MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 1 of 12
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
MEGUIAR'S D130 - DETAILER BODY SOLVENT
SYNONYMS
"Manufacturer's Code: D130"
PRODUCT USE
Cleaning agent.
SUPPLIER
Company: Meguiar' s Australia Pty Ltd
Address:
35 Slough Business Park
Holker St, Silverwater
NSW, 2128
AUS
Telephone: +61 2 9737 9422
Telephone: 1800 804 182
Fax: +61 2 9737 9414
Section 2 - HAZARDS IDENTIFICATION
STATEMENT OF HAZARDOUS NATURE
HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the Criteria of
NOHSC, and the ADG Code.
POISONS SCHEDULE
S5
RISK SAFETY
HARMFUL- May cause lung damage if swallowed. Do not breathe gas/fumes/vapour/spray.
Avoid contact with eyes.
Wear suitable protective clothing.
Use only in well ventilated areas.
Keep container in a well ventilated place.
To clean the floor and all objects contaminated
by this material, use water and detergent.
Keep container tightly closed.
Keep away from food, drink and animal feeding
stuffs.
Take off immediately all contaminated clothing.
In case of contact with eyes, rinse with plenty
of water and contact Doctor or Poisons
Information Centre.
If swallowed, IMMEDIATELY contact Doctor or
Poisons Information Centre. (show this container
or label).
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 2 of 12
Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME CAS RN %
isoparaffins petroleum hydrotreated HFP 64742-47-8. 55-65
petroleum distillates HFP 64742-48-9. 35-45
Section 4 - FIRST AID MEASURES
SWALLOWED
- If swallowed do NOT induce vomiting.
- If vomiting occurs, lean patient forward or place on left side (head-down position, if
possible) to maintain open airway and prevent aspiration.
- Observe the patient carefully.
- Never give liquid to a person showing signs of being sleepy or with reduced awareness;
i.e. becoming unconscious.
- Give water to rinse out mouth, then provide liquid slowly and as much as casualty can
comfortably drink.
- Seek medical advice.
EYE
If this product comes in contact with the eyes:
- Wash out immediately with fresh running water.
- Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and
moving the eyelids by occasionally lifting the upper and lower lids.
- If pain persists or recurs seek medical attention.
- Removal of contact lenses after an eye injury should only be undertaken by skilled
personnel.
SKIN
If skin contact occurs:
- Immediately remove all contaminated clothing, including footwear.
- Flush skin and hair with running water (and soap if available).
- Seek medical attention in event of irritation.
INHALED
- If fumes or combustion products are inhaled remove from contaminated area.
- Lay patient down. Keep warm and rested.
- Prostheses such as false teeth, which may block airway, should be removed, where
possible, prior to initiating first aid procedures.
- Apply artificial respiration if not breathing, preferably with a demand valve
resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if necessary.
- Transport to hospital, or doctor.
NOTES TO PHYSICIAN
Any material aspirated during vomiting may produce lung injury. Therefore emesis should
not be induced mechanically or pharmacologically. Mechanical means should be used if it
is considered necessary to evacuate the stomach contents; these include gastric lavage
after endotracheal intubation. If spontaneous vomiting has occurred after ingestion, the
patient should be monitored for difficult breathing, as adverse effects of aspiration
into the lungs may be delayed up to 48 hours.
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 3 of 12
Section 5 - FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
- Foam.
- Dry chemical powder.
- BCF (where regulations permit).
- Carbon dioxide.
- Water spray or fog - Large fires only.
FIRE FIGHTING
- Alert Fire Brigade and tell them location and nature of hazard.
- Wear full body protective clothing with breathing apparatus.
- Prevent, by any means available, spillage from entering drains or water course.
- Use water delivered as a fine spray to control fire and cool adjacent area.
- Avoid spraying water onto liquid pools.
- DO NOT approach containers suspected to be hot.
- Cool fire exposed containers with water spray from a protected location.
- If safe to do so, remove containers from path of fire.
FIRE/EXPLOSION HAZARD
- Combustible.
- Slight fire hazard when exposed to heat or flame.
- Heating may cause expansion or decomposition leading to violent rupture of containers.
- On combustion, may emit toxic fumes of carbon monoxide (CO).
- May emit acrid smoke.
- Mists containing combustible materials may be explosive.
Combustion products include: carbon dioxide (CO2), other pyrolysis products typical of
burning organic material.
May emit poisonous fumes.
May emit corrosive fumes.
FIRE INCOMPATIBILITY
Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine
bleaches, pool chlorine etc. as ignition may result.
HAZCHEM: None
Personal Protective Equipment
Breathing apparatus.
Chemical splash suit.
Section 6 - ACCIDENTAL RELEASE MEASURES
EMERGENCY PROCEDURES
MINOR SPILLS
- Remove all ignition sources.
- Clean up all spills immediately.
- Avoid breathing vapours and contact with skin and eyes.
- Control personal contact by using protective equipment.
- Contain and absorb spill with sand, earth, inert material or vermiculite.
- Wipe up.
- Place in a suitable labelled container for waste disposal.
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 4 of 12
Section 6 - ACCIDENTAL RELEASE MEASURES
MAJOR SPILLS
Chemical Class: aliphatic hydrocarbons
For release onto land: recommended sorbents listed in order of priority.
SORBENT TYPE RANK APPLICATION COLLECTION LIMITATIONS
LAND SPILL - SMALL
cross- linked 1 shovel shovel R, W, SS
polymer -
particulate
cross- linked 1 throw pitchfork R, DGC, RT
polymer - pillow
wood fiber - 2 throw pitchfork R, P, DGC, RT
pillow
treated wood 2 throw pitchfork DGC, RT
fibre- pillow
sorbent clay - 3 shovel shovel R, I, P
particulate
foamed glass - 3 throw pitchfork R, P, DGC, RT
pillow
LAND SPILL - MEDIUM
cross- linked 1 blower skiploader R, W, SS
polymer -
particulate
cross- linked 2 throw skiploader R, DGC, RT
polymer - pillow
sorbent clay - 3 blower skiploader R, I, P
particulate
polypropylene - 3 blower skiploader W, SS, DGC
particulate
expanded mineral 4 blower skiploader R, I, W, P, DGC
- particulate
polypropylene - 4 throw skiploader DGC, RT
mat
Legend
DGC: Not effective where ground cover is dense
R; Not reusable
I: Not incinerable
P: Effectiveness reduced when rainy
RT:Not effective where terrain is rugged
SS: Not for use within environmentally sensitive sites
W: Effectiveness reduced when windy
Reference: Sorbents for Liquid Hazardous Substance Cleanup and Control;
R.W Melvold et al: Pollution Technology Review No. 150: Noyes Data Corporation 1988.
Moderate hazard.
- Clear area of personnel and move upwind.
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 5 of 12
Section 6 - ACCIDENTAL RELEASE MEASURES
- Alert Fire Brigade and tell them location and nature of hazard.
- Wear breathing apparatus plus protective gloves.
- Prevent, by any means available, spillage from entering drains or water course.
- No smoking, naked lights or ignition sources.
- Increase ventilation.
- Stop leak if safe to do so.
- Contain spill with sand, earth or vermiculite.
- Collect recoverable product into labelled containers for recycling.
- Absorb remaining product with sand, earth or vermiculite.
- Collect solid residues and seal in labelled drums for disposal.
- Wash area and prevent runoff into drains.
- If contamination of drains or waterways occurs, advise emergency services.
EMERGENCY RESPONSE PLANNING GUIDELINES (ERPG)
The maximum airborne concentration below which it is believed that nearly all individuals could be exposed
for up to one hour WITHOUT experiencing or developing
life-threatening health effects is:
petroleum distillates HFP 500 mg/m鲁
irreversible or other serious effects or symptoms which could impair an individual's ability to take
protective action is:
petroleum distillates HFP 50 mg/m鲁
other than mild, transient adverse effects without perceiving a clearly defined odour is:
petroleum distillates HFP 30 mg/m鲁
The threshold concentration below which most people will experience no appreciable risk of health effects:
petroleum distillates HFP 10 mg/m鲁
American Industrial Hygiene Association (AIHA)
Ingredients considered according to the following cutoffs
Very Toxic (T+) >= 0.1% Toxic (T) >= 3.0%
R50 >= 0.25% Corrosive (C) >= 5.0%
R51 >= 2.5%
else >= 10%
where percentage is percentage of ingredient found in the mixture
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
- Containers, even those that have been emptied, may contain explosive vapours.
- Do NOT cut, drill, grind, weld or perform similar operations on or near containers.
- Electrostatic discharge may be generated during pumping - this may result in fire.
- Ensure electrical continuity by bonding and grounding (earthing) all equipment.
- Restrict line velocity during pumping in order to avoid generation of electrostatic
discharge (<=1 m/sec until fill pipe submerged to twice its diameter, then <= 7 m/sec).
- Avoid splash filling.
- Do NOT use compressed air for filling discharging or handling operations.
- Avoid all personal contact, including inhalation.
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 6 of 12
Section 7 - HANDLING AND STORAGE
- Wear protective clothing when risk of exposure occurs.
- Use in a well-ventilated area.
- Prevent concentration in hollows and sumps.
- DO NOT enter confined spaces until atmosphere has been checked.
- Avoid smoking, naked lights or ignition sources.
- Avoid contact with incompatible materials.
- When handling, DO NOT eat, drink or smoke.
- Keep containers securely sealed when not in use.
- Avoid physical damage to containers.
- Always wash hands with soap and water after handling.
- Work clothes should be laundered separately.
- Use good occupational work practice.
- Observe manufacturer's storing and handling recommendations.
- Atmosphere should be regularly checked against established exposure standards to
ensure safe working conditions.
SUITABLE CONTAINER
- Metal can or drum
- Packaging as recommended by manufacturer.
- Check all containers are clearly labelled and free from leaks.
STORAGE INCOMPATIBILITY
Avoid reaction with oxidising agents.
STORAGE REQUIREMENTS
- Store in original containers.
- Keep containers securely sealed.
- No smoking, naked lights or ignition sources.
- Store in a cool, dry, well-ventilated area.
- Store away from incompatible materials and foodstuff containers.
- Protect containers against physical damage and check regularly for leaks.
- Observe manufacturer's storing and handling recommendations.
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
Source Material TWA TWA STEL STEL Peak Peak TWA
ppm mg/m鲁 ppm mg/m鲁 ppm mg/m鲁 F/CC
_________________ __________________ ______ ______ ______ ______ ______ ______ ______
Australia Exposure isoparaffins 5
Standards petroleum
hydrotreated HFP
(Oil mist, refined
mineral)
The following materials had no OELs on our records
鈥? petroleum distillates HFP: CAS:64742-48-9 CAS:64742-88-7
MATERIAL DATA
Sensory irritants are chemicals that produce temporary and undesirable side-effects on
the eyes, nose or throat. Historically occupational exposure standards for these
irritants have been based on observation of workers' responses to various airborne
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 7 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
concentrations. Present day expectations require that nearly every individual should be
protected against even minor sensory irritation and exposure standards are established
using uncertainty factors or safety factors of 5 to 10 or more. On occasion animal no
-observable-effect-levels (NOEL) are used to determine these limits where human results
are unavailable. An additional approach, typically used by the TLV committee (USA) in
determining respiratory standards for this group of chemicals, has been to assign ceiling
values (TLV C) to rapidly acting irritants and to assign short-term exposure limits (TLV
STELs) when the weight of evidence from irritation, bioaccumulation and other endpoints
combine to warrant such a limit. In contrast the MAK Commission (Germany) uses a five
-category system based on intensive odour, local irritation, and elimination half-life.
However this system is being replaced to be consistent with the European Union (EU)
Scientific Committee for Occupational Exposure Limits (SCOEL); this is more closely
allied to that of the USA.
OSHA (USA) concluded that exposure to sensory irritants can:
- cause inflammation
- cause increased susceptibility to other irritants and infectious agents
- lead to permanent injury or dysfunction
- permit greater absorption of hazardous substances and
- acclimate the worker to the irritant warning properties of these substances thus
increasing the risk of overexposure.
INGREDIENT DATA
ISOPARAFFINS PETROLEUM HYDROTREATED HFP:
REL TWA: 300 ppm [EXXON]
for petroleum distillates:
CEL TWA: 500 ppm, 2000 mg/m3 (compare OSHA TWA).
PETROLEUM DISTILLATES HFP:
CEL TWA: 100 ppm, 525 mg/m3 - as Stoddard solvent CCINFO 1441735 - [Shell]
PERSONAL PROTECTION
EYE
- Safety glasses with side shields.
- Chemical goggles.
- Contact lenses may pose a special hazard; soft contact lenses may absorb and
concentrate irritants. A written policy document, describing the wearing of lens or
restrictions on use, should be created for each workplace or task. This should include a
review of lens absorption and adsorption for the class of chemicals in use and an account
of injury experience. Medical and first-aid personnel should be trained in their removal
and suitable equipment should be readily available. In the event of chemical exposure,
begin eye irrigation immediately and remove contact lens as soon as practicable. Lens
should be removed at the first signs of eye redness or irritation - lens should be
removed in a clean environment only after workers have washed hands thoroughly. [CDC
NIOSH Current Intelligence Bulletin 59].
HANDS/FEET
Suitability and durability of glove type is dependent on usage. Factors such as:
- frequency and duration of contact,
- chemical resistance of glove material,
- glove thickness and
- dexterity,
are important in the selection of gloves.
Polyethylene gloves.
Wear chemical protective gloves, eg. PVC.
Wear safety footwear or safety gumboots, eg. Rubber.
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 8 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
OTHER
- Overalls.
- P.V.C. apron.
- Barrier cream.
- Skin cleansing cream.
- Eye wash unit.
RESPIRATOR
Respiratory protection may be required when ANY "Worst Case" vapour-phase concentration
is exceeded (see Computer Prediction in "Exposure Standards").
Protection Factor Half- Face Respirator Full- Face Respirator
10 x ES A- AUS -
A- PAPR- AUS
50 x ES Air- line* -
100 x ES - A- 3
100+ x ES - Air- line**
* - Continuous-flow; ** - Continuous-flow or positive pressure demand
^ - Full-face.
The local concentration of material, quantity and conditions of use determine the type of
personal protective equipment required.
For further information consult site specific
CHEMWATCH data (if available), or your
Occupational Health and Safety Advisor.
ENGINEERING CONTROLS
Local exhaust ventilation usually required. If risk of overexposure exists, wear approved
respirator. Correct fit is essential to obtain adequate protection. Supplied-air type
respirator may be required in special circumstances. Correct fit is essential to ensure
adequate protection.
An approved self contained breathing apparatus (SCBA) may be required in some situations.
Provide adequate ventilation in warehouse or closed storage area.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE
Clear liquid with a sweet odour; insoluble in water.
PHYSICAL PROPERTIES
Liquid.
Does not mix with water.
Floats on water.
Molecular Weight: Not Applicable Boiling Range (掳C): 199
Melting Range (掳C): Not Available Specific Gravity (water=1): 0.92
Solubility in water (g/L): Immiscible pH (as supplied): Not Applicable
pH (1% solution): Not Applicable Vapour Pressure (kPa): Not Available
Volatile Component (%vol): 40 (VOC) Evaporation Rate: <1
Relative Vapour Density (air=1): >1 Flash Point (掳C): 82
Lower Explosive Limit (%): Not Available Upper Explosive Limit (%): Not Available
Autoignition Temp (掳C): Not Available Decomposition Temp (掳C): Not Available
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 9 of 12
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
State: Liquid Viscosity: Not Available
Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION
CONDITIONS CONTRIBUTING TO INSTABILITY
- Presence of incompatible materials.
- Product is considered stable.
- Hazardous polymerisation will not occur.
Section 11 - TOXICOLOGICAL INFORMATION
POTENTIAL HEALTH EFFECTS
ACUTE HEALTH EFFECTS
SWALLOWED
Accidental ingestion of the material may be damaging to the health of the individual.
Swallowing of the liquid may cause aspiration into the lungs with the risk of chemical
pneumonitis; serious consequences may result.
(ICSC13733).
Ingestion of petroleum hydrocarbons may produce irritation of the pharynx, oesophagus,
stomach and small intestine with oedema and mucosal ulceration resulting; symptoms
include a burning sensation in the mouth and throat. Large amounts may produce narcosis
with nausea and vomiting, weakness or dizziness, slow and shallow respiration, swelling
of the abdomen, unconsciousness and convulsions. Myocardial injury may produce
arrhythmias, ventricular fibrillation and electrocardiographic changes. Central nervous
system depression may also occur. Light aromatic hydrocarbons produce a warm, sharp,
tingling sensation on contact with taste buds and may anaesthetise the tongue. Aspiration
into the lungs may produce coughing, gagging and a chemical pneumonitis with pulmonary
oedema and haemorrhage.
EYE
Limited evidence exists, or practical experience suggests, that the material may cause
eye irritation in a substantial number of individuals and/or is expected to produce
significant ocular lesions which are present twenty-four hours or more after instillation
into the eye(s) of experimental animals. Repeated or prolonged eye contact may cause
inflammation characterised by temporary redness (similar to windburn) of the conjunctiva
(conjunctivitis);
temporary impairment of vision and/or other transient eye damage/ulceration may occur.
Petroleum hydrocarbons may produce pain after direct contact with the eyes. Slight, but
transient disturbances of the corneal epithelium may also result. The aromatic fraction
may produce irritation and lachrymation.
SKIN
Skin contact with the material may damage the health of the individual; systemic effects
may result following absorption.
The liquid may be miscible with fats or oils and may degrease the skin, producing a skin
reaction described as non-allergic contact dermatitis. The material is unlikely to
produce an irritant dermatitis as described in EC Directives .
Repeated exposure may cause skin cracking, flaking or drying following normal handling
and use.
Entry into the blood-stream, through, for example, cuts, abrasions or lesions, may
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 10 of 12
Section 11 - TOXICOLOGICAL INFORMATION
produce systemic injury with harmful effects. Examine the skin prior to the use of the
material and ensure that any external damage is suitably protected.
INHALED
Inhalation of vapours or aerosols (mists, fumes), generated by the material during the
course of normal handling, may be damaging to the health of the individual.
Limited evidence or practical experience suggests that the material may produce
irritation of the respiratory system, in a significant number of individuals, following
inhalation. In contrast to most organs, the lung is able to respond to a chemical insult
by first removing or neutralising the irritant and then repairing the damage. The repair
process, which initially evolved to protect mammalian lungs from foreign matter and
antigens, may however, produce further lung damage resulting in the impairment of gas
exchange, the primary function of the lungs. Respiratory tract irritation often results
in an inflammatory response involving the recruitment and activation of many cell types,
mainly derived from the vascular system.
Inhalation hazard is increased at higher temperatures.
Inhalation of vapours may cause drowsiness and dizziness. This may be accompanied by
narcosis, reduced alertness, loss of reflexes, lack of coordination and vertigo.
If exposure to highly concentrated solvent atmosphere is prolonged this may lead to
narcosis, unconsciousness, even coma and possible death.
Acute effects from inhalation of high vapour concentrations may be chest and nasal
irritation with coughing, sneezing, headache and even nausea.
CHRONIC HEALTH EFFECTS
Limited evidence suggests that repeated or long-term occupational exposure may produce
cumulative health effects involving organs or biochemical systems.
Chronic solvent inhalation exposures may result in nervous system impairment
and liver and blood changes. [PATTYS].
Repeated or prolonged exposure to mixed hydrocarbons may produce narcosis with dizziness,
weakness, irritability, concentration and/or memory loss, tremor in the fingers and
tongue, vertigo, olfactory disorders, constriction of visual field, paraesthesias of the
extremities, weight loss and anaemia and degenerative changes in the liver and kidney.
Chronic exposure by petroleum workers, to the lighter hydrocarbons, has been associated
with visual disturbances, damage to the central nervous system, peripheral neuropathies
(including numbness and paraesthesias), psychological and neurophysiological deficits,
bone marrow toxicities (including hypoplasia possibly due to benzene) and hepatic and
renal involvement. Chronic dermal exposure to petroleum hydrocarbons may result in
defatting which produces localised dermatoses. Surface cracking and erosion may also
increase susceptibility to infection by microorganisms. One epidemiological study of
petroleum refinery workers has reported elevations in standard mortality ratios for skin
cancer along with a dose-response relationship indicating an association between routine
workplace exposure to petroleum or one of its constituents and skin cancer, particularly
melanoma. Other studies have been unable to confirm this finding.
TOXICITY AND IRRITATION
Not available. Refer to individual constituents.
ISOPARAFFINS PETROLEUM HYDROTREATED HFP:
No significant acute toxicological data identified in literature search.
PETROLEUM DISTILLATES HFP:
data for CAS 64742-88-7 i.e. CCINFO record 1441735
Oral (rat) LD50: >8.0 mL/Kg = 6288 mg/kg No data.
Dermal (rat)LD50: >4.0 mL/kg = 3144 mg/kg
Inhalation (rat) LD50: 1400 ppm/4h [Shell - Canada]
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 11 of 12
Section 11 - TOXICOLOGICAL INFORMATION
Section 12 - ECOLOGICAL INFORMATION
Drinking Water Standards:
hydrocarbon total: 10 ug/l (UK max.).
DO NOT discharge into sewer or waterways.
Section 13 - DISPOSAL CONSIDERATIONS
- Recycle wherever possible or consult manufacturer for recycling options.
- Consult State Land Waste Authority for disposal.
- Bury or incinerate residue at an approved site.
- Recycle containers if possible, or dispose of in an authorised landfill.
Section 14 - TRANSPORTATION INFORMATION
HAZCHEM: None
NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS:UN, IATA,
IMDG
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE: S5
REGULATIONS
isoparaffins petroleum hydrotreated HFP (CAS: 64742-47-8) is found on the following
regulatory lists;
Australia Exposure Standards
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
Australia Poisons Schedule
International Council of Chemical Associations (ICCA) - High Production Volume List
OECD Representative List of High Production Volume (HPV) Chemicals
petroleum distillates HFP (CAS: 64742-48-9) is found on the following regulatory lists;
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
Australia Poisons Schedule
International Council of Chemical Associations (ICCA) - High Production Volume List
OECD Representative List of High Production Volume (HPV) Chemicals
petroleum distillates HFP (CAS: 64742-88-7) is found on the following regulatory lists;
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
Australia Poisons Schedule
International Council of Chemical Associations (ICCA) - High Production Volume List
OECD Representative List of High Production Volume (HPV) Chemicals
continued...
MEGUIAR'S D130 - DETAILER BODY SOLVENT
Chemwatch Material Safety Data Sheet
Issue Date: 3-Jan-2007 CHEMWATCH 6100-58
NA317EC CD 2006/4 Page 12 of 12
Section 16 - OTHER INFORMATION
INGREDIENTS WITH MULTIPLE CAS NUMBERS
Ingredient Name CAS
petroleum 64742- 48- 9, 64742- 88- 7
distillates HFP
EXPOSURE STANDARD FOR MIXTURES
"Worst Case" computer-aided prediction of vapour components/concentrations:
Composite Exposure Standard for Mixture (TWA) (mg/m3): 525 mg/m鲁
If the breathing zone concentration of ANY of the components listed below is exceeded,
"Worst Case" considerations deem the individual to be overexposed.
Component Breathing Zone ppm Breathing Zone mg/m3 Mixture Conc: (%).
Component Breathing zone Breathing Zone Mixture Conc
(ppm) (mg/m鲁) (%)
petroleum distillates HFP 100.00 525.0000 45.0
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written permission
from CHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: 3-Jan-2007
Print Date: 3-Jan-2007
|