PRODUCT DATA SHEET
511 Look Penetrating Sealer
Impregnator
Natural www.miraclesealants.com
Water, Stain & Slip Protection for ing the tile or stone surface a second time. Be careful not to allow the sealer to pud-
dle or dry on presealed surfaces.
s Quarry Tile s Ceramic Tile s Porcelain Tile
Existing Installation - Surface Preparation
s Glazed Tile s Marble s Granite
s Travertine s Medium -Dense Slate s Grout
Surface must be dry and free of contaminants, including previously applied sealers,
s Quartz s Medium -Dense Brick s Terrazzo
dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
Uses
Surface Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira
s Interior & Exterior s Kitchen s Showers
Strip or H2O Strip as directed.
s Restrooms s Patios s Drive Ways
Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust,
Special Features
grease and other heavy dirt and grime use GCFR (Grout & Concrete Film Remover)
s Easy-to-Use s Weather Resistant s Low Toxicity
Phosphoric Acid Cleaner as directed.
s Salt Resistant s Non Coating s Freeze/Thaw Resistant
For a non acid deep clean use Liquid Poultice as directed.
s Acid Resistant s Non Yellowing s Stain Resistant
s Slip Resistant s U.V. Transparent s Water Resistant Light Cleaning: Use Mira Clean #1, Porcelain & Ceramic Tile Cleaner, Tile & Grout
Cleaner, Mira Soap, Counter Kleen as directed.
PRODUCT DE SCRIPTION Existing Installation - Application Instructions
KEEP OUT OF REACH OF CHILDREN. This product is formulated for sealing concrete Follow the application instructions previously mentioned, except now, seal the grout
and masonry to provide resistance against water, alkalis, acids, ultraviolet light, stain- and tile or stone surfaces at the same time. When treating surfaces together, make
ing, salt ion intrusion and freeze/thaw damage. 511 Impregnator is a unique poly- sure that the recessed grout is saturated.
merized silicone formulation designed for the protection of all medium to dense
Mold, Mildew and Bacteria Sanitation
porous tile, stone and grout surfaces. 511 Impregnator penetrates into the surface
For best results in killing mold, mildew, bacteria and other micro organisms, use
and forms an invisible barrier that is resistant to moisture and stains, while allowing
Miracle Disinfectant as directed.
vapor to escape. 511 Impregnator is not a surface coating and will not alter the natur-
al look. All surfaces are harder and less slippery. 511 Impregnator can be used on Residue Removal
interior and exterior applications. 511 Impregnator is U.V. transparent, resists acid
To remove accumulated 511 Impregnator residue, use Miracle Residue Remover as
rain and will not yellow under any circumstances. 511 Impregnator averages five to
directed.
twenty times the coverage of competitive products. (See coverage chart). 511 has
been formulated for or applied to freshly poured concrete to retard the evaporation Color and Gloss Enhancement
of water. For color & gloss enhancement, use Mira Matte or Mira Shine as directed.
511 Impregnator is on the approved sources list of the United States Postal Service
Cure Time
and is U.S.D.A. approved for incidental food contact in federal meat and poultry
511 Impregnator will be dry to the touch in 1 - 3 hours and may be used for normal
establishments.
foot traffic. For optimum results the area should be kept dry and free from staining
Test Data
materials for 72 hours.
Independent laboratory tests show 511 Impregnator out performs competitive prod-
Coverage Chart - Used as directed
ucts. Test results are available upon request for Staining, Static Coefficient of Friction,
Cost per 1000 sq.ft. 2000 sq.ft. 3000 sq.ft. 4000 sq.ft.
Tabor Abrasion, Surface Absorption, Freeze/Thaw, Vapor Transmission and Bacteria
sq.ft/sq.m. 90 sq.m. 180 sq.m. 270 sq.m. 360 sq.m.
Repellency.
Sanded Grout (.06-.11)
NOTE: On more porous surfaces use 511 Porous Plus as directed. For any questions
concerning grout refer to the grout manufacturers specifications. 511 Impregnator Quarry Tile (.05-.09)
will not stop acid etching. Ceramic Tile (.03-.05)
Glazed Tile (.03-.05)
Sample Testing
Porcelain Tile (.02-.03)
Due to the differences of each substrate, several inconspicuous test patches should
Polished Granite (.02-.03)
be completed to assure maximum performance. User must determine suitability of
Polished Marble (.02-.03)
the product for their intended use.
Terrazzo (.03-.05)
Color Enhancement Brick (.05-.09)
For added color with 鈥淭EXTURED AND NON POLISHED鈥? surfaces, 511 Seal & Slate (.05-.09)
Enhance or Mira Matte may be applied as directed. Quartz (.03-.05)
Gloss Enhancement Travertine (.03-.05)
Masonry (.05-.09)
For a higher gloss finish on POLISHED stone surfaces, use Water Ring & Etch
Remover, Marble Conditioner, Mira Dust or MiraPolish. For counters and furniture, Cost per sq.ft. is based on a suggested list price of $105/gallon. 1 gallon = 3.785 litters.
use Stone Polish. For tile surfaces, try Tile Brite.
Slip Resistance MAINTENANCE
511 Impregnator increases the static coefficient of friction on all surfaces. 511 For ongoing maintenance instructions please refer to Miracle Sealants Care Guide.
Impregnator has been used successfully for compliance with the American Disability Refer to the Miracle Sealants Product Recommendation Chart for specific product
Act鈥檚 recommendations for slip resistance (ASTM C 1028-89) on polished & honed recommendations.
surfaces. Storage
Protect Neighboring Surfaces Store 511 Impregnator in the original container, properly sealed to avoid contamina-
tion and solvent evaporation. Stored at 770 F (400 C), 511 Impregnator will have a
Always protect neighboring surfaces including wood, carpet, metal, landscaping and
other non masonry surfaces. shelf life of 12 months.
Technical Support
NEW INSTALL ATIONS - APPLIC ATION INSTRUCTIONS For additional technical support, contact Miracle Sealants Company at
Read entire label and PDS/MSDS before using. 511 Impregnator should not be 1-800-350-1901 or 626-443-6433 ext. 3013
diluted or thinned in any way. 511 Impregnator should be used as is direct from
Office Hours
approved container.
Monday - Friday from 8:30 am - 5:00 pm PT.
Before Grouting: Apply 511 Impregnator to all surfaces prior to grouting. This step
1-626-443-6433 1-800-350-1901 鈥? Fax: 1-626-443-1435
will allow quick and easy cleanup after grouting. Grout can stain many surfaces if this
website: www.miraclesealants.com
procedure is not used prior to the grouting process. Apply 511 Impregnator using a
Product Damaged During Transportation
Mira Brush or a clean towel. Apply enough to wet the surface. (See coverage charts)
Be careful not to saturate the open grout joints. Allow 511 Impregnator to stand for If product is damaged during transportation contact
approximately 3 - 5 minutes for maximum penetration. All excess must be removed Info Trac @ 1-800-535-5053
at this time by buffing surface with a clean dry towel. This is very important on pol-
Additional Product
ished, glazed and porcelain surfaces. Allow 511 Impregnator to cure for 12 - 24 hours
Miracle Sealants Company offers a complete line of water & stain repellents,
before continuing with the grouting procedure.
sealers, cleaners, polishing compounds, diamond abrasives, machinery and
After Grouting: Once grouted, make sure that all grout residue is removed from the
accessories for the tile, stone, concrete, metal, fabric and carpet professional or
surface with a clean sponge and water. Allow grout to cure per manufacturers specifi-
do-it-yourself specialist.
cation. If grout clean up is not performed effectively, an additional cleaning may be
necessary to remove remaining grout residue or haze. For this procedure use
Phosphoric Acid Cleaner , (GCFR) Grout & Concrete Film Remover (Hydrochloric
Acid), Sulfamic Acid Crystals or Epoxy Grout Film Remover following the instructions
carefully. Once the area has completely dried, proceed with the sealing of the grout
for water and stain resistance. Apply 511 Impregnator to all grout with a paint brush.
Any excess sealer that gets on the surface should be wiped off with a clean towel
before it dries. On larger jobs grout can be sealed by retreating the entire area includ-
3.12.2008
MATERIAL SAFETY DATA SHEET
511 Look Penetrating Sealer
Impregnator
Natural www.miraclesealants.com
Osha鈥檚 Hazard Communication Standard Emergency and First Aid Procedures:
U.S. Department Of Labor Eyes: In case of contact, immediately flush eyes with plenty of water for at
29 CFR 1910.1200 OMB No. 1218-0072 least 15 minutes. Get medical attention if irritation persists.
Identity No: Name: 511 Impregnator
Skin: Remove contaminated clothing and launder before reuse. Wash with
Section 1 soap and water. Get medical attention if irritation persists.
Manufacturers Name: Miracle Sealants Company Ingestion: If swallowed, do not induce vomiting. Get medical attention.
Address: 12318 Lower Azusa Road Never give anything by mouth to an unconscious person.
Emergency Phone: 800-350-1901
Inhalation: If inhaled, remove to fresh air. If breathing is difficult, give oxy-
City: Arcadia
gen. If not breathing, give artificial respiration. Seek medical attention.
State: CA
Phone: 626-443-6433 Section 7 - Precautions for Safe Handling and Use
Date Prepared: March 2008
Steps to be taken in case material is released or spilled: wipe, scrape or
Section 2 - Hazardous Ingredients/Identity Information soak up in an inert material and put in a container for disposal. Wear proper
protective equipment. Remove sources of ignition. Increase area ventila-
Hazardous Components CAS# OSHA PEL ACGIH TLV
tion.
Petroleum Distillate 64741-65-7 100ppm 150ppm
VOC: Less than or equal to 738 g/L Waste disposal method: disposal should be made in accordance with fed-
eral, state and local regulations. Incineration recommended in approved
Section 3 - Physical/Chemical Characteristics
incinerator according to federal, state and local regulations.
Boiling point: 355 - 3950 F Specific gravity: 0.80
Evaporation rate: < 0.1
Vapor pressure (200 C): .5 mm hg Melting point: Not Available Precautions to be taken in handling and storing: use a ground strap. Store
Vapor density (Air=1): 5.3 upright in a cool place below 770 F (400 C). Keep container closed when not
Solubility in water: Insoluble Density: 798 Kg/M3 in use. Avoid breathing vapors. Combustible.
Appearance and odor: Clear, colorless, aromatic liquid.
Other precautions: KEEP OUT OF REACH OF CHILDREN. Follow directions on
Section 4 - Fire And Explosion Hazard Data the container for proper use of this product.
Flash Point: 1250 F (PCC) Flammable limits:
Section 8 - Control Measures
LEL: 1 UEL: 7
pH: Neutral DOT#: Not Available Respiratory protection: Ventilate by opening all doors and windows. If
NFPA Hazard rating H F R S (0-Least, 4-Extreme): 1 2 0 0 exposure above the TLV or PEL require a NIOSH approved respirator
Extinguishing media: Dry chemical, CO2, water fog equipped for the exposure or suitable respiratory protection per
Special fire fighting procedures: Combustible, wear bunker gear and NIOSH 29 CFR 1910.134 is required.
approved breathing apparatus.
Protective gloves: Rubber or plastic, chemical resistant.
Unusual fire and explosion hazards: Cool exposed containers with water to Eye protection: Tight fitting, splash proof safety glasses or goggles.
prevent rupturing. Heat will cause phosgene gas.
Other protective clothing or equipment: Chemical resistant clothing.
Section 5 - Reactivity Data
Work hygienic practices: Wash hands thoroughly before handling food
Stability: Stable stuffs, liquids or tobacco products. Use common sense and care around
Conditions to avoid: Keep away from sources of ignition such as heat, chemicals. Never mix this product with other chemicals. Consult your super-
sparks or open flames. visor for all other hygienic and safety practices. All practices depend on
Incompatible materials to avoid: Oxidizing agent. your specific business. Directions for use normally found on label which will
Hazardous polymerization: Will not occur. dictate engineering and control measures.
Hazardous decomposition products: Carbon monoxide, carbon dioxide, sili-
cone dioxide, fumes of xylene, aromatic and aliphatic hydrocarbons. Section 9 - Shipping & Regulatory Classification
DOT Shipping Name: Please refer to the Bill of Lading receiving/documents
Section 6 - Health Hazard Data
for up-to-date information.
Routes of entry:
Inhalation - Possible
DOT Hazard Class: N/A
Skin - Possible
OSHA Hazard Class: N/A
Ingestion - Possible
UN/NA Number: N/A
Health hazards - Same as signs and symptoms of exposure
OSHA carcinogenicity - None; NTP - None; IARC monographs - None EPA Hazard Waste: D 001, Ignitible
CPSC Classification: Combustible liquid
Signs and symptoms of over exposure
Transportation Class: 55
Eyes:Causes severe eye irritation
Skin: Causes mild skin irritation, drying of the skin. May cause an allergic Toxic Substances Control Act (TSCA): This product and/or all the
skin reaction. ingredients contained in this product have been registered under the
Ingestion: Harmful if swallowed. Causes vomiting, nausea and diarrhea. Toxic Substances Control Act.
Inhalation: Excessive inhalation causes headache, dizziness, nausea and in-
coordination. Harmful if inhaled. SARA: SARA 313 chemicals identified.
Medical conditions aggravated: Respiratory, pulmonary, liver and kidney
NOTE: Miracle Sealants believes the data set forth are accurate. Miracle
disorders. Central nervous systems disorders. Gastrointestinal disorders.
Sealants makes no warranty with respects thereto and disclaims all liability
or reliance thereon. Such data are offered solely for consideration, investi-
gation and verification. Also, the data set forth is for the concentrated fin-
ished product. All lab samples are for experimental purposes only and used
at the customers discretion.
WARR ANT Y & C AUTIONS
Warranty Caution
Instructions are a condensed guide and should not be considered com- 511 Impregnator contains combustible petroleum distillates. All solvents
plete. In the event of failure, the only obligation of Miracle Sealants must be considered toxic and must be used in a well ventilated area. Good
Company shall be to replace such products proven to be defective. Before ventilation means that fresh air is flowing in such a way as to feel a slight
using, user shall determine the suitability of the product for their intended breeze. Open windows and use fans to circulate air. Continue to ventilate
use. User assumes all risks and liability whatsoever in connection therein. until vapors are eliminated. Exposure to high vapor concentration must be
Neither seller nor manufacturer shall be liable for any injury or inability to avoided. Inhaling the vapors can be harmful. Keep away from heat and
use this product. open flames. Avoid prolonged contact with skin. Chemical resistant gloves
should be worn at all times. Keep small children and pets out of the area
3.12.2008
until product or surface has thoroughly dried. Refer to the MSDS for addi-
tional information.
|