Full Public Report format
File No: STD/1274
09 September 2008
NATIONAL INDUSTRIAL CHEMICALS NOTIFICATION AND ASSESSMENT SCHEME
(NICNAS)
FULL PUBLIC REPORT
GTL Naphtha
This Assessment has been compiled in accordance with the provisions of the Industrial Chemicals (Notification and
Assessment) Act 1989 (Cwlth) (the Act) and Regulations. This legislation is an Act of the Commonwealth of Australia.
The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) is administered by the Department
of Health and Ageing, and conducts the risk assessment for public health and occupational health and safety. The
assessment of environmental risk is conducted by the Department of the Environment, Water, Heritage and the Arts.
For the purposes of subsection 78(1) of the Act, this Full Public Report may be inspected at our NICNAS office by
appointment only at 334-336 Illawarra Road, Marrickville NSW 2204.
This Full Public Report is also available for viewing and downloading from the NICNAS website or available on
request, free of charge, by contacting NICNAS. For requests and enquiries please contact the NICNAS Administration
Coordinator at:
Street Address: 334 - 336 Illawarra Road MARRICKVILLE NSW 2204, AUSTRALIA.
Postal Address: GPO Box 58, SYDNEY NSW 2001, AUSTRALIA.
TEL: + 61 2 8577 8800
FAX + 61 2 8577 8888
Website: www.nicnas.gov.au
Director
NICNAS
TABLE OF CONTENTS
FULL PUBLIC REPORT.............................................................................................................................................. 3
1. APPLICANT AND NOTIFICATION DETAILS ................................................................................... 3
2. IDENTITY OF CHEMICAL ................................................................................................................... 3
3. COMPOSITION ...................................................................................................................................... 3
4. PHYSICAL AND CHEMICAL PROPERTIES ...................................................................................... 4
5. INTRODUCTION AND USE INFORMATION..................................................................................... 4
6. HUMAN HEALTH IMPLICATIONS..................................................................................................... 5
7. ENVIRONMENTAL IMPLICATIONS .................................................................................................. 9
8. CONCLUSIONS AND REGULATORY OBLIGATIONS .................................................................. 11
APPENDIX A: PHYSICAL AND CHEMICAL PROPERTIES........................................................................................... 15
APPENDIX B: TOXICOLOGICAL INVESTIGATIONS................................................................................................... 18
BIBLIOGRAPHY...................................................................................................................................................... 22
Created on 19/06/2008 3:37 PM Last Saved 9/09/2008 2:42 PM
09 September 2008 NICNAS
FULL PUBLIC REPORT
GTL Naphtha
1. APPLICANT AND NOTIFICATION DETAILS
APPLICANT(S)
Sasol Chevron Consulting Limited (ABN: 46 096 439 404)
Level 15, QV1 Building, 250 Georges Terrace
Perth WA 6000
The Shell Company of Australia Limited (ABN: 46 004 610 459)
8 Redfern Road
East Hawthorn, VIC 3123
NOTIFICATION CATEGORY
Standard: Chemical other than polymer (more than 1 tonne per year).
EXEMPT INFORMATION (SECTION 75 OF THE ACT)
Data items and details claimed exempt from publication: Chemical name, other names, CAS number,
molecular formula, structural formula, molecular weight, spectral data, import volume, the identity of the
manufacturer and the identity of analogues.
VARIATION OF DATA REQUIREMENTS (SECTION 24 OF THE ACT)
Variation to the schedule of data requirements is claimed as follows: biodegradation, bioaccumulation, acute
toxicity to fish, acute toxicity to aquatic invertebrates, algal growth inhibition, acute dermal toxicity, acute
inhalation toxicity, eye irritation, skin irritation, skin sensitisation, repeated-dose toxicity and in vitro
chromosomal aberration.
PREVIOUS NOTIFICATION IN AUSTRALIA BY APPLICANT(S)
None
NOTIFICATION IN OTHER COUNTRIES
United States of America, Canada, Korea and the European Union
2. IDENTITY OF CHEMICAL
MARKETING NAME(S)
GTL Naphtha
F-T Naphtha
MOLECULAR WEIGHT
< 500 Da
ANALYTICAL DATA
Reference NMR and IR spectra were provided.
3. COMPOSITION
The notified chemical is a complex mixture of hydrocarbons with a high paraffinic content. The notified
chemical contains hexane at a concentration between 5 and 20%.
FULL PUBLIC REPORT: STD/1274 Page 3 of 23
09 September 2008 NICNAS
4. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE AT 20篊 AND 101.3 kPa: Clear, colourless liquid
Property Value Data Source/Justification
<-20oC
Melting Point/Freezing Point Measured
62-181oC at 100.8 kPa
Boiling Point Measured
701 kg/m3 at 20oC Measured
Density
0.98 cSt (9.8 ?10-7 m2/s) at 40oC Provided by notifier, source not
Viscosity
specified.
4.4 kPa at 25oC Measured
Vapour Pressure
Water Solubility <1 mg TOC/L at 20 ?.5癈 Measured
Hydrolysis as a Function of pH Not determined. The notified chemical does not contain
hydrolysable functionality.
log POW = 4.40 to >6.50 at 20癈 Measured
Partition Coefficient
(n-octanol/water)
log Koc = 2.05 to >5.63 Measured
Adsorption/Desorption
Dissociation Constant Not determined. No acid or base groups are present and
the water solubility is very low.
-18oC at 101.3 kPa Measured
Flash Point
Flammability Upper: 6% Provided by notifier, source not
Lower: 1% specified.
256oC Measured
Autoignition Temperature
DISCUSSION OF PROPERTIES
For full details of tests on physical and chemical properties, please refer to Appendix A.
The value given for the viscosity indicates that the notified chemical meets the criterion for classification as a
aspiration hazard (ie < 7 ?10-6 m2/s). Therefore, the notified chemical is classified as hazardous (with risk
phrase R65 Harmful: May cause lung damage if swallowed) under the Approved Criteria for Classifying
Hazardous Substances [NOHSC:1008(2004)].
Reactivity
Expected to be stable under normal conditions of use. However, it is highly flammable and is expected to burn
vigorously if involved in a fire.
Dangerous Goods classification
Based on the available data the notified chemical is classified as follows according to the Australian Dangerous
Goods Code (FORS, 1998): Class 3 Flammable Liquid; packaging group II
5. INTRODUCTION AND USE INFORMATION
MODE OF INTRODUCTION OF NOTIFIED CHEMICAL (100%) OVER NEXT 5 YEARS
The notified chemical will not be manufactured in Australia.
MAXIMUM INTRODUCTION VOLUME OF NOTIFIED CHEMICAL (100%) OVER NEXT 5 YEARS
Year 1 2 3 4 5
Tonnes 30,000-100,000 30,000-100,000 30,000-100,000 30,000-100,000 30,000-100,000
PORT OF ENTRY
The notified chemical will be imported through major ports throughout Australia, including but not limited to
Sydney, Melbourne, Adelaide and Perth.
IDENTITY OF RECIPIENTS
Australian ethylene producers.
TRANSPORTATION AND PACKAGING
The notified chemical will be transported by ship, barge or rail car and off loaded to an on-site storage tank at
an appropriate ethylene cracker site.
FULL PUBLIC REPORT: STD/1274 Page 4 of 23
09 September 2008 NICNAS
USE
The notified chemical will be used as a feedstock in ethylene crackers for the production of polyethylene and
alpha-olefins.
OPERATION DESCRIPTION
Once the notified chemical has been transported to an ethylene cracker site hoses will be connected to the
transport tank and it will be off loaded into on-site storage tanks. A vacuum back flush system will remove
the notified chemical from the unloading hoses, which will be further automatically capped on removal to
prevent spillage. The few grams of notified chemical that may reside on the surface of the hoses will be
allowed to evaporate.
Once in the storage tank, quality control samples will be taken and analysed. The notified chemical will be
fed from the storage tank to the ethylene crackers through a pipeline. The produced ethylene will be used to
prepare low and high-density polyethylene, alpha-olefins and poly-alpha-olefins. The by-products from the
ethylene cracker (various C3, C4 and higher olefins, methane, hydrogen and low MW aromatics such as
benzene, toluene and ethylbenzene) are separated, purified and marketed. The ethylene crackers tubes are de-
coked (cleaned) approximately every 30 days by burning off the coke using steam and air in different
proportions and at different temperatures for 12-48 hours. The hydrocarbon waste produced during de-coking
(which contains ~100 kg of the notified chemical per reactor) is captured with all of the separated materials
then incinerated.
6. HUMAN HEALTH IMPLICATIONS
6.1 Exposure assessment
6.1.1 Occupational exposure
NUMBER AND CATEGORY OF WORKERS
Number/ Exposure Duration Exposure Frequency
Category of Worker
site (hours/day) (days/year)
Unloading 1-2 1-8 3
Sampling and analysis 1-2 0.2 3
Cleaning 1-2 Intermittent 12
EXPOSURE DETAILS
Transport
During transport of the notified chemical to the on-site storage tanks workers are not expected to be exposed
to the notified chemical except in the event of a spill or leak.
Industrial Use
While the use of the notified chemical as an ethylene feedstock is an automated and enclosed process, there is
still some potential for exposure of workers. Dermal, and accidental ocular exposure to drips, spills and
splashes may occur during the connection and disconnection of transfer hoses and during quality control
sampling. This exposure is expected to be minimised by the use of personal protective equipment (including
gloves, coveralls, eye protection and hard hat) and by the engineering controls (vacuum back flush and hose
caps). Inhalation exposure to notified chemical vapours may also occur during these processes, especially as
the notified chemical has a high vapour pressure (4.4 kPa at 25oC) and will readily evaporate if spilt.
6.1.2. Public exposure
It is expected that during transport, storage and industrial use exposure to the public will be negligible, except
in the event of an accidental spill.
6.2. Human health effects assessment
The results from toxicological investigations conducted on the notified chemical and analogues are summarised
in the table below. Analogue data has been provided for a number of petroleum derived naphtha streams that
together cover the carbon range of the notified chemical (More detailed information on the analogues can be
found in Appendix B). Analogue data is listed only for the endpoints in which there was no data on the
FULL PUBLIC REPORT: STD/1274 Page 5 of 23
09 September 2008 NICNAS
notified chemical. All tests followed GLP unless otherwise mentioned. Details of the studies conducted on the
notified chemical can be found in Appendix B. The full study reports for the analogues have not been reviewed
by NICNAS.
Endpoint Test Substance Result and Assessment Source
Conclusion
Rat, acute oral toxicity Notified chemical oral LD50 > 5000 mg/kg bw Safepharm
low toxicity Laboratories
(2006c)
Rat, acute dermal toxicity Analogue 1 LD50 > 2000 mg/kg bw API (2003)
low toxicity
Rabbit, acute dermal Analogue 3 LD50 > 3160 mg/kg bw IUCLID (2000)
toxicity low toxicity
Analogue 4 LD50 > 2000 mg/kg bw IUCLID (2000)
low toxicity
Rat, acute inhalation Analogue 1 LC50 > 5 mg/L/4 hour API (2003)
low toxicity
toxicity
Analogue 3 LC50 > 12 mg/L/6 hour IUCLID (2000)
low toxicity
Analogue 4 LC50 > 5.24 mg/L/4 hour IUCLID (2000)
low toxicity
Rabbit, skin irritation Analogue 1 moderately irritating API (2003)
Analogue 3 slightly irritating IUCLID (2000)
Analogue 4 moderately irritating IUCLID (2000)
Rabbit, eye irritation Analogue 1 non-irritating API (2003)
Analogue 3 slightly irritating IUCLID (2000)
Analogue 4 slightly irritating IUCLID (2000)
Guinea pig, skin Analogue 1 no evidence of sensitisation API (2003)
sensitisation ?adjuvant Analogue 4 no evidence of sensitisation IUCLID (2000)
test.
Rat, repeat dose inhalation Analogue 2 NOAEL < 2220 ppm API (2003)
toxicity ?90 days.
Rat, repeat dose inhalation Analogue 4 NOAEL > 9.88 mg/L IUCLID (2000)
toxicity, 21 days
Rabbit, repeat dose dermal Analogue 1 NOAEL > 2000 mg/kg bw/day API (2003)
toxicity ?28 days. Analogue 4 NOAEL = 1000 mg/kg bw/day IUCLID (2000)
LOAEL = 2000 mg/kg bw/day
Mutagenicity ?bacterial Notified chemical non mutagenic Safepharm
reverse mutation Laboratories
(2006d)
Genotoxicity ?in vitro Notified chemical non genotoxic Safepharm
micronucleus test Laboratories
(2006e)
Genotoxicity ?in vivo Analogue 1 non genotoxic API (2003)
cytogenetic assay
API (2003)
Developmental and Analogue 2 NOAEL Parental > 24700
mg/m3
reproductive effects
NOAEL F1 offspring > 24700
mg/m3
Toxicokinetics, metabolism and distribution.
The notified chemical is likely to be absorbed through the lung and the gastro-intestinal tract (Illing 2006).
However no effects were seen in the acute oral toxicity study therefore absorption via the gastro-intestinal tract
is not confirmed. The notified chemical is expected to be metabolised by - or -1 oxidation to the alcohol and
then to the fatty acid. These fatty acids are then likely to enter intermediary metabolism (including -oxidation)
and be excreted in bile urine and exhaled air (Illing 2006).
FULL PUBLIC REPORT: STD/1274 Page 6 of 23
09 September 2008 NICNAS
Acute toxicity.
The notified chemical is considered to be of low acute toxicity via the oral route based on tests on the notified
chemical conducted in rats.
In the acute dermal toxicity study using Analogue 1, apart from skin irritation no clinical signs of toxicity were
observed. Skin irritation ranged from slight to severe for erythema and oedema, slight to moderate for atonia
and coriaceousness (leathery texture) and slight to moderate for desquamation and fissuring. Subcutaneous
haemorrhage, blanching and eschar were also observed.
The acute dermal toxicity study using Analogue 3 was not performed to GLP guidelines. Three rabbits of each
sex were exposed to a single dose for 24 hours, no deaths were recorded and clinical signs were reported to be
minimal.
The acute dermal toxicity study using Analogue 4 was similar to OECD guideline 402. No deaths were
recorded, slight to severe dermal irritation was observed. No systemic effects were evident.
All 10 animals in the acute inhalation study using Analogue 1 survived the test but exhibited languid behaviour
and a hunched appearance during exposure.
The acute inhalation study using Analogue 3 was not performed to GLP standards. There were no deaths and no
significant bodyweight changes, clinical findings or necropsy findings.
In the acute inhalation study using Analogue 4 that was similar to OECD guideline 403, there were no deaths,
but languid behaviour and squinted eyes were observed during exposure. There was also minimal incidences of
rhinorrhea. Gross post mortem and histopathological findings were not significant.
The notified chemical contains a number of hydrocarbons that are classified as R67: Vapours may cause
drowsiness and dizziness.
Based on toxicity data for the notified chemical and read across data, the notified chemical is considered to be of
low acute toxicity via the oral and dermal routes. The notified chemical is also considered to be of low toxicity
via inhalation but may cause effects on the central nervous system.
Irritation and Sensitisation.
A skin irritation test using Analogue 1 with a 24 hour occlusive exposure and 6 subjects gave a primary
irritation index (PII) value of 3.9 and had effects (both erythema and oedema) that were still present at the end of
the 14 day study although the effects had decreased from the maximum seen at 96 hours.
The skin irritation study using analogue three was not performed to GLP guidelines. Three rabbits of each sex
were treated with 0.5 mL of the test substance for four hours using a semi-occluded patch. Mean draize scores
for erythema of between 1 and 2 and for oedema between 0 and 1, were recorded at 24, 48 and 72 hours.
The skin irritation study using Analogue 4 was conducted using six New Zealand white rabbits, which were
exposed to 0.5 mL of the test substance for 24 hours to both abraded and non-abraded skin areas using an
occluded dressing. The PII was 4.9 indicating the test substance was moderately irritating.
No pain response or corneal or iridal irritation was seen in an eye irritation test using Analogue 1 where 0.1 mL
of undiluted test material was applied to one eye in each of the 9 test subjects.
The eye irritation study using Analogue 3 was not performed to GLP guidelines. Six albino rabbits had 0.1 mL
of the test substance applied to one eye. Apart from slight irritancy detected at 1 and 4 hours no irritation was
observed.
The eye irritation study using Analogue 4 showed slight eye irritation one hour after application but scores were
zero at 24, 48 and 72 hours. Nine New Zealand white rabbits were treated with 0.1 mL of the test substance,
three had their eyes washed with water after being treated.
Analogue 1 was tested for skin sensitisation using the Buehler method. At challenge one of ten test subjects
showed slight erythema as did one control subject. The positive and negative controls gave satisfactory
responses, confirming the validity of the test system.
Analogue 4 was tested for skin sensitisation using a closed patch test closely following the Buehler method
outlined in OECD guideline 406. It was concluded that the test substance was not sensitising.
Based on read across data, the notified chemical is considered to be moderately irritating to skin, a slight eye
irritant and is not considered to cause sensitisation by skin contact.
FULL PUBLIC REPORT: STD/1274 Page 7 of 23
09 September 2008 NICNAS
Repeated Dose Toxicity (sub chronic).
In a 90 day repeat dose inhalation toxicity study on Analogue 2, groups of 12 male and 12 female rats
underwent whole body exposures to 668, 2220 and 6646 ppm for six hours per day, five days per week for 13
weeks, followed by a 28 day recovery period. No mortalities were recorded during the study. Both sexes in the
high dose group showed an increased incidence of red facial staining. Haematological and clinical chemical
measurements were unaffected except for a 5% decrease in haemoglobin and haematocrit and a 7% decrease in
erythrocytes, however these changes were considered toxicologically unimportant as they were within the
historical range for the control. Kidney weights were increased in males at all dose levels and liver weights
were also increased for the high doses male and female test groups. The NOEL for subchronic toxicity was
determined to be 2220 ppm and for neurotoxicity was determined to be 6646 ppm.
In a 21 day repeat dose inhalation toxicity study on Analogue 4, groups of 20 animals (male and female) were
exposed to 1.13, 3.48 and 9.88 mg/L for six hours a day, five days per week for 21 days. No treatment related
effects considered relevant in humans were observed.
A 28 day repeat dose dermal toxicity study was conducted using Analogue 1 at doses of 200, 1000 and 2000
mg/kg bw/day. No mortalities were recorded during the study. Weight gains of treated animals over the course
of the study were similar to controls except for females in the high dose group, where the weight gain was
significantly reduced, this was considered to be a treatment related effect. There were no remarkable findings in
haematological data. Minimal to moderate irritation was seen in the skin of all animals treated with the test
substance.
A 28 day repeat dose dermal toxicity study was also conducted using Analogue 4 at doses of 200, 1000 and
2000 mg/kg bw/day. All animals treated with the test substance showed slight to severe skin irritation and
animals in the high dose group showed a significant decrease in their bodyweight. No treatment related trends
were evident from the haematology, clinical chemistry parameters and organ weight data.
The notified chemical is stated to contain 5% n-hexane which is classified as R48/20: Harmful: danger of
serious damage to health by prolonged exposure through inhalation.
Mutagenicity.
The notified chemical was negative in an Ames test and an in vitro micronucleus test. The notified chemical is
not considered to be mutagenic or genotoxic.
In the in vivo cytogenetic assay on Analogue 1 (API 2003) no evidence of genotoxicity was observed. In the
cytogenetics assay 5 of 18 male and 4 of 18 female test subjects receiving 3000 mg/kg bw died within 3 days.
Weight losses of 10 and 9% were seen in male and female test subjects respectively, other signs of toxicity
included piloerection, crusty eyes and noses and excess lacrimation. The positive and negative controls gave
satisfactory responses, confirming the validity of the test system.
Toxicity for reproduction.
Analogue 2 was tested in an adaptation of the Reproduction/Developmental Toxicity Screening Test (OECD
421). No animals died during the study, body and organ weights were unaffected and there were no treatment
related histopathological findings. No reduction in the fertility of the test subjects was observed. No significant
increase in developmental effects was observed when compared to the controls.
Although the tests on Analogue 2 indicated that the notified chemical may not be a reproductive toxin, the
notified chemical is stated to contain 5% n-hexane which is classified as Toxic to Reproduction Category 3
R62 Possible risk of impaired fertility.
Classification
Based on the read across data for skin irritation test and the viscosity of the notified chemical, the notified
chemical is classified as hazardous under the Approved Criteria for Classifying Hazardous Substances
(NOHSC, 2004).
As the notified chemical has not been tested for its health effects as a whole for a number of endpoints, the
notified chemical is also classified as hazardous under the Approved Criteria for Classifying Hazardous
Substances (NOHSC, 2004) based on the presence of hexane (CAS No. 110-54-3) at 5% and other
hydrocarbons.
FULL PUBLIC REPORT: STD/1274 Page 8 of 23
09 September 2008 NICNAS
The analogue petroleum derived naphtha streams are classified as Carc Cat 2, R45 may cause cancer. However
this classification need not apply if it can be shown that the substance contains less than 0.1% w/w benzene. As
the notified chemical contains less than 0.1% w/w benzene, classification with the risk phrase R45 is not
required.
6.3. Human health risk characterisation
6.3.1. Occupational health and safety
Due to the presence of hexane in the notified chemical it is classified as R48/20 danger of serious damage to
health by prolonged exposure through inhalation. Inhalation exposure to the notified chemical during the
connection and disconnection of transfer hoses should be reduced by the engineering controls present. The
presence of hexane and information on its exposure standard are included in the MSDS provided.
Management of airborne concentrations below the recommended occupational standard should minimise the
risk of adverse health effects.
There is also a risk to the occupational health and safety of workers from dermal exposure to the notified
chemical as it is classified as a skin irritant. Dermal exposure to the notified chemical is most likely to occur
during the connection and disconnection of transfer hoses, however engineering controls and the use of PPE
should reduce this. In addition, the high vapour pressure of the notified chemical is likely to limit dermal
uptake of the chemical (especially for the shorter chain hydrocarbons) due to evaporation from the skin.
The notified chemical is classified under the Australian Dangerous Goods Code as a Class 3 Flammable
Liquid; packaging group II. The risk to workers is greatest during the connection and disconnection of
transfer hoses, however engineering controls should reduce this.
Overall, although the notified chemical is classified as hazardous the low exposure expected from the
proposed use ensures that the risk to the occupational health and safety of workers is not considered to be
unacceptable.
6.3.2. Public health
The notified chemical will be available only to industrial end users. The unlikely but potential public
exposure through accidents during importation, transportation or storage is assessed as very low and hence the
risk to the public health from the notified chemical is not considered to be unacceptable.
7. ENVIRONMENTAL IMPLICATIONS
7.1. Environmental Exposure & Fate Assessment
7.1.1 Environmental Exposure
RELEASE OF CHEMICAL AT SITE
The notified chemical will be synthesised overseas and will be imported into Australia. Therefore,
environmental release within Australia will not occur at this stage.
RELEASE OF CHEMICAL FROM USE
The notified chemical is a site-limited intermediate used for the production of polyethylene and alpha-olefins.
A vacuum back flush system removes the notified chemical from the unloading hoses, which is further
automatically capped on removal to prevent spillage. It is estimated by the notifier that only a few grams that
reside on the surface of the hoses will be allowed to evaporate. Practically all notified chemical will be
consumed in the synthesis process.
RELEASE OF CHEMICAL FROM DISPOSAL
Due to the nature of the notified chemical and the dedicated handling equipment used to transfer the
notified chemical from import containers to receiving vessels, only a very small quantity is expected to be
released in effluents or in fugitive emissions. Due to the volatile nature of the notified chemical and its
low water solubility, releases are expected to ultimately partition to air.
FULL PUBLIC REPORT: STD/1274 Page 9 of 23
09 September 2008 NICNAS
7.1.2 Environmental fate
No studies of the biodegradability of the notified chemical were available. Brief details of biodegradation studies
are available for two related substances (Girling, AE and Fisk, PR, 2006).
Biodegradation studies of Analogue 5 reported 89% and 98% degraded in 28 days. The study was conducted to
OECD Guideline 301F (CEFIC-HSPA 2002).
A biodegradation study of Analogue 6 reported 10% degraded in 28 days. This was a closed bottle study, not
appropriate to poorly soluble substances (Exxon Biomedical Sciences, Inc. 1988).
Measured data for representative individual components have also been sought (Girling, AE and Fisk, PR,
2006). Data for "various components" were found in the public domain, and are in agreement with the
degradabilities that have been assigned when predicting the biodegradability of the substance.
The results of modelling show that 67.5% of the mass of the substance would be considered readily
biodegradable, passing the 10-day window, 22.5% would be readily biodegradable not passing the 10-day
window and 10% would be inherently biodegradable.
Girling, AE and Fisk, PR (2006) indicate that a reasonable conclusion that can be drawn from both the test and
predicted data is that, overall, the notified chemical should be considered to be readily biodegradable. The test
data also support the view that the substance passes the 10-day window criterion for ready biodegradability. The
measured data found in the literature for Analogue 1 supports this conclusion.
The predicted log KOW values of the chemical components of the notified chemical range from 2.3 to 5.3 with
approximately 80% of the mass having values > 3.0. In the absence of a measured bioconcentration factor (BCF)
a log KOW value that is > 3.0 is taken as an indicator of bioaccumulation potential. The components would
therefore be expected to have the potential to bioaccumulate. However, Girling, AE and Fisk, PR (2006) state
that the bioaccumulation potential may not be realised because of the high degradability potential of the
component hydrocarbons.
7.1.3 Predicted Environmental Concentration (PEC)
As release to the aquatic compartment is not expected, it is not possible to calculate an aquatic Predicted
Environmental Concentration.
7.2. Environmental effects assessment
There are no measured aquatic toxicity data for the notified chemical. However there are data for related
commercial substances. These data are summarised in the table below. It should be noted that the original
study reports have not been reviewed and have been reproduced from the supplied paper (Girling, AE and
Fisk, PR, 2006).
Analogue Result (mg/L) Method Reference
3 96 h LC50 = 10-18 Oncorhynchus mykiss. Data summarises valid acute toxicity CONCAWE (2001)
data using Water Accommodated Fraction (WAF) method
and covers 8 studies.
4 96 h LL50 = 27 Menidia beryllina. Test solutions were prepared using a CONCAWE (2001)
Water Accommodated Fraction (WAF) methodology.
48 h EC50 = 4.5-32 Daphnia magna. Data summarises valid acute toxicity data
3 CONCAWE (2001)
for LBPN's using Water Accommodated Fraction (WAF)
method and covers 6 studies.
48 h EL50 = 2.0 Mysidopsis bahia. Test solutions were prepared using a CONCAWE (2001)
4
Water Accommodated Fraction (WAF) methodology.
48 h LC50 = 2.0 Mysidopsis bahia. Semi-static test. Adema (1987)
5
96 h LC50 = 2.6 Chaetogammarus marinus. Semi static test in closed Exxon Chemical
6
vessels. International Inc. (1988)
3 72 h EL50 = 3.1 ?30000 Selenastrum capricornutum. Data summarises valid acute CONCAWE (2001)
FULL PUBLIC REPORT: STD/1274 Page 10 of 23
09 September 2008 NICNAS
toxicity data using Water Accommodated Fraction (WAF)
method and covers 11 studies.
72 h EC50 = 6.5 (NOEC = 0.1) OECD 201. Selenastrum capricornutum. Closed vessels. Springborn Laboratories
5
Included chemical analysis and GLP. Inc. (1993)
The results obtained by measurement in acute tests with related substances, and by prediction using QSAR
methodology (Girling, AE and Fisk, PR, 2006) are consistent for fish and invertebrates. Both sets of data give
lowest LL50 or EL50 values that are in the range of 1-10 mg/L. The predicted acute EL50 value for algae of 0.55
mg/L falls just below the lowest measured values that are in the range of 1-10 mg/L.
7.2.1 Predicted No-Effect Concentration
Using the most sensitive endpoint identified (Algae EL50), the PNEC has been calculated using an assessment
factor of 100.
Predicted No-Effect Concentration (PNEC) for the Aquatic Compartment
Algae EL50 0.55 mg/L
Assessment Factor 100
PNEC: 5.5 g/L
7.3. Environmental risk assessment
While the notified chemical's aquatic hazard is classified as being Acute Category 1, there will be limited, if
any, aquatic release during use, and based on the proposed use pattern and expected negligible environmental
exposure, the notified chemical is not considered to pose a risk to the environment.
8. CONCLUSIONS AND REGULATORY OBLIGATIONS
Hazard classification
Based on the available data the notified chemical is classified as hazardous under the Approved Criteria for
Classifying Hazardous Substances [NOHSC:1008(2004)]. The classification and labelling details are:
- Xi: R38 Irritating to skin.
- Xn: R48/20 Danger of serious damage to health by prolonged exposure through inhalation.
- Xn: R62 (category 3) Possible risk of impaired fertility.
- Xn: R65 May cause lung damage if swallowed.
- Xn: R67 Vapours may cause drowsiness and dizziness.
- S3 Keep in a cool place
- S9 Keep container in a well-ventilated place
- S16 Keep away from sources of ignition ?No smoking
- S24 Avoid contact with skin
- S36/37 Wear protective clothing and suitable gloves
- S51 Use only in well-ventilated areas
- S62 If swallowed, do not induce vomiting: seek medical advice immediately and show this
container or label
and
As a comparison only, the classification of the notified chemical using the Globally Harmonised System for the
Classification and Labelling of Chemicals (GHS) (United Nations 2003) is presented below. This system is not
mandated in Australia and carries no legal status but is presented for information purposes.
Hazard category Hazard statement
Skin irritation Category 3 Causes mild skin irritation
May be fatal if swallowed and enters
Aspiration Hazards Category 1
airways
FULL PUBLIC REPORT: STD/1274 Page 11 of 23
09 September 2008 NICNAS
Specific Target Organ
Category 3 May cause drowsiness and dizziness
Toxicity ?Single Exposure
Flammable liquids Category 2 Highly flammable liquid and vapour
Environment Acute Category 1 Very toxic to aquatic life
The above classification of the notified chemical using the GHS does not take into account the presence of
hexane.
Human health risk assessment
Under the conditions of the occupational settings described, the notified chemical is not considered to pose an
unacceptable risk to the health of workers.
When used in the proposed manner, the notified chemical is not considered to pose an unacceptable risk to
public health.
Environmental risk assessment
On the basis of the reported use pattern, the notified chemical is not considered to pose a risk to the
environment.
Recommendations
REGULATORY CONTROLS
Hazard Classification and Labelling
? The Office of the ASCC, Department of Employment and Workplace Relations (DEWR), should
consider the following health and physico-chemical hazard classification and safety phrases for the
notified chemical:
- Xi: R38 Irritating to skin.
- Xn: R48/20 Danger of serious damage to health by prolonged exposure through inhalation.
- Xn: R62 Possible risk of impaired fertility.
- Xn: R65 May cause lung damage if swallowed.
- Xn: R67 Vapours may cause drowsiness and dizziness.
- S3 Keep in a cool place
- S9 Keep container in a well-ventilated place
- S16 Keep away from sources of ignition ?No smoking
- S24 Avoid contact with skin
- S36/37 Wear protective clothing and suitable gloves
- S51 Use only in well-ventilated areas
- S62 If swallowed, do not induce vomiting: seek medical advice immediately and show this
container or label
? Use the following risk phrases for products/mixtures containing the notified chemical:
- Conc 20%: R38; R67; R65
- 15% Conc < 20%: R67; R65
- 10% Conc < 15%: R65
The risk phrases R62 and R48/20 should be assigned based on the hexane content of the
product/mixture.
? The notified chemical should be classified as follows under the ADG Code:
- Class 3 Flammable Liquid; packaging group II
Health Surveillance
FULL PUBLIC REPORT: STD/1274 Page 12 of 23
09 September 2008 NICNAS
? As the notified chemical is a health hazard (including danger of serious damage to health by prolonged
exposure through inhalation and possible risk of impaired fertility), employers should determine
whether health surveillance is required for any worker where the workplace risk assessment identifies a
significant risk to health.
CONTROL MEASURES
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise occupational exposure to
the notified chemical:
- Vacuum back flush system to remove the notified chemical from the unloading hoses
- Local and/or general ventilation to control airborne levels
? Employers should implement the following safe work practices to minimise occupational exposure
during handling of the notified chemical:
- Use only in well ventilated areas
- Avoid skin contact
- Workers must have adequate education and training before handling the notified chemical.
? Employers should ensure that the following personal protective equipment is used by workers to
minimise occupational exposure to the notified chemical:
- Safety glasses
- Gloves
- Coveralls
- Respiratory protection, if significant inhalation is expected
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous to health in
accordance with the Approved Criteria for Classifying Hazardous Substances [NOHSC:1008(2004)]
workplace practices and control procedures consistent with provisions of State and Territory hazardous
substances legislation must be in operation.
Disposal
? The notified chemical should be disposed of by incineration.
Storage
? The following precautions should be taken regarding storage of the notified chemical:
- Store in a cool, well ventilated area away from sources of ignition
Emergency procedures
? Spills or accidental release of the notified chemical should be handled by physical containment,
collection and subsequent safe disposal.
Transport and Packaging
? The notified chemical is a Dangerous Good (Class 3, Flammable Liquid) under the ADG code. All
relevant requirements for transport, packaging, labelling and storage should be complied with.
FULL PUBLIC REPORT: STD/1274 Page 13 of 23
09 September 2008 NICNAS
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The Director may call for
the reassessment of the chemical under secondary notification provisions based on changes in certain
circumstances. Under Section 64 of the Industrial Chemicals (Notification and Assessment) Act (1989) the
notifier, as well as any other importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations apply even when the
notified chemical is listed on the Australian Inventory of Chemical Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier, other importer or
manufacturer:
(1) Under Section 64(2) of the Act; if
- the function or use of the chemical has changed from a feedstock in ethylene crackers, or is likely
to change significantly;
- the amount of chemical being introduced has increased from 100,000 tonnes, or is likely to
increase, significantly;
- if the chemical has begun to be manufactured in Australia;
- additional information has become available to the person as to an adverse effect of the chemical
on occupational health and safety, public health, or the environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and assessment) is required.
No additional secondary notification conditions are stipulated.
Material Safety Data Sheet
The MSDS of the notified chemical provided by the notifier was reviewed by NICNAS. The accuracy of the
information on the MSDS remains the responsibility of the applicant.
FULL PUBLIC REPORT: STD/1274 Page 14 of 23
09 September 2008 NICNAS
APPENDIX A: PHYSICAL AND CHEMICAL PROPERTIES
< -20oC
Freezing Point
Method EC Directive 92/69/EEC A.1 Melting/Freezing Temperature.
Remarks No significant protocol deviations. GLP compliant.
No change in the appearance of the test material was observed.
Test Facility Safepharm Laboratories (2006a)
62-181oC at 100.8 kPa
Boiling Point
Method ASTM D 86, Standard Test Method for Distillation of Petroleum Products at Atmospheric
Pressure.
Remarks The initial determination of the boiling point range was determined in the SafePharm
Laboratories using the distillation method according to the EC Directive 92/69/EEC A.2
Boiling Temperature. In this initial test approximately 96% of the test material boiled in
the range of 59 to 154oC. However, it was considered by the test laboratory that this was
not appropriate for test materials of this nature.
Therefore, the boiling point range was determined at Shell Research Ltd (non-GLP) using
the ASTM D 86 method. This method uses specific apparatus that controls heating rate,
temperature of the condenser and temperature of the collection vessel. These parameters
are very specific for a particular petroleum product type and can have a significant effect
on the boiling temperature obtained.
Test Facility Safepharm Laboratories (2006a)
701 kg/m3 at 20oC
Density
Method EC Directive 92/69/EEC A.3 Relative Density.
Remarks No significant protocol deviations. GLP compliant.
The density was determined using the pycnometer method.
Test Facility Safepharm Laboratories (2006a)
4.4 kPa at 25oC
Vapour Pressure
Method EC Directive 92/69/EEC A.4 Vapour Pressure.
Remarks No significant protocol deviations. GLP compliant.
The vapour pressure was determined using an isoteniscope system at 48.2 ?79.5癈 and
linear regression.
The test was conducted without prior degassing in order to minimise the loss of volatile
components.
Test Facility Safepharm Laboratories (2006b)
<1 mg TOC/L for C4-10 at 20 ?.5癈
Water Solubility
Method EC Directive 92/69/EEC A.6 Water Solubility.
Remarks Due to the test material being a very complex mixture of hydrocarbons, and it also being
essentially insoluble in water, analysis of the sample solutions was performed monitoring
the TOC content of the sample solutions only. The preliminary water solubility test
indicated that the solubility was less than 1x10-2 g/L. However, due to the physical nature
of the test material, it was not possible to use the column method; experience has shown
that liquid test materials coated onto glass beads cause these beads to adhere together
forming a plug within the column and thus preventing water circulation.
Mixtures of test material and water were added to three separate flasks to obtain a
nominal loading concentration of 0.10 g/L of solution. After shaking at approximately
30癈 and subsequently standing for 20癈 for 24 h, the contents of the flasks were
centrifuged. Each supernatant was then sampled excluding excess, undissolved test
material and was analysed using a Shimadzu TOC-5050A instrument to determine the
FULL PUBLIC REPORT: STD/1274 Page 15 of 23
09 September 2008 NICNAS
total organic carbon (TOC) content in solution. No significant protocol deviations. GLP
compliant.
Test Facility Safepharm Laboratories (2006b)
log POW = 4.40 to >6.50 at 20癈
Partition Coefficient (n-
octanol/water)
Method EC Directive 92/69/EEC A.8 Partition Coefficient.
Remarks HPLC Method. 0.5124 g was diluted to 10 mL with methanol. Peaks from the notified
chemical eluted after the reference substances Naphthalene, Phenanthrene,
Triphenylamine and DDT. By percentage are normalisation, 60.2% of the test material
had a POW value greater than 6.50.
Test Facility Safepharm Laboratories (2006b)
log Koc = 2.05 to >5.63
Adsorption/Desorption
?screening test
Method EC Directive 67/548/EEC C19.
Remarks HPLC Method. Peaks from the notified chemical eluted after the reference substances
Atrazine, Linuron, Naphthalene, Endosulfan-diol, Fenthion, -Endosulfan, Phenanthrene,
Diclofop-methyl, DDT.
The test material was known to primarily be a complex mixture of alkanes and therefore a
majority of the components were not anticipated to absorb in the UV region. Preliminary
assessment of the test material therefore used a refractive index (RI) detector.
Unfortunately, unlike the partition coefficient, fraction collection and GC analysis
indicated that negligible components were successfully eluted when maintaining an
isocractic mobile phase, in this case at a ratio of 55:45 v/v methanol:water as required by
the method guideline. A gradient increase in the methanol content of the mobile phase
composition was therefore required at a time greater than the retention time of the highest
calibration standard to elute a majority of the test material. This requirement for a
gradient method invalidated the use of the RI detector. This is since the detector baseline
is adversely affected by the continuing shift in the refractive index of the mobile phase
caused by the gradient. Therefore the sample was monitored in the far UV region,
possibly detecting trace levels of aromatics, and the elution of the test material confirmed
by fraction collection and subsequent GC analysis.
With the exception of the component at a GC retention time of approximately 5.1
minutes, all the major components of the test material were positively detected in the
analysed fractions. The absence of this single component was noted but concluded not to
impact on the validity of the test. This was since a significant majority of the test
material, greater than 90%, had been successfully detected and quantified.
The retention time limit value used for the calculation of the adsorption coefficient for
those components identified in the collected fractions represent the start of the amended
100% methanol mobile phase. All these components share a common adsorption
coefficient value, that of greater than the highest calibration standard. The method
guideline states that the measurement of adsorption coefficient be performed on the
ionised and unionised form of the test material. However, in the absence of any
dissociating groups, the test material being a mixture of alkanes, the determination was
performed at an approximately neutral pH only, on the test material in an unionised form.
The adsorption coefficient of the test material has been determined to be log Koc = 2.05 to
>5.63. By fraction collection and subsequent GC analysis, 91.4% of the test material had
a log Koc >5.63, calculated from GC normalisation data.
Test Facility Safepharm Laboratories (2006b)
-18oC at 101.325 kPa
Flash Point
FULL PUBLIC REPORT: STD/1274 Page 16 of 23
09 September 2008 NICNAS
Method EC Directive 92/69/EEC A.9 Flash Point.
Remarks No significant protocol deviations. GLP compliant.
The closed cup method was used.
Test Facility Safepharm Laboratories (2006b)
256oC
Autoignition Temperature
Method EC Directive 92/69/EEC A.15 Auto-Ignition Temperature (Liquids and Gases).
Remarks No significant protocol deviations. GLP compliant.
Test Facility Safepharm Laboratories (2006b)
FULL PUBLIC REPORT: STD/1274 Page 17 of 23
09 September 2008 NICNAS
APPENDIX B: TOXICOLOGICAL INVESTIGATIONS
B.1. Acute toxicity ?oral
TEST SUBSTANCE Notified chemical
OECD TG 420 Acute Oral Toxicity - Fixed Dose Method.
METHOD
EC Directive 2004/73/EC B.1bis Acute Toxicity (Oral) Fixed Dose
Method.
Species/Strain Rat/Sprague-Dawley CD (Crl : CD?(SD) IGS BR)
Vehicle Test substance was used as supplied. GLP compliant.
Remarks - Method No significant protocol deviations. A preliminary test was done on one
female rat in which there were no deaths at a dose rate of 5000 mg/kg
bodyweight, an additional four fasted female rats were then treated at this
dose rate.
RESULTS
Group Number and Sex Dose Mortality
of Animals mg/kg bw
1 1 female 5000 0
2 4 females 5000 0
LD50 > 5000 mg/kg bw
Signs of Toxicity There were no deaths or test substance-related clinical signs or
remarkable body weight changes during the study period.
Effects in Organs There were no remarkable necropsy findings.
The notified chemical is of low toxicity via the oral route.
CONCLUSION
TEST FACILITY Safepharm Laboratories (2006c)
B.2. Genotoxicity ?bacteria
TEST SUBSTANCE Notified chemical
OECD TG 471 Bacterial Reverse Mutation Test.
METHOD
EC Directive 2000/32/EC B.13/14 Mutagenicity ?Reverse Mutation Test
using Bacteria.
Plate incorporation procedure
Species/Strain S. typhimurium: TA1535, TA1537, TA98, TA100
E. coli: WP2uvrA-
Metabolic Activation System S9 fraction derived from Phenobarbital/-napthoflavone induced rat liver
Concentration Range in a) With metabolic activation: 0.5 - 5000 礸/plate
Main Test b) Without metabolic activation: 1.5 - 5000 礸/plate
Vehicle Acetone; test substance applied as solution
Remarks - Method No significant protocol deviations. GLP compliant.
RESULTS
Metabolic Test Substance Concentration (礸/plate) Resulting in:
Activation Cytotoxicity in Cytotoxicity in Precipitation Genotoxic Effect
Preliminary Test Main Test
Absent
Test 1 500 500 5000 Negative
Test 2 500 5000 Negative
Present
FULL PUBLIC REPORT: STD/1274 Page 18 of 23
09 September 2008 NICNAS
Test 1 1500 500 5000 Negative
Test 2 500 5000 Negative
Remarks - Results No significant increases in the frequency of revertant colonies were
recorded for any of the bacterial strains at any dose level, either with or
without metabolic activation.
A visible reduction in the background lawn was seen in the Salmonella
tester strains, with and without metabolic activation and predominantly in
the base-pair substitution strains.
The positive and negative controls gave satisfactory responses,
confirming the validity of the test system.
The notified chemical was not mutagenic to bacteria under the conditions
CONCLUSION
of the test.
TEST FACILITY Safepharm Laboratories (2006d)
B.3. Genotoxicity ?in vitro
TEST SUBSTANCE Notified chemical
Draft OECD TG 487 In vitro Micronucleus Test.
METHOD
Species/Strain Human
Cell Type/Cell Line Peripheral lymphocytes
Metabolic Activation System S9 fraction derived from Phenobarbital/-napthoflavone induced rat liver
Vehicle Not specified
Remarks - Method The draft guideline OECD TG 487 In vitro Micronucleus Test was
modified to more closely resemble the guideline OECD TG 473 In vitro
Mammalian Chromosome Aberration Test. The modification made was
the adoption of the exposure groups from the OECD 473 guideline in
preference to those suggested in the draft OECD 487 guideline.
The maximum treatment concentration (1250 g/mL) was chosen based
on a preliminary toxicity study in which above this concentration the
notified chemical formed an oily layer on top of the culture medium.
GLP compliant.
Metabolic Test Substance Concentration (g/mL) Exposure Expression Selection
Activation Period Time Time
Absent
Test 1 0*, 39, 78.1, 156.25, 312.5*, 625*, 1250* 4 hours 16 hours 28 hours
Test 2 0*, 4.88, 9.75*, 19.5*, 39*, 78.1, 117.2 20 hours 0 hours 28 hours
Present
Test 1 0*, 39, 78.1, 156.25, 312.5*, 625*, 1250* 4 hours 16 hours 28 hours
Test 2 0*, 39, 78.1, 156.25, 312.5*, 625*, 1250* 4 hours 16 hours 28 hours
*Cultures selected for metaphase analysis.
RESULTS
Metabolic Test Substance Concentration (礸/mL) Resulting in:
Activation Cytotoxicity in Cytotoxicity in Precipitation Genotoxic Effect
Preliminary Test Main Test
Absent
Test 1 >1250 >1250 >1250 Negative
Test 2 156.25 78.1 >117.2 Negative
Present
Test 1 >1250 >1250 >1250 Negative
Test 2 >1250 >1250 >1250 Negative
FULL PUBLIC REPORT: STD/1274 Page 19 of 23
09 September 2008 NICNAS
Remarks - Results In both experiments in the absence and presence of metabolic activation,
no biologically relevant increase in the number of cells carrying structural
chromosome aberrations was observed.
The positive and negative controls gave satisfactory responses,
confirming the validity of the test system.
The notified chemical was not clastogenic to human lymphocytes treated
CONCLUSION
in vitro under the conditions of the test.
TEST FACILITY Safepharm Laboratories (2006e)
B.4. Analogues
The identities of the petroleum derived analogues considered for each of the endpoints where no information
was available on the notified chemical are listed in the table below:
Ana- Substance Class CAS No Description Reference
logue
1 Light alkylate Naphthas API (2003)
64741- Paraffinic naphtha streams are obtained by alkylation
naphtha in the 66-8 (catalytic reaction), isomerization (catalytic
range conversion) and solvent extraction. They contain
C5-C10 mostly saturated hydrocarbons, generally in the range
C5 to C10 and boil in the range of 90 to 160癈.
2 Light alkylate Naphthas Not A distillate fraction of light alkylate naphtha. API (2003)
naphtha distillate in the specified The composition is as follows;
(LAN-D) range Carbon number Volume %
C4-C10 4 3.25
5 33.3
6 18.61
7 9.81
8 31.14
9 3.21
10 0.39
The composition of the test substance used in the
reproduction/developmental toxicity screening
contained only C4 and C5 hydrocarbons
IUCLID (2000)
64742- A complex combination of hydrocarbons obtained
Naphthas
3 Heavy
82-1 from a catalytic hydrodesulfurization process. It
in the
hydrodesulphurized
consists of hydrocarbons having carbon numbers
range
naphtha
predominantly in the range of C7 through C12 and
C7-C12
boiling in the range of approximately 90癈 to 230癈
(194癋 to 446癋).
4 Naphtha Naphthas 64741- A complex combination of hydrocarbons from IUCLID (2000)`
(petroleum), heavy in the 83-9 distillation of the products from a thermal cracking
thermal cracked range process. It consists predominantly of unsaturated
C6-C12 hydrocarbons having carbon numbers predominantly
in the range of C6 through C12 and boiling in the
range of approximately 65癈 to 220癈 (148癋 to
428癋).
5 Naphtha Naphthas 64742- A complex combination of hydrocarbons obtained by
(petroleum), in the 49-0 treating a petroleum fraction with hydrogen in the
hydrotreated light range presence of a catalyst. It consists of hydrocarbons
C4-C11 having carbon numbers predominantly in the range of
C4 through C11 and boiling in the range of
approximately minus 20癈 to 190癈 (-4癋 to 374癋).
6 Naphtha Naphthas 64742- A complex combination of hydrocarbons obtained by
(petroleum), in the 48-9 treating a petroleum fraction with hydrogen in the
hydrotreated heavy range presence of a catalyst. It consists of hydrocarbons
C6-C13 having carbon numbers predominantly in the range of
C6 through C13 and boiling in the range of
approximately 65癈 to 230癈 (149癋 to 446癋).
7 Low boiling point Naphthas 64742- A complex combination of hydrocarbons obtained by CONCAWE
Naphtha in the 49-0 and treating a petroleum fraction with hydrogen in the (2001)
range 64742- presence of a catalyst. It consists of hydrocarbons
C4-C11 89-8 having carbon numbers predominantly in the range of
C4 through C11.
FULL PUBLIC REPORT: STD/1274 Page 20 of 23
09 September 2008 NICNAS
8 Solvent Naphtha, Naphthas CONCAWE
64742- A complex combination of hydrocarbons obtained
petroleum, light in the (2001)
89-8 from the distillation of crude oil or natural gasoline. It
aliphatic range consists predominantly of saturated hydrocarbons
C5-C10 having carbon numbers predominantly in the range of
C5 through C10.
Naphtha (petroleum) solvent refined light (Substance Adema (1987)
9 Alkylated Naphtha Not
contains benzene) and Springborn
assigned
Laboratories Inc.
but in
(1993)
IUCLID
for
64741-
81-0
10 Naphtha 64742- Naphtha (petroleum) solvent refined light (Substance
Exxon Chemical
48-9 contains benzene) International Inc.
(1988)
Various Components Hexane (confidential IUCLID), 2-methylpentane (confidential IUCLID), 2-methylbutane (Solano-
Serena, 2000) and n-decane (Verschueren, 1983; Wakeham, 1986)
FULL PUBLIC REPORT: STD/1274 Page 21 of 23
09 September 2008 NICNAS
BIBLIOGRAPHY
Adema, D.D.M. (1987). Aquatic toxicity of compounds that may be carried by ships (Marpol 1973, Annex 11).
A progress report for 1986, Report No. R86/326a, TNO, Delfi, Netherlands.
API (2003) Robust summary of information on paraffinic naphthas. American Petroleum Institute.
CEFIC-HSPA (2002), The classification of petroleum solvent streams and related complex hydrocarbon
solvents for aquatic environmental effects under the EU dangerous substances directive, prepared by the
Hydrocarbon Solvents Producers Association.
CONCAWE. (1993). Ecotoxicological testing of petroleum products: test methodology. Report no. 92/56.
CONCAWE. (2001). Environmental classification of petroleum substances - summary data and rationale.
Report No. 01/54. CONCAWE Petroleum Products Ecology Group, CONCAWE, Brussels.
DiToro, D.M., McGrath, J.A. and Hansen, D. (2000). Technical basis for narcotic chemicals and polycyclic
aromatic hydrocarbon criteria. I. Water and tissue. Environmental Toxicology and Chemistry, 19(8), 195 1-
1970.
Exxon Biomedical Sciences, Inc. (1988) Biodegradability: Closed Bottle Test (EXXSOL D40). EBSI Report #
88MRL 175.
Exxon Chemical International Inc. (1988). A practical guide to protecting man and the environment, Exxon,
Belgium.
FORS (Federal Office of Road Safety) (1998) Australian Code for the Transport of Dangerous Goods by Road
and Rail (ADG code), 6th Edition, Canberra, Australian Government Publishing Service
Girling, AE and Fisk, PR, 2006, [Notified Chemical]: Environmental Hazard Property Summary Review, Draft
April 2006, Unpublished Paper, Peter Fisk Associates, 39 Bennell's Avenue, Whitstable, Kent, CT52HP,
UK
Illing (2006) Summary of Toxicological Information Relevant to Annex VII A Notification End Points
(Unpublished report submitted by the notifier).
IUCLID (International Uniform Chemical Information Database) (2000) Hydrocarbons, C6-11, hydrotreated,
dearomatized (CAS No. 93763-33-8): Dataset. European Commission-European Chemicals Bureau, 32 pp,
19 February 2000.
McGrath J.A., Parkerton T.F., Helleweger F.L., Di Toro D.M. (2005). "Validation of the narcosis target lipid
model for petroleum products: gasoline as a case study". Environmental Toxicology and Chemistry, 24(9),
2382-2394.
NOHSC (1994) National Code of Practice for the Labelling of Workplace Substances [NOHSC:2012(1994)].
National Occupational Health and Safety Commission, Canberra, Australian Government Publishing
Service.
NOHSC (2003) National Code of Practice for the Preparation of Material Safety Data Sheets, 2nd edition
[NOHSC:2011(2003)]. National Occupational Health and Safety Commission, Canberra, Australian
Government Publishing Service.
NOHSC (2004) Approved Criteria for Classifying Hazardous Substances, 3rd edition [NOHSC:1008(2004)].
National Occupational Health and Safety Commission, Canberra, AusInfo.
OECD (2000). Guidance document on aquatic toxicity testing of difficult substances and mixtures. OECD
Environmental Health and Safety Publications, Series on Testing and Assessment, No. 23. OECD, Paris
Safepharm Laboratories (2006a) Determination of hazardous physico-chemical properties (SPL Project Number
2041/002 February 2006), Safepharm Laboratories Ltd, Derbyshire, UK (Unpublished report submitted by
the notifier).
Safepharm Laboratories (2006b) Determination of general physico-chemical properties (SPL Project Number
2041/001 February 2006), Safepharm Laboratories Ltd, Derbyshire, UK (Unpublished report submitted by
the notifier).
Safepharm Laboratories (2006c) Acute oral toxicity in the rat ?fixed dose method (SPL Project Number
2041/0047 November 2006), Safepharm Laboratories Ltd, Derbyshire, UK (Unpublished report submitted
by the notifier).
FULL PUBLIC REPORT: STD/1274 Page 22 of 23
09 September 2008 NICNAS
Safepharm Laboratories (2006d) Salmonella typhimurium and Escherichia coli/mammalian-microsome reverse
mutation assay (SPL Project Number 2041/0016 April 2006), Safepharm Laboratories Ltd, Derbyshire, UK
(Unpublished report submitted by the notifier).
Safepharm Laboratories (2006e) Micronucleus test in human lymphocytes in vitro: draft OECD method 487
(SPL Project Number 2041/0034 November 2006), Safepharm Laboratories Ltd, Derbyshire, UK
(Unpublished report submitted by the notifier).
Solano-Serena, F., Marchal, L., Huet,T., Lebeault, J.-M., Vandecasteele, J.P. (2000) Biodegradability of volatile
hydrocarbons of gasoline. Appl. Microbiol. Biotechnol, 54, 121.
United Nations (2003) Globally Harmonised System of Classification and Labelling of Chemicals (GHS).
United Nations Economic Commission for Europe (UN/ECE), New York and Geneva.
FULL PUBLIC REPORT: STD/1274 Page 23 of 23
|