MSDS CAS# N/A amresupply_com_brite

MSDS		Material Safety Data Sheet

CAS		N/A

File Name	:	amresupply_com_brite_silver.asp

2.41

Industrial

THE

SHER WIN-WILLIAMS

COMPANY

and SILVER-BRITE®

Marine ALUMINUM PAINT

Coatings B59S11

INDUSTRIAL

PRODUCT INFORMATION

& MARINE Revised 3/2001

COATINGS

PRODUCT DESCRIPTION RECOMMENDED USES

SILVER-BRITE ALUMINUM PAINT is a superior quality, one For use over prepared steel surfaces in normal and high tem-

package, interior/exterior, general purpose aluminum paint for- perature (up to 400°F) environments.

mulated with 325-mesh leafing aluminum pigment, petroleum

�? Interior/exterior �? Metal built-up roofs

resin, and select oils producing a chrome-like uniform appear-

�? Piping �? Refineries

ance.

�? Radiators �? Siding

�? Bridges �? Storage tank exteriors

�? For service temperatures up to 400°F

�? Fences

�? Resists discoloration

�? Long term protection against weathering and moisture

�? Conforms to AWWA D102-97 Outside Coating Systems

#1-A and #2-A

PRODUCT CHARACTERISTICS PERFORMANCE CHARACTERISTICS

Finish: Aluminum Sheen �? Heat reflective

Color: Aluminum �? Dry heat resistant to 400°F

Volume Solids: 41% ± 2% �? Long term protection against weathering and moisture

Weight Solids: 52% ± 2% �? Ultraviolet light resistant

VOC (EPA Method 24): 450 g/L; 3.8 lb/gal �? Maintains "sheen"

Recommended Spreading Rate per coat: Provides performance comparable to products formulated to

Wet mils: 2.5 - 3.5 specification: SSPC-Paint 101

Dry mils: 1.0 - 1.5 (critical)

Coverage: 438 - 658 sq ft/gal approximate

Drying Schedule @ 3.0 mils wet @ 50% RH:

@50°F @ 77°F @100°F

To touch: 4 hours 1-4 hours 30 minutes

Tack free: 8 hours 6-8 hours 2 hours

To recoat: 28 hours 24 hours 10 hours

To cure: 10 days 8 days 3 days

Drying time is temperature, humidity and film thickness dependent.

Shelf Life: 36 months, unopened, at 77°F

Flash Point: 88°F, PMCC

Reducer/Clean Up: Mineral Spirits, R1K4, clean up only

Alkyd 2.41 2000096 continued on back

2.41

Industrial

THE

SHER WIN-WILLIAMS

COMPANY

and SILVER-BRITE®

Marine ALUMINUM PAINT

Coatings B59S11

INDUSTRIAL

PRODUCT INFORMATION

& MARINE

COATINGS

RECOMMENDED SYSTEMS SURFACE PREPARATION

Steel, 200°F-400°F: Surface must be clean, dry, and in sound condition. Remove

2 cts. Silver-Brite Aluminum Paint @ 1.0 - 1.5 mil dft/ct all oil, dust, grease, dirt, loose rust, and other foreign material

to ensure adequate adhesion.

Steel, rusted, below 200°F:

1 ct. Kem Bond HS @ 2.0 - 5.0 mils dft Refer to product Application Bulletin for detailed surface prepa-

2 cts. Silver-Brite Aluminum Paint @ 1.0 - 1.5 mil dft/ct ration information.

Aluminum, below 200°F: Minimum recommended surface preparation:

1 ct. DTM Wash Primer @ 0.7 - 1.3 mils dft Iron & Steel: SSPC-SP6, 1 mil profile

2 cts. Silver-Brite Aluminum Paint @ 1.0 - 1.5 mil dft/ct * Aluminum: SSPC-SP1

* Galvanizing: SSPC-SP1

Concrete, below 200°F: * Concrete & Masonry: SSPC-SP13/NACE 6

1 ct. Heavy Duty Block Filler @ 10.0 - 18.0 mils dft

2 cts. Silver-Brite Aluminum Paint @ 1.0 - 1.5 mil dft/ct * Primer required

COLOR AVAILABILITY/TINTING

Galvanized Metal, below 200°F:

1 ct. Galvite HS @ 3.0-4.5 mils dft

Do not tint.

2 cts. Silver-Brite Aluminum Paint @ 1.0 -1 .5 mil dft/ct

Color: Aluminum

Insulated Pipe and Ductwork, interior below 130°F:

1 ct. PrepRite 200 Latex Primer @ 1.5 mils dft

2 cts. Silver-Brite Aluminum Paint @ 1.0 - 1.5 mil dft/ct

Masonry, below 200°F:

1 ct. Masonry Conditioner

APPLICATION CONDITIONS

(Follow application recommendations)

2 cts. Silver-Brite Aluminum Paint @ 1.0 - 1.5 mil dft/ct

Temperature: 40°F minimum, 120°F maximum

(air, surface, and material)

At least 5°F above dew point

Relative humidity: 85% maximum

Refer to product Application Bulletin for detailed application

information.

ORDERING INFORMATION

Packaging: 1 and 5 gallon containers

Weight per gallon: 7.82 ± 0.2 lb

SAFETY PRECAUTIONS

Refer to the MSDS sheet before use.

Published technical data and instructions are subject to change

without notice. Contact your Sherwin-Williams representative

The systems listed above are representative of the product's

for additional technical data and instructions.

use. Other systems may be appropriate.

2.41A

Industrial

THE

SHER WIN-WILLIAMS

COMPANY

and SILVER-BRITE®

Marine ALUMINUM PAINT

Coatings B59S11

INDUSTRIAL

APPLICATION BULLETIN

& MARINE Revised 3/2001

COATINGS

SURFACE PREPARATION APPLICATION CONDITIONS

Surface must be dry, and in sound condition. Remove all oil, Temperature: 40°F minimum, 120°F maximum

dust, grease, dirt, loose rust, peeling paint, and other con- (air, surface, and material)

taminants to ensure adequate adhesion. At least 5°F above dew point

Iron & Steel (below 200°F)

Relative humidity: 85% maximum

Remove all oil and grease from the surface by Solvent Clean-

ing per SSPC-SP1. Minimum surface preparation is Commer-

cial Blast Cleaning per SSPC-SP6, Kem Bond SSPC-SP2

1 mil profile. Use Kem Bond HS Primer.

Iron & Steel (200°F-400°F) APPLICATION EQUIPMENT

Remove all oil and grease from the surface by Solvent Clean-

ing per SSPC-SP1. Minimum surface preparation is Near White The following is a guide. Changes in pressures and tip sizes

Blast Cleaning per SSPC-SP10, 1 mil profile. Apply two coats may be needed for proper spray characteristics. Always purge

Silver-Brite Aluminum Paint.

spray equipment before use with listed reducer. Any reduction

must be compatible with the existing environmental and appli-

Aluminum (below 200°F)

Remove all oil, grease, dirt, oxide, and other foreign material cation conditions.

by Solvent Cleaning per SSPC-SP1. Primer required.

Reducer/Cleanup ............. Mineral Spirits, R1K4, clean up only

Concrete (below 200°F)

For surface preparation, refer to SSPC-SP13/NACE 6. Sur- Airless Spray

face should be thoroughly clean and dry. Air, surface, and Pressure .......................... 2000 psi

material temperature must be at least 55°F before filling. Use

Hose ................................. 1/4" ID

Heavy Duty Block Filler. The filler must be thoroughly dry be- Tip ..................................... .010 - .012"

fore topcoating per manufacturer's recommendations.

Reduction ........................ not recommended

Galvanized Metal (below 200°F)

Allow to weather a minimum of six months prior to coating. Conventional Spray

Solvent Clean per SSPC-SP1. Prime with Galvite HS. When Gun .................................. Binks 95

weathering is not possible, or the surface has been treated Fluid Nozzle .................... 63C

with chromates or silicates, first Solvent Clean per SSPC-SP1 Air Nozzle ........................ 63PB

and apply a test patch of a primer coat. Allow paint to dry at Atomization Pressure .... 50 psi

least one week before testing adhesion. If adhesion is poor,

Fluid Pressure ................ 20 psi

brush blasting per SSPC-SP7 is necessary to remove these

Reduction ........................ not recommended

treatments. Rusty galvanizing below 200°F requires a mini-

mum of Hand Tool Cleaning per SSPC-SP2. Primer required.

Brush

Insulated Pipe & Ductwork (interior below 130°F) Brush................................ Natural Bristle

Prime with PrepRite 200 Latex Wall Primer. Reduction ........................ not recommended

NOTE: For insulated pipe and ductwork 130°F to 400°F, ap-

ply two coats Silver-Brite Aluminum Paint direct to surface.

Roller

Cover ............................... 1/4" woven with phenolic core

Masonry

Reduction ........................ not recommended

All masonry must be free of dirt, oil, grease, masonry dust,

etc. Special care should be exercised while using this product

for maximum performance. Film thickness and surface prepa- If specific application equipment is listed above, equivalent

ration are critical. Be especially concerned at lap areas and equipment may be substituted.

when using airless spray. Excessive film thickness will cause

blistering and peeling. Insufficient film thickness may lead to

premature failure of the coating. Always apply to cool sur-

faces (50°F-100°F).

Previously Painted Surfaces (below 200°F)

If in sound condition, clean the surface of all foreign material.

Spot primer bare areas with recommended primer. If paint is

peeling or badly weathered, clean surface to sound substrate

and treat as a new surface.

Alkyd 2.41A 2000096A continued on back

2.41A

Industrial

THE

SHER WIN-WILLIAMS

COMPANY

and SILVER-BRITE®

Marine ALUMINUM PAINT

Coatings B59S11

INDUSTRIAL

APPLICATION BULLETIN

& MARINE

COATINGS

APPLICATION PROCEDURES PERFORMANCE TIPS

Surface preparation must be completed as indicated. Stripe coat all crevices, welds and sharp angles to prevent

early failure in these areas.

Lightly stir before use. Do not shake with mechanical shaker

or overly agitate, as a dull, nonuniform, mottled appearance When using spray application, use a 50% overlap with each

will result. pass of the gun to avoid holidays, bare areas, and pinholes. If

necessary, cross spray at a right angle.

For best results, apply to a cool surface between 50°F -100°F.

Spreading rates are calculated on volume solids and do not

Apply paint at the recommended film thickness and spreading include an application loss factor due to surface profile, rough-

rate as indicated below: ness or porosity of the surface, skill and technique of the ap-

plicator, method of application, various surface irregularities,

Recommended Spreading Rate per coat: material lost during mixing, spillage, overthinning, climatic con-

Wet mils: 2.5-3.5 ditions, and excessive film build.

Dry mils: 1.0-1.5 critical

Coverage: 436-658 sq ft/gal approximate No reduction of material is recommended as it can affect film

build, appearance, and adhesion.

Drying Schedule @ 3.0 mils wet @ 50% RH:

@50°F @ 77°F @100°F In order to avoid blockage of spray equipment, clean equip-

To touch: 4 hours 1-4 hours 30 minutes ment before use or before periods of extended downtime with

Tack free: 8 hours 6-8 hours 2 hours Mineral Spirits, R1K4.

To recoat: 28 hours 24 hours 10 hours

To cure: 10 days 8 days 3 days For best results, apply to a cool surface between 50°F -100°F.

Drying time is temperature, humidity and film thickness dependent. Do not apply greater than 1.5 mils dft/ct

Special care should be exercised while using this product for Refer to Product Information sheet for additional performance

maximum performance. Film thickness and surface prepara- characteristics and properties.

tion are critical. Be especially concerned at lap areas and

when using airless spray. Excessive film thickness will cause

blistering and peeling. Insufficient film thickness may lead to

premature rusting of the surface.

Application of coating above maximum or below minimum rec-

ommended spreading rate may adversely affect coating per-

formance.

CLEAN UP INSTRUCTIONS SAFETY PRECAUTIONS

Clean spills and spatters immediately with Mineral Spirits, Refer to the MSDS sheet before use.

R1K4. Clean tools immediately after use with Mineral Spirits,

R1K4. Follow manufacturer's safety recommendations when Published technical data and instructions are subject to change

using any solvent. without notice. Contact your Sherwin-Williams representative

for additional technical data and instructions.

ALL Chemical Analysis PAGES IN THIS GROUP

NAME	CAS
ambion_com_msds_1005.asp	N/A
56-81-5.asp	56-81-5
ambion_com_msds_1910.asp	N/A
ambion_com_msds_1926.asp	N/A
ambion_com_msds_4386995.asp	N/A
64-17-5.asp	64-17-5
56-81-5.asp	56-81-5
7791-18-6.asp	7791-18-6
127-08-2.asp	127-08-2
108-95-2.asp	108-95-2
6131-90-4.asp	6131-90-4
75-45-6.asp	75-45-6 101-68-8 9016-87-9
amcsupplies_com_au_AccuCastIBG2002MSDS.asp	N/A
298-14-6.asp	298-14-6
7647-01-0.asp	7647-01-0
11-13-0.asp	11-13-0 12-05-0
03-13-0.asp	03-13-0 06-21-0
03-01-0.asp	03-01-0 12-27-0
111-76-2.asp	111-76-2 141-43-5
07-02-2.asp	07-02-2 68603-42-9 25155-30-0 52-51-7
amerigel_com_MSDSCL.asp	N/A
65997-17-3.asp	65997-17-3 25104-55-6 50-00-0
7772-99-8.asp	7772-99-8
06-12-0.asp	06-12-0 13463-67-7 471-34-1 7732-18-5
108-95-2.asp	108-95-2 50-00-0 100-51-6
7631-86-9.asp	7631-86-9 9003-35-4 108-95-2 50-00-0 64-17-5 108-10-1
1303-33-9.asp	1303-33-9
7440-42-8.asp	7440-42-8 7440-47-3 7439-89-6 7440-02-0 7440-21-3
84775-71-3.asp	84775-71-3
amphorawholesale_com_425.asp	N/A
110-54-3.asp	110-54-3 110-82-7 74-98-6 75-28-5 115-10-6
amresupply_com_brite_silver.asp	N/A
64742-54-7.asp	64742-54-7 111-76-2 64742-88-7
57-55-6.asp	57-55-6
amsoil_com_gxc.asp	N/A
ams_usda_gov_SoyProteinIsolateAmndmnt1.asp	N/A
amtechuk_biz_Pro400.asp	N/A
analyticon_de_MSDS.asp	N/A
9002-93-1.asp	9002-93-1
114162-64-0.asp	114162-64-0
151-21-3.asp	151-21-3
andersonsgolfproducts_com_AGC131WDG4_msds.asp	N/A
anglomoil_com_au_MSDS_G2163_660128.asp	N/A
anglomoil_com_au_MSDS_Machine_Oil__Chemwatch_49638.asp	N/A
anglomoil_com_MSDS_SFG_Hydraulic_3268_ChemWatch_462182.asp	N/A
anglomoil_com_MSDS_Triple_S_90__Chemwatch_468878.asp	N/A
69-65-8.asp	69-65-8 9005-65-6
50-40-6.asp	50-40-6 85721-33-1 7647-14-5
annovireverberi_com_MSDS_AR64516_Triples_Plunger_Pump_Oil.asp	N/A
annovireverberi_com_MSDS_AR64545_Crankcase_Oil.asp	N/A

HBCChem,Inc

Chemical Information Net chemcas.orgCopyright Reserved

Trading Lead

Leputech HPLC Laboratory