% R36/38 Irritating to eyes and skin
S26 In case of contact with eyes, rinse immediately with plenty of
water and seek medical advice
S28 After contact with skin, wash immediately with plenty of soap
suds
S37 Wear suitable gloves
S 39 Wear eye/face protection
- 1% S24/25 Avoid contact with skin and eyes
? Suppliers should label the notified chemical with the signal word `Hazardous' and the
risk phrases listed above.
Health Surveillance
? The notified chemical should be considered by NOHSC for development of health
surveillance guidelines.
? As the notified chemical is a skin irritant and analogue material has been shown to
cause irritant contact dermatitis, employers should carry out health surveillance for
any worker who has been identified in the workplace risk assessment as having a
significant risk of irritant contact dermatitis.
Control Measures
Occupational Health and Safety
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical:
- Protective clothing
- Chemically resistant gloves or gauntlets
- Chemical goggles or safety glasses
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
33
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? Do not allow material or rinsates from lens manufacturing equipment to enter drain,
sewers or water course.
Disposal
? The notified chemical should be disposed of to landfill or be incinerated
Emergency procedures
? Spills/release of the notified chemical should be handled by diking area to contain
spill. Recover neutralised material on adsorbents, such as sand or vermiculite, and
sweep into closed containers for disposal. If area of spill is porous, remove as much
earth and gravel, etc. as necessary and place in closed containers for disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical;
- when further toxicological studies are available; or
Existing studies on repeated dose toxicity (14 days) are not sufficient. The submitted test
plan recommends conductance of a repeated dose toxicity study of a 90-day duration, which
will incorporate toxicity to reproductive organs. Additionally, studies on stability in water,
chromosomal toxicity are also to be performed. These studies are to be supplied as part of a
secondary notification for this polymer.
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
34
12 PUBLICATION SUMMARY REPORT
Z-38
Summary Report
Reference No: EX/47
Lubrizol International, Inc. (ACN 002 747 944) of 28 River Street, Silverwater, NSW 2128
has submitted a limited notification statement in support of their application for an
assessment certificate for Z-38. The notified polymer is intended to be used as a gasoline
additive. Less than 1 000 tonnes of the notified chemical will be imported per annum for each
of the first five years.
Since granting of the abovementioned Assessment Certificate, 3M Australia Pty Ltd (ACN
000 100 096) of 2-74 Dunheved Circuit, St Marys, NSW 2760 has submitted a notification
statement in support of their application for an extension of the original Assessment
Certificate for Z-38. Lubrizol International Inc. has agreed to this extension.
Information submitted by 3M Australia Pty Ltd pertains to the introduction of the notified
chemical for use in an aerosol-cleaning product for automotive engines. Introduction volumes
will be up to 100 kg per year, imported as the finished product.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Z-38 was of very low acute oral toxicity in rats and was a slight to moderate skin irritant in
rabbits. A 50% solution of Z-38 in petroleum naphtha was a slight to moderate eye irritant in
rabbits. The notified polymer cannot be determined to be a hazardous substance on the basis
of the limited data provided, under the NOHSC Approved Criteria for Classifying Hazardous
Substances. However, the Material Safety Data Sheet (MSDS) and label for Z-38 and the
additive package Lubrizol 9566 contain the risk phrase: May cause sensitisation by skin
contact, on the basis of data from similar substances.
The notifier has indicated that a typical additive package in which the notified polymer may
be imported contains 42% petroleum naphtha including 17% trimethylbenzene isomers, 3.2%
xylene, 2.1% cumene. According to NOHSC List of Designated Hazardous Substances, the
additive package may cause lung damage if swallowed as a result of the petroleum naphtha
content and is harmful if inhaled and irritating to eyes, respiratory and skin as a result of the
trimethylbenzene isomer content. The additive package also should be considered flammable
as a result of the trimethylbenzene isomer content.
Occupational Health and Safety
The notified chemical is to be imported at up to 50% in an end use additive product Lubrizol
9566. During import and transport of the notified polymer, worker exposure to the notified
polymer is unlikely except in the event of a spill. Exposure after a spill would be controlled
by use of the recommended practices for spillage clean up outlined in the MSDS supplied by
the notifier.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
35
At refineries and terminals, the handling of fuel additive packages may cause slight to
moderate eye irritation and slight to moderate skin irritation from exposure to the notified
polymer if adequate precautions are not taken. The solvent content can cause toxic effects via
inhalation and eye, skin and respiratory irritation. Trimethylbenzene has a NOHSC exposure
standard of 25 ppm and cumene, 50 ppm and xylene 80 ppm (TWA). Employers are
responsible for maintaining workplace airborne concentrations below these limits. The
MSDS for Lubrizol 9566 recommends that workers wear a faceshield and protective apron
and use nitrile or neoprene gloves and boots to control exposure. Respiratory protection (full
face respirator) is recommended if exposure limits are exceeded and self-contained breathing
apparatus for entry into confined spaces, poorly ventilated areas or large spill clean-up sites.
Engineering controls and personal protective equipment for handling the solvent components
of the additive package are sufficient to limit exposure to the notified polymer.
The use of automatic, dedicated transfer lines and enclosed, automated injection into fuel will
reduce the likelihood of exposure to the additive package. Therefore, the health risk expected
for refinery and terminal workers would be assessed as low.
Tanker drivers, service station workers and mechanics will receive negligible exposure to the
notified polymer because of the very low concentration (0.0085 ?0.017%) present in the final
fuel. Therefore, the risk of adverse health effects for these workers arising from exposure to
the notified polymer is negligible.
Given the low volume of automotive aerosol-cleaning product imported and the low
concentration of notified polymer in the product, the health risk to workers from this use is
low.
Public Health Effects
Public exposure to the notified polymer will predominantly occur from inhalation, dermal
and, to a lesser extent, ocular and oral exposure when refuelling vehicles and/or the filling of
petrol containers for domestic use at petrol stations and where treated gasoline is used for the
cleaning of equipment or parts by a home mechanic. The notified polymer is a slight to
moderate eye irritant, but is present at low concentrations in petrol (0.0085 ?0.017%).
Consequently, the irritant risk to the public is likely to be no greater than that of untreated
petrol. The potential risk to the public from storage, transport, formulation and commercial
operations is considered to be low.
Given the low volume of automotive aerosol-cleaning product imported and the low
concentration of notified polymer in the product, the health risk to the public from this use is
low.
Environmental Effects
The environmental hazard from the notified polymer is low when it is blended into petrol and
used in the manner indicated by the notifier.
There is little potential for significant release of the notified polymer during blending
operations which will be performed at dedicated petrochemical facilities. A maximum of 10
tonnes of the material may be released each year as a result of cleaning the iso containers, and
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
36
most of this is expected to be recovered in waste sludge and incinerated or placed into
landfill.
Some release is inevitable as a result of petrol spills during distribution to motorists. Release
is estimated as a maximum of 10 tonnes per annum and will be widespread and very diffuse.
Although no specific information is available, it is probable that the notified polymer is
ultimately biodegradable. It has a low water solubility and the high hydrocarbon content is
expected to result in a high affinity for the organic component of soils and sediments (log Pow
> 6.2). Any material released to the soil compartment (eg. from petrol spills) would associate
with the organic component of the soil, and is expected to be slowly mineralised to water and
oxides of carbon and nitrogen through biological processes. The same fate is expected for any
polymer placed into landfill in waste sludge from refineries.
The notified polymer will be used as a component of engine deposit control additives for non
leaded petrol. There is considerable evidence that modern motor vehicles running on fuel
containing these additives show significant improvements in exhaust emission of
hydrocarbons, CO and NOx compared with vehicles using un-supplemented fuel. However,
the formation and control of engine deposits, and effects on fuel combustion efficiency and
on the composition of exhaust emissions is a very complex subject. Factors influencing
engine operating parameters may include the composition of the base fuel (eg. presence/
absence of olefins) and the presence and concentration of control additives in the fuel.
Nevertheless, the available evidence suggests that the use of the notified polymer as a fuel
additive has no significant deleterious effects on the quality or quantity of noxious or toxic
vehicular exhaust emissions, and the use of the polymer as intended is probably beneficial
and not pose a hazard to the environment.
The majority of the notified polymer is expected to be completely destroyed by combustion
within the engine, resulting in oxides of carbon, nitrogen and water vapour.
Ecotoxicity data only was provided for green algae, and the results provided a 72-hour EbL50
of 39 mg/L nominal Water Accomodated Fraction (WAF) and 96-hour NOEL of 25 mg/L,
indicating that the polymer shows some toxicity to this species. However, except in the case
of a transport accident, release to the water compartment is unlikely and the high
octanol/water partition coefficient indicates that if released to the soil or water compartments
the polymer would be expected to bind to, and associate with the organic component of soils
and sediments. This will mitigate any toxic potential of the material. Bioaccumulation is
considered to be unlikely.
RECOMMENDATIONS
To minimise occupational exposure to the notified polymer, the following guidelines and
precautions should be observed:
Spillage of the notified polymer should be avoided. Spillage should be cleaned up
?br>
promptly with absorbents which should be put into containers for disposal;
Good personal hygiene should be practised to minimise the potential for ingestion;
?br>
A copy of the MSDS should be easily accessible to employees.
?br>
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
37
Safety goggles, chemical resistant industrial clothing including an apron and footwear and
impermeable gloves (nitrile or neoprene) should be used during occupational use of the
additive packages containing the notified polymer; where engineering controls and work
practices do not reduce vapour and particulate exposure to safe levels, an air fed respirator
should also be used.
Guidance in selection of goggles may be obtained from Australian Standard (AS)
?br>
1336 and Australian/New Zealand Standard (AS/NZS) 1337; for industrial clothing,
guidance may be found in AS 3765.2; for impermeable gloves or mittens, in AS
2161.2; for occupational footwear, in AS/NZS 2210; for respirators, in AS/NZS 1715
and AS/NZS 1716. Other internationally accepted standards may also be used in the
selection and use of PPE.
If products containing the notified polymer are hazardous to health in accordance with the
NOHSC Approved Criteria for Classifying Hazardous Substance, workplace practices and
control procedures consistent with State and territory hazardous substances regulations must
be in operation.
Employers should ensure that NOHSC exposure standards for all components of additive
packages are not exceeded in the workplace.
The notified polymer will need to be tested to ensure that it will meet the criteria in the
upcoming Australian Standard, Evaluation of Devices and Additives which Claim to Improve
Vehicle Performance, to be AS 4430.2.
Secondary Notification
The NICNAS Director must be notified in writing within 28 days by the notifier, other
importer or manufacturer:
Under Section 64(1) of the Act:
- if more than 20 tonnes/year of the notified chemical is to be introduced, due to the
narrow safety margin for algae data on the likely extent of adsorption to sludge
and sediment may be requested.
Under Section 64(2) of the Act:
- if any of the circumstances listed in this subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
38
13 PUBLICATION SUMMARY REPORT
Fluorochemical Urethane
Summary Report
Reference No: PLC/384
3M Australia Pty Ltd (ABN: 90 000 100 096) 2 ?74 Dunheved Circuit, St Mary NSW 2670
has submitted a synthetic polymer of low concern (PLC) notification statement in support of
their application for an assessment certificate for Fluorochemical urethane. The notified
polymer is a component in a retail carpet treatment which will be imported in a ready to use
form. Up to 3 tonnes of the notified polymer will be imported per annum for each of the first
five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer as introduced in an aqueous formulation meets the PLC criteria and can
therefore be considered to be of low hazard.
The notified polymer is not classifiable based on the results of the acute inhalation study
submitted.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Low Concern to public health when used in an appropriate manner as set out in the
product guidelines.
Environmental Assessment
There are significant uncertainties surrounding the behaviour of fluorocarbon compounds in
general in the environment in areas of partitioning behaviour, degradation, chronic toxicity
and bioaccumulation, and the potential environmental impact of the breakdown product
perfluorobutane sulfonate.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
39
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of through incineration at an approved
hazardous waste incinerator with the proper controls for HF or to landfill.
Emergency procedures
? Spills/release of the notified polymer should be contained, collected and placed in an
approved closed container along with depressurised can.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
- the notifier become aware of information pertaining to the environmental fate or
toxicity of perfluorobutane sulfonate (PFBS) the notifier should make this
information available to NICNAS. This should include data which becomes
available under the US EPA consent order
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
40
14 PUBLICATION SUMMARY REPORT
Resydrol AY 586w/45WA
Summary Report
Reference No: PLC/400
Pacific Resins (ABN 92 520 305 379) 2/9 Jannali Ave Jannali NSW 2226 has submitted a
synthetic polymer of low concern (PLC) notification statement in support of their application
for an assessment certificate for Polymer in Resydrol AY 586w/45WA. The notified polymer
is intended to be used as a component of industrial waterborne coatings. Twenty tonnes of the
notified polymer will be imported in the first year rising to 100 tonnes per annum by the fifth
year.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as a photocopier toner.
Environmental Assessment
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
41
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of in accordance with government
regulations for the disposal of specific waste via a licensed waste disposal contractor
to a regulated landfill or incinerator.
Emergency procedures
? Spills/release of the notified polymer should be handled by collecting mechanically or
with binding material (e.g. sand and sawdust) and flushing the spill area with water.
? Large spills should be contained with dikes and material should be transferred to
suitable containers for disposal.
? Prevent the material from entering drains or water courses.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
42
15 PUBLICATION SUMMARY REPORT
Polymer in Emulsion EXP-3913
Summary Report
Reference No: PLC/402
Rohm and Haas Australia Pty Ltd of 4th Floor, 969 Burke Rd Camberwell VIC 3124 (ACN
29 004 513 188) has submitted a synthetic polymer of low concern (PLC) notification
statement in support of their application for an assessment certificate for Polymer in
Emulsion EXP-3913. The notified polymer is intended to be used as a pressure-sensitive
adhesive for labels. Up to 300 tonnes of the notified chemical will be imported per annum for
each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is negligible concern to public health when used in the manner proposed.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
No specific engineering controls, work practices or personal protective equipment are
?br>
required for the safe use of the notified polymer itself, however, these should be selected
on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
43
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of by landfill or be incinerated.
Storage
? Keep from freezing; material may coagulate. The minimum and maximum
temperatures recommended for storage are 1 and 49篊 respective.
Emergency procedures
? Keep spectators away. Floor may be slippery; use care to avoid falling. Contain spills
immediately with inert materials (eg sand, earth). Transfer liquids and solid diking
material to separate suitable containers for recovery or disposal. Keep spills and
cleaning runoff out of municipal sewers and open bodies of water.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
44
16 PUBLICATION SUMMARY REPORT
Aristoflex AVC
Summary Report
Reference No: PLC/411
Clariant (Australia) Pty Ltd (ABN 30 069 435 552) of Warrigal Road, Chadstone VIC 3148;
and Trimex Pty Ltd (40 001 198 787) of 5 Crewe Place, Rosebery NSW 2018, have
submitted a joint synthetic polymer of low concern (PLC) notification statement in support of
their application for an assessment certificate for Aristoflex AVC. The notified polymer will
be used a gelling agent for aqueous systems and as a texturiser, thickener for oil-in-water
emulsions. Less than five tonnes of the notified chemical will be imported per annum for
each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. The powder may cause irritation to the eyes and repeated or prolonged skin contact
may result in mild irritation. A small fraction of the polymer particles are in the inspirable
range and mechanical irritation to the respiratory tract may occur if inhaled.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is low concern to public health when used in the intended manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern and PEC/PNEC ratio.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
45
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of by incineration or landfill in accordance
with State/Territory waste management regulations. Product containing the notified
polymer should be disposed of to sewer.
Emergency procedures
? Spills/release of the notified polymer should be handled by sweeping and placing
spilled powder in sealed container for disposal. Do not allow entry to stormwater
drains or waterways.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
46
17 PUBLICATION SUMMARY REPORT
Silicon Polyamide
Summary Report
Reference No: PLC/422
Dow Corning Australia Pty Ltd of Macquarie University Research Park, 3 Innovation Road,
North Ryde, NSW 2113 (ABN 36 008 444 166).has submitted a synthetic polymer of low
concern (PLC) notification statement in support of their application for an assessment
certificate for Silicon polyamide. The notified polymer will be used in colour cosmetics, skin
care, sun care and hair care products. Up to one tonne of the notified polymer will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. The MSDS for the imported product 2-8178 Gellant indicates that direct contact with
the eyes may cause mild irritation.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is low concern to public health when used in the intended manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
47
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should ultimately be disposed of by landfill.
Emergency procedures
? The MSDS indicates that if diked material can be pumped, stored recovered material
in appropriate container. Wipe up or scrape up and contain for salvage or disposal.
Materials in contact with water, moisture, acids or bases have the potential to generate
hydrogen gas. Recovered material should be stored in vented container. Clean area as
appropriate since some silicone material, even in small quantities, may present a slip
hazard. Final cleaning may require the use of steam, solvent or detergents. Dispose of
saturated absorbent or cleaning materials appropriately, since spontaneous heating
may occur.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
48
18 PUBLICATION SUMMARY REPORT
Scaleguard 60116
Summary Report
Reference No: PLC/424
ONDEO Nalco Australia Pty Ltd of 3 Anderson St Banksmeadow NSW (ACN 41 000 424
788) has submitted a synthetic polymer of low concern (PLC) notification statement in
support of their application for an assessment certificate for Scaleguard 60116. The notified
polymer will be used in pulp and paper milling processes. Up to 120 tonnes of the notified
chemical will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. However, the MSDS indicates that the notified polymer is a slight skin and eye
irritant.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is negligible concern to public health when manufactured and used in the proposed
manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? It is recommended that products containing more than 20% notified polymer carry the
following safety directions on the label:
- S24/25 Avoid contact with skin and eyes
- S 37/39Wear suitable gloves and wear eye/face protection
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
49
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of in an approved incinerator or waste
treatment/disposal site in accordance with all applicable regulations.
? Do not dispose of wastes in local sewer or with normal garbage.
? Triple rinse (or equivalent) all containers and recycle, recondition or puncture and
dispose of in a sanitary landfill or by other procedures approved by State and local
authorities.
Emergency procedures
? Smalls spills/release of the notified polymer should be soaked up with absorbent
material. Place residues in a suitable, covered, properly labelled container and wash
the affected area.
? Large spills should be handled by containing the liquid using absorbent material, by
digging trenches or by diking. Reclaim into recovery or salvage drums or tank truck
for proper disposal. Clean contaminated surfaces with water or aqueous cleaning
agent. Contact an approved waste hauler for disposal of contaminated recovered
material.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
50
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
51
19 PUBLICATION SUMMARY REPORT
ABS Copolymer Resin
Summary Report
Reference No: PLC/429
Dow Chemical (Australia) Ltd (ABN 72 000 264 979) of 541-583 Kororoit Creek Road,
Altona VIC 3018 has submitted a synthetic polymer of low concern (PLC) notification
statement in support of their application for an assessment certificate for ABS Copolymer
Resin. The notified polymer is intended to be used as a structural thermoplastic for the
manufacture of articles including consumer goods, appliances and automotive parts. Up to
500 tonnes of the notified chemical will be imported per annum for each of the first five
years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used to produce the components and
articles described.
Environment
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? The following personal protective equipment is recommended in accordance with
good occupational health and safety practice
- Protective glasses and clean, body-covering clothing
- In dusty or misty atmospheres, use an approved particulate respirator
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? It is recommended that management conducts a workplace risk assessment to confirm
that concentrations of nuisance dust/ decomposition products are adequately
controlled during formulation and moulding/ extrusion of the notified polymer.
? A copy of the MSDS should be easily accessible to employees.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
52
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of by licenced waste contractor in an
approved landfill
Storage
? The following precautions should be taken by distributors and product end-users
regarding storage of the notified polymer:
- Store in a dry area at ambient temperature
- Electrically ground storage silos to prevent buildup of static charges (dust explosion
risk)
Emergency procedures
? Spills/release of the notified polymer should be handled by
- containing the spilled material (pellets or beads may present a slipping hazard)
- collecting material in a container for reuse or disposal
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
53
20 ACCESS TO FULL PUBLIC REPORT
NICNAS publishes a Full Public Report for each new chemical assessed. These reports are
available for public inspection at the library of the National Occupational Health & Safety
Commission at their Canberra office by appointment only. Please call the library on (02)
6279 1161 or (02) 6279 1163 to arrange to view the Full Public Report.
Reports can also be viewed and downloaded free of charge from our website at
www.nicnas.gov.au. Copies of these reports may also be requested, free of charge, by
contacting the Administration Section of NICNAS by phone: (02) 8577 8816 or fax: (02)
8577 8888.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
54
21 LOW VOLUME CATEGORY PERMITS
The permits listed in Table 2 were issued to import or manufacture the following chemicals
under section 21U of the Industrial Chemicals (Notification and Assessment) Act 1989. Low
Volume Category Permits are approved for 36 months.
Table 1
Low Volume Category Permits
PERMIT COMPANY COMPANY CHEMICAL OR TRADE HAZARDOUS USE DATE
NUMBER NAME POSTCOD NAME SUBSTANCE
E
590 Epson 2113 MJA-549(N) Yes Printing Ink 17.12.03
Australia Pty
Ltd
591 Kodak 3058 B-21825 No Printing 13.01.04
(Australasia)
Pty Ltd
592 Unilever 2151 Dodecanoic acid, 2- Yes Cosmetic 13.01.04
Australia Ltd (1-carboxyethoxy)-1-
methyl-2-oxoethyl,
sodium salt
593 Unilever 2151 Decanoic acid, 2-(1- Yes Cosmetic 13.01.04
Australia Ltd carboxyethoxy)-1-
methyl-2-oxyethyl,
sodium salt
594 Jurlique 5251 Dodecanoic acid, No Cosmetic 13.01.04
International monoester with
Pty Ltd decaglycerol
595 Henkel 2128 TMAS Yes Mould 15.01.04
Australia Pty release
Ltd agent
596 Kodak 3058 Pentanoic acid, 5,5'- ND Photography 15.01.04
(Australasia) [dithiobis(4,1-
Pty Ltd phenyleneimino)]bis[
5-oxo-, disodium salt
N.D.: not determined; insufficient data available to effect a health effects classification under
Approved Criteria [NOHSC:1008(1999)]
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
55
22 EARLY INTRODUCTION PERMITS FOR NON-HAZARDOUS INDUSTRIAL
CHEMICALS
The permits listed in Table 3 were issued to import or manufacture the following chemicals
prior to the issue of their respective assessment certificates under section 30A of the Act.
Table 2
Early Introduction Permits
PERMIT COMPANY CHEMICAL OR USE
NUMBER NAME TRADE NAME
310 Unilever Acrylates/palmeth-25 Cosmetic
Australia Ltd Acrylate Copolymer
311 Dow Corning Vinyl Crosspolymer in Paper coating
Australia Dow Corning 27751
312 DuPont DP7007 Surface coating
(Australia)
Ltd
313 DuPont DP2009 Surface coating
(Australia)
Ltd
314 Swift & Uralac Surface coating
Company ZW/5209P/ZW5210P
Limited
315 International Polymer in Rheolate 450 Surface coatings
Sales &
Marketing Pty
Ltd
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
56
23 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE AUSTRALIAN
INVENTORY OF CHEMICAL SUBSTANCES FIVE YEARS AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 14(1) of the Industrial Chemicals (Notification
and Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 3
Chemicals Eligible for Listing on the Australian Inventory of Chemical Substances
CHEMICAL NAME CAS MOLECULAR
NUMBER FORMULA
Acetic acid, cyano-, reaction products with 124358-45-8 Unspecified
10-undecenal
Phosphorothioic acid, O,O,O-triphenyl 192268-65-8 Unspecified
esters, tert-Bu derivs.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
57
24 LOW REGULATORY CONCERN CHEMICALS REFORM INITIATIVE
Following the publication of the Final Report and Recommendations for NICNAS Low
Regulatory Concern Chemicals (LRCC) Reform Initiative and the Implementation Strategy
for NICNAS Low Regulatory Concern Chemicals (LRCC) Reform Initiative, various
amendments to the Industrial Chemicals (Notification and Assessment) Act 1989 (the Act) are
proposed, as detailed in the draft Industrial Chemicals (Notification and Assessment)
Amendment (Low Regulatory Concern Chemicals) Bill 2004 (the draft Bill).
The amendments to the Act are necessary to:
? increase the range of exemption categories currently available under the Act, e.g.,
transhipment, export only, and increase permissible volumes for research and
development;
? streamline permit renewal processes;
? increase the range of permits and assessment certificates for low risk, low hazard
chemicals;
? introduce audited self-assessment for industry, modular assessment and controlled
use;
? enhance existing compliance provisions, including enhancing the Director's power to
require information and corresponding increases in relevant penalties;
? enable optional immediate listing of an assessed chemical onto the Australian
Inventory of Chemicals Substances;
? introduce mandatory registration for all introducers;
? harmonise the definition of `cosmetics' with the definition in the Trade Practices
(Consumer Product Information Standards) (Cosmetics) Regulations 1991.
NICNAS intends to make the draft Bill available to stakeholders for comment. At this stage
it is expected that the draft Bill will be available on the NICNAS website www.nicnas.gov.au
in early February 2004.
Comments in relation to the draft Bill will be accepted until COB Friday 27 February 2004.
Please submit comments by email to louise.seery@nicnas.gov.au or by post to NICNAS,
GPO Box 58 Sydney NSW 2001.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
58
25 NOTICE OF PUBLICATION OF SODIUM ALKYLBENZENE SULFONATE
ANTI-VALVE SEAT RECESSION ADDITIVE SUMMARY REPORT
The industrial chemical, Sodium Alkylbenzene Sulfonate Anti-Valve Seat Recession
Additive, has been assessed as a priority existing chemical (PEC) under the Commonwealth
Industrial Chemicals (Notification and Assessment) Act, 1989 (the Act), as amended.
No applications for variations to the draft public report were received. Comments of an
editorial nature were received and the report was amended accordingly.
An assessment report (PEC Report No.26) has been published under section 60F of the Act
and is available from the NICNAS website at:
http://www.nicnas.gov.au/publications/car/pec/pecindex.htm.
The summary report has been prepared in accordance with subsection 60F(4) of the Act, and
is published here.
The publication of this report revokes the declaration of Sodium Alkylbenzene Sulfonate
Anti-Valve Seat Recession Additive as a priority existing chemical under section 62 of the
Act.
Reports are also available (free) on request to:
NICNAS
GPO Box 58
Sydney NSW 2001
Australia
Toll free 1800 638 528
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
59
SUMMARY REPORT OF SODIUM ALKYLBENZENE SULFONATE
ANTI-VALVE SEAT RECESSION ADDITIVE
Chemical Identity
Chemical Name: Benzenesulfonic acid, mixed mono- and di-C15-30-alkyl derivatives,
sodium salts
CAS No.: 78330-12-8
Chemical Name (generic) Sodium alkylbenzene sulfonate
Applicant
Morey Oil South Pacific (Australia) Pty Ltd
PO Box 1033
Archerfield, Queensland 4108
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
60
26 AICS ONLINE TRAINING
The non-confidential section of the Australian Inventory of Chemical Substances (AICS) is
now on the NICNAS web site.
Companies can still request NICNAS to search the non-confidential AICS, however fees will
be introduced for this service in March/ April 2004.
NICNAS is organising free training sessions in Sydney and Melbourne for those who want to
know about AICS and how to search the web version. These sessions will run approximately
2 hours and include examples, searching tips, troubleshooting and hands-on training.
Training Session Details
SYDNEY - Tuesday February 17 & Wednesday February 25
9.30 ?11.30am ......12 noon - 2pm .......2.30 ?4.30pm
ALL FEBRUARY SESSIONS ARE FULLY BOOKED
MELBOURNE ?Wednesday February 18 & Thursday February 19
9.30 ?11.30am ......12 noon - 2pm .......2.30 ?4.30pm
Venues
SYDNEY - Boardroom, NICNAS Office; 334-336 Illawarra Rd, Marrickville
MELBOURNE - Department of Health and Ageing, Computer Training Suite; Level 7, 2
Lonsdale Street, Melbourne
Further sessions are being organised for March 2004. If you would like to
attend, please contact Michelle Jacobs on 02 8577 8820 or
michelle.Jacobs@nicnas.gov.au.
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
61
27 CALL FOR INFORMATION ON CHEMICALS
The Director of the National Industrial Chemicals Notification and Assessment
Scheme (NICNAS) is seeking information, under section 48 of the Industrial
Chemicals (Notification and Assessment) Act 1989 (the Act), on the chemicals listed below.
These industrial chemicals are of interest because of potential human health and/or
environment concerns. These chemicals are also being considered in terms of the adequacy
of public health controls for their industrial and/or domestic uses.
Chemical Name CAS Number
Butyric Acid 107-92-6
Chloroform 67-66-3
Cobalt chloride 7646-79-9
Cobalt chloride, hexahydrate 7791-13-1
Cobalt nitrate 10141-05-6
Cobalt nitrate, hexahydrate 10026-22-9
Carbon monoxide 630-08-0
Molybdenum compounds 7439-98-7
Nitromethane 75-52-5
Sodium azide 7631-99-4
The specific information sought on the chemicals is:
quantities of each chemical imported into and/or manufactured in Australia in the
?br>
calendar year 2002 and 2003;
uses of the chemicals.
?br>
The notice is directed to all persons who have manufactured or imported one or more
of the chemicals or products since January 2002. Any other persons with information on
these chemicals including users, past importers or manufacturers are also encouraged to
provide information on the chemicals to the Director.
In accordance with section 50 of the Act, the information may be accompanied by an
application that some or all of the information provided be treated as exempt information.
Application forms are available on the NICNAS web-site at www.nicnas.gov.au or may be
obtained from Ms Virginia Parish on (02) 8577 8895 or email virginia.parish@nicnas.gov.au
Closing date for the provision of information is 2 March 2004. Data should be sent to:
NICNAS, GPO Box 58, Sydney 2001.
If you would like further information or wish to discuss any aspects of this activity please
contact Dr Sneha Satya on 02 8577 8880, email sneha.satya@nicnas.gov.au or Ms Virginia
Parish: phone (02) 8577 8893, fax (02) 8577 8888, email virginia.parish@nicnas.gov.au
Chemical Gazette Commonwealth of Australia Gazette
No. C 2, 3 February 2004
|