Mystik?DOT 3 Brake Fluid
Material Safety Data Sheet
CITGO Petroleum Corporation
663603002
MSDS No.
P.O. Box 3758
Hazard Rankings
Tulsa, OK 74102-3758
Revision Date 07/14/1999
HMIS NFPA
IMPORTANT: Read this MSDS before handling or disposing of this product and pass this information on to 2 2
Health Hazard
employees, customers and users of this product.
1 1
Fire Hazard
Emergency Overview 0
Reactivity 0
Liquid.
Physical State
* = Chronic Health Hazard
Clear to light amber. Mild.
Color Odor
WARNING: Protective Equipment
Harmful or Fatal if Swallowed.
Minimum Requirements
Can Cause Liver and Kidney Damage.
See Section 8 for Details
Can be absorbed through the skin.
Can cause eye and skin irritation.
Overexposure to vapor can cause temporary blurring of vision.
Spills can cause slipping hazard.
SECTION 1: IDENTIFICATION
Mystik?DOT 3 Brake Fluid (918) 495-5933
Trade Name Technical Contact
(918) 495-4700
Product Number 663603002 Medical Emergency
Mixture (800) 424-9300
CAS Number CHEMTREC Emergency
Specialty Oil
Product Family
Brake Fluid;
Synonyms
Former ILS Code: 63603;
Legacy Code No.: 7069X001;
CITGO SAP Product Code No.: 663603003
SECTION 2: COMPOSITION
Concentration (%)
Component Name(s) CAS Registry No.
1) Triethylene glycol monobutyl ether 143-22-6 45 - 55
2) Diethylene glycol monobutyl ether 112-34-5 20 - 30
3) Diethylene Glycol 111-46-6 1 - 10
4) Diethylene glycol monopropyl ether 6881-94-3 1-5
5) Diethylene glycol monoethyl ether 111-90-0 1-5
6) Triethylene glycol monoethyl ether 112-50-5 1-5
SECTION 3: HAZARDS IDENTIFICATION
Also see Emergency Overview and Hazard Ratings on the top of Page 1 of this MSDS.
Major Route(s) of Entry Skin contact. Eye Contact.
Signs and Symptoms of Acute Exposure
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 1
Continued on Next Page
Mystik?DOT 3 Brake Fluid
Overexposure to glycol and glycol ether vapors or mists can cause respiratory tract irritation. In general,
Inhalation
this effect becomes noticable with airborne concentrations of approximately 60 ppm. Cough and a burning
sensation in the trachea are symptoms of inhalation exposures above 80 ppm. Overexposure to glycols
and glycol ethers can cause central nervous system depression. Symptoms include headache, weakness,
nausea, vomiting, dizziness, loss of coordination and increased heart rate. Seisures, convulsions, coma
and death are possible at extremely high concentrations.
This product can cause moderate eye irritation with short-term contact with liquid or sprays. Also, this
Eye Contact
product can cause redness, tearing and blurred vission.
This product can cause mild, transient skin irritation with short-term exposure. This material may be
Skin Contact
absorbed through the skin.
The predominant hazard associated with this product is ingestion of large quantities at a single time.
Ingestion
During the first 12 hours, the patient may experience central nervous system effects such as headache,
weakness, nausea, dizziness, loss of judgement and coordination. In mild cases, the patient may appear
to be drunk but without the breath odor of alcohol. In more severe cases the patient will experience
cardiopulmonary symptoms including mild high blood pressure, abnormally fast heartbeat and elevated
breathing rate. Convulsions and coma are possible. Kidney complications, including slow or no
production of urine may be expected 24 to 72 hours after ingestion.
Certain glycols and glycol ethers have been associated with birth defects in laboratory animals at doses
Chronic Health Effects
Summary which were toxic to the mother. In repeated exposure studies, certain glycols produced skin irritation and
severe eye irritation with corneal damage in laboratory animals. Chronic ingestion studies with lower
molecular weight glycols resulted in kidney damage with calcium deposits. Also, calcium oxalate crystals
were identified in brain tissue of experimental animals. Limited information is available regarding the
effects of chronic inhalation of glycol and glycol ethers in humans.
Persons with preexisting kidney or liver diseases may have their conditions aggravated by ingestion of or
Conditions Aggravated
by Exposure overexposure to this product.
Kidneys, Liver, Skin, Eyes, Central Nervous System (CNS).
Target Organs
This product does not contain any components at concentrations above 0.1% which are considered
Carcinogenic Potential
carcinogenic by OSHA, IARC, or NTP.
OSHA Hazard Classification is indicated by an "X" in the box adjacent to the hazard title. If no "X" is present, the product does not exhibit the
hazard as defined in the OSHA Hazard Communication Standard (29 CFR 1910.1200).
OSHA Health Hazard Classification OSHA Physical Hazard Classification
Explosive Pyrophoric
Irritant Toxic Combustible
Oxidizer Water-reactive
Sensitizer Highly Toxic Flammable
Carcinogenic Organic Peroxide Unstable
Corrosive Compressed Gas
SECTION 4: FIRST AID MEASURES
Take proper precautions to ensure your own health and safety before attempting rescue or providing first aid. For more specific
information, refer to Exposure Controls and Personal Protection in Section 8 of this MSDS.
Move victim to fresh air. If victim is not breathing, immediately begin rescue breathing. If breathing is
Inhalation
difficult, 100 percent humidified oxygen should be administered by a qualified individual. Seek medical
attention immediately. Keep the affected individual warm and at rest.
Check for and remove contact lenses. If irritation or redness develops, flush eyes with cool, clean,
Eye Contact
low-pressure water for at least 15 minutes. Hold eyelids apart to ensure complete irrigation of the eye
and eyelid tissue. Do not use eye ointment. Seek medical attention immediately.
If liquid contact the skin, rinse the exposed area with water. Remove contaminated clothing. Seek
Skin Contact
medical attention if skin irritation or pain persists. Wash contaminated clothing before reuse. Discard
contaminated leather goods such as gloves and shoes.
If swallowed, give two glasses of water to drink. Never give anything by mouth to a person who is not
Ingestion
fully conscious. Induce vomiting only upon the advise of a physician. Seek medical attention
immediately.
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 2
Continued on Next Page
Mystik?DOT 3 Brake Fluid
Ingestion of lower molcular weight glycols have produced an accumulation of glycolate and glyoxalate
Notes to Physician
which form lactate and results in metabolic acidosis, renal failure, heart failure, and pulmonary edema.
Kidney insufficiency has been reported after two to three days of ingestion. The kidney failure may be
caused by accumulation of calcium oxalate crystals. Crystalluria can be an early sign of glycol
poisoning.
The decision to induce or not to induce emesis in ingestions must be carefully considered. Measures to
decrease absorption may be useful. If the patient has signs of esophageal or gastrointestinal tract
irritation or burns, or has evidence of a decreased sensorium, a depressed gag reflex, or impending
shock, induced emesis should be avoided.
SECTION 5: FIRE FIGHTING MEASURES
OSHA/NFPA Class-IIIB combustible liquid. Slightly combustible!
NFPA Flammability
Classification
OPEN CUP: 121癈 (250癋) (Estimated).
Flash Point Method
No data. No data.
Lower Flammable Limit Upper Flammable Limit
Not available.
Autoignition Temperature
Combustion gases may contain CO, CO2, irritating and acrid combustion products.
Hazardous
Combustion Products
When heated above its flash point temperature, this material will release vapors which, if exposed to an
Special Properties
ignition source, can ignite. In enclosed spaces vapors can ignite with explosive force. Mists or sprays
may burn at temperatures below the flash point.
Use dry chemical, "alcohol" foam, Carbon Dioxide or Halon.
Extinguishing Media
Firefighters must use full bunker gear including NIOSH-approved positive pressure self-contained
Fire Fighting Protective
Clothing breathing apparatus to protect against potential hazardous combustion or decomposition products and
oxygen deficiencies. Withdraw immediately from the area if there is a rising sound from a venting safety
device or discoloration of vessels, tanks, or pipelines.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Take proper precautions to ensure your own health and safety before attempting spill control or clean-up. For more specific
information, refer to the Emergency Overview on Page 1, Exposure Controls and Personal Protection in Section 8 and Disposal
Considerations in Section 13 of this MSDS.
Do not touch damaged containers or spilled material unless wearing appropriate protective equipment.
Slipping hazard; do not walk through spilled material. Stop leak if you can do so without risk. For small
spills, absorb or cover with dry earth, sand, or other inert non-combustible absorbent material and place
into waste containers for later disposal. Contain large spills to maximize product recovery or disposal.
Prevent entry into waterways or sewers. In urban area, cleanup spill as soon as possible. In natural
environments, seek cleanup advice from specialists to minimize physical habitat damage. This material
is miscible in water. Absorbent pads and similar materials can be used. Comply with all laws and
regulations.
SECTION 7: HANDLING AND STORAGE
Avoid water contamination and extreme temperatures to minimize product degradation. Empty
Handling
containers may contain product residues that can ignite with explosive force. Do not pressurize, cut,
weld, braze solder, drill, grind or expose containers to flames, sparks, heat or other potential ignition
sources. Consult appropriate federal, state and local authorities before reusing, reconditioning,
reclaiming, recycling or disposing of empty containers and/or waste residues of this product.
Store in resin-coated, stainless steel or aluminum containers. Iron containers are acceptable for short
Storage
durations although lower molecular weight glycols can cause corrosion. Keep containers tightly closed to
avoid moisture. Protect against physical damage. Keep separate from o strong oxidizing agents. Avoid
exposure to open flame, fire or extreme heat. Do not store at temperatures above 120?F or in direct
sunlight for extended periods of time. Consult appropriate federal, state and local authorities before
reusing, reconditioning, reclaiming, recycling or disposing of empty containers or waste residues of this
product.
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 3
Continued on Next Page
Mystik?DOT 3 Brake Fluid
SECTION 8: EXPOSURE CONTROLS AND PERSONAL PROTECTION
Engineering Controls Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of mists
and/or vapors below the recommended exposure limits (see below). An eye wash station and safety
shower should be located near the work-station.
Personal Protective Personal protective equipment should be selected based upon the conditions under which this material is
Equipment used. A hazard assessment of the work area for PPE requirements should be conducted by a qualified
professional pursuant to OSHA regulations. The following pictograms represent the minimum
requirements for personal protective equipment. For certain operations, additional PPE may be required.
Safety glasses equipped with side shields should be adequate protection under most conditions of use.
Eye Protection
Wear goggles and/or face shield if splashing or spraying is likely, especially if material is heated above
125癋 (or 51癈). Have suitable eye wash water available.
Use gloves constructed of glycol-resistant materials such as butyl rubber if frequent or prolonged
Hand Protection
contact is expected. Use heat-protective gloves when handling product at elevated temperatures.
Use clean and impervious protective clothing (e.g., neoprene or Tyvek? if splashing or spraying
Body Protection
conditions are present. Protective clothing may include long-sleeve outer garment, apron, or lab coat.
If significant contact occurs, remove oil-contaminated clothing as soon as possible and promptly
shower. Launder contaminated before reuse or discard. Wear heat protective boots and protective
clothing when handling material at elevated temperatures.
Vaporization or misting is not expected at ambient temperatures. Therefore, the need for respiratory
Respiratory Protection
protection is not anticipated under normal use conditions and with adequate ventilation. If elevated
airborne concentrations above applicable workplace exposure levels are anticipated, a
NIOSH-approved organic vapor respirator equipped with a dust/mist prefilter should be used.
Protection factors vary depending upon the type of respirator used. Respirators should be used in
accordance with OSHA requirements (29 CFR 1910.134).
Use good personal hygiene practices. Wash hands and other exposed skin areas with plenty of mild
General Comments
soap and water before eating, drinking, smoking, use of toilet facilities, or leaving work. DO NOT use
gasoline, kerosene, solvents, or harsh abrasive skin cleaners.
Occupational Exposure Guidelines
Substance Applicable Workplace Exposure Levels
TWA: 10 (mg/M3) from AIHA (WEEL)
1) Diethylene glycol
2) Diethylene glycol monoethyl ether TWA: 25 (ppm) from AIHA (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Clear to light amber. Mild.
Odor
Color
Liquid.
Physical State
GT 1 (Air = 1)
Vapor Density
Not applicable.
1.03 (Water = 1) pH
Specific Gravity
205癈 (401癋) Not available.
Melting/Freezing Point
Boiling Point/Range
LT 1 mm of Hg (@ 20癈) Not available.
Vapor Pressure Viscosity (cSt @ 40癈)
Easily soluble in cold water, hot water. Volatile Characteristics Slightly volatile.
Solubility in Water
Additional Properties Density = 8.62 Lbs/gal.
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 4
Continued on Next Page
Mystik?DOT 3 Brake Fluid
SECTION 10: STABILITY AND REACTIVITY
Hazardous Polymerization Not expected to occur.
Stable.
Chemical Stability
Keep away from extreme heat, sparks, open flame, and strongly oxidizing conditions.
Conditions to Avoid
Oxygen and strong oxidizers.
Materials Incompatibility
No additional hazardous decomposition products were identified other than the combustion products
Hazardous
Decomposition Products identified in Section 5 of this MSDS.
SECTION 11: TOXICOLOGICAL INFORMATION
For other health-related information, refer to the Emergency Overview on Page 1 and the Hazards Identification in Section 3 of this
MSDS.
Toxicity Data Triethylene glycol monobutyl ether:
ORAL (LD50): Acute: 5300 mg/kg [Rat].
Diethylene glycol monobutyl ether:
ORAL (LD50): Acute: 2000 mg/kg [Guinea pig]. 5660 mg/kg [Rat]. 2200 mg/kg [Rabbit].
Diethylene glycol:
ORAL (LD50): Acute: 12565 mg/kg [Rat]. 13300 mg/kg [Mouse]. 2690 mg/kg [Rabbit].
DERMAL (LD50): Acute: 11890 mg/kg [Rabbit].
Diethylene glycol monoethyl ether:
ORAL (LD50): Acute: 5400 mg/kg [Rat]. 6500 mg/kg [Mouse]. 3670 mg/kg [Guinea pig].
DERMAL (LD50): Acute: 8400 mg/kg [Rabbit].
Triethylene glycol monobutyl ether:
A single eight hour exposure to rats at essentially saturated vapors resulted in no significant adverse
effects. (Clayton and Clayton, 1991). The compound is not expected to cause significant skin irritation
but may cause marked eye irritation with corneal injury. (Clayton and Clayton, 1991). In reproductive
and developmental animal studies, triethylene glycol monobutyl ether did not exhibit fetotoxicity,
teratogenic potential or maternal toxicity.
Diethylene glycol monobutyl ether:
The minimum lethal human exposure to diethylene glycol monobutyl ether has not been delineated.
One human case reported a dose of 2 mg/kg resulted in cyanosis, tachypnea, and slight uremia
(Brennaas, 1960). Rats consuming drinking water for 30 days containing 0.094 and 0.65 g/kg/day
developed reduction in appetite and histopathologic injury in either the kidney, liver, spleen, or testes
(Smyth & Carpenter, 1948). Animal data suggested a low hazard potential associated with a single
vapor inhalation exposure (Clayton & Clayton, 1991). However, in long term laboratory studies, certain
glycol ethers have been associated with fetal malformations in rats. Also, glycol ethers may cause
testicular atrophy leading to infertility. These effects may occur after repeated or prolonged exposure.
Diethylene glycol:
The major hazard from diethylene glycol occurs following the ingestion of relatively large single doses.
Diethylene glycol can cause central nervous system depression and hydropic degenerative lesions in
the liver and kidney. Anuria from tubular degeneration can prove fatal within a few days. In a 1937
case study, 105 fatalities occured among 353 people who ingested a solution of sulfanilamide in an
aqueous mixture containing 72% diethylene glycol. The symptoms included nausea, dizziness, and
pain in the kidney region. In a few days, oliguria and anuria, with death resulting from uremic poisoning.
(Amdur, Doull and Klaasen, 1991). Autopsies revealed that the principal signs of intoxication were in
the kidneys and liver (cortical necroses, nephrosis with severe vacuolization of the tubular epithelium,
liver congestion and fatty degeneration. (AIHA, 1999)
Reproductive toxicity was noted in a mouse continuous breeding study with large doses of diethylene
glycol in drinking water. In addition, health effects including liver and kidney disease were noted in
studies with pregnant rats receiving undiluted diethylene glycol. The relevance of these large dose
studies to human health is not certain.
Diethylene glycol monoethyl ether:
In laboratory studies, signs of toxicity from ingestion included ataxia followed by central nervous system
depression, prostration, coma and death. The kidneys appeared to be the organs most affected.
Microscopically, there was evidence of lung and heart inflammation, focal necrosis of the liver and
vacuolation of the cortical kidney tubules with occasional tubular casts. The maximum reported no
observable effect level (NOEL) was 0.49 g/kg. (AIHA, 1991).
Eye toxicity: 2-hr. Draize score 5.3/110
24-hr. Draize score 7.0/110
Pathological examination revealed no signs of toxic effects to rats after exposure to a saturated vapor
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 5
Continued on Next Page
Mystik?DOT 3 Brake Fluid
concentration for six hours. (AIHA, 1991)
Diethylene glycol monoethyl ether showed very weak mutagenic activity in some but not all strains of
Salmonella typhimurium, both with and without metabolic activation. It was weakly mutagenic in
Saccharomyces cerevisiae. In vivo, it showed no mutagenic activity measured in the mouse
micronucleus test (AIHA, 1991).
In a 2-year, three generation study of rats, kidney damage and changes in the liver, spleen and
intestine were reported at 0.95 g/kg/day.
Triethylene glycol monoethyl ether:
In an irritation bioassay, approximately 0.03 mL undiluted triethylene glycol monoethyl ether was
applied to human skin with a semioccluded patch for 24 hours on three consecutive days (Industrial
Bio-Test Laboratories,1969). Mild erythema was the only effect reported.
SECTION 12: ECOLOGICAL INFORMATION
Ecotoxicity Diethylene glycol:
LC50 Fathead Minnows, >100 ppm/96 hrs. (Static Test Environment)
LC50 Daphnia Magna, 0.3 - 1 ppm/96 hrs. (Static Test Environment)
No Effect Level, Selenastrum Capricornutum, 100 ppm (Static Test Environment)
This product is miscible in water and is expected to disperse in marine environments. The component
Environmental Fate
diethylene glycol will biodegrade in warmer water, with a half-life of at least ten days. In laboratory
studies, however, little degradation of diethylene glycol occured after 14 days with water temperatures
of 8?C (46?F).
SECTION 13: DISPOSAL CONSIDERATIONS
Hazard characteristic and regulatory waste stream classification can change with product use. Accordingly, it is the responsibility
of the user to determine the proper storage, transportation, treatment and/or disposal methodologies for spent materials and
residues at the time of disposition.
Conditions of use may cause this material to become a "hazardous waste", as defined by federal or
state regulations. It is the responsibility of the user to determine if the material is a "hazardous waste"
at the time of disposal. Transportation, treatment, storage, and disposal of waste material must be
conducted in accordance with RCRA regulations (see 40 CFR 260 through 40 CFR 271). State and/or
local regulations may be more restrictive. Contact the RCRA/Superfund Hotline at (800) 424-9346 or
your regional US EPA office for guidance concerning case specfic disposal issues. Empty drums and
pails retain residue. DO NOT pressurize, cut, weld, braze, solder, drill, grind, or expose this product's
empty container to heat, flame, or other ignition sources. DO NOT attempt to clean it. Empty drums
and pails should be drained completely, properly bunged or sealed, and promptly sent to a
reconditioner.
SECTION 14: TRANSPORT INFORMATION
Not a U.S. Department of Transportation regulated material.
DOT Status
Hydraulic Fluids other than Petroleum
Proper Shipping Name
Not a DOT controlled material (United States).
Hazard Class Not applicable.
Packing Group(s)
Not applicable.
UN/NA ID
Reportable Quantity A Reportable Quantity (RQ) has not been established for any components of this material.
Not applicable.
Emergency Response Guide
Placards No.
Not applicable.
HAZMAT STCC No.
Not a DOT "Marine Pollutant"
MARPOL III Status
per 49 CFR 171.8.
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 6
Continued on Next Page
Mystik?DOT 3 Brake Fluid
SECTION 15: REGULATORY INFORMATION
This product and/or its components are listed on the Toxic Substance Control Act (TSCA) inventory.
TSCA Inventory
The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires facilities subject
SARA 302/304
to Subparts 302 and 304 to submit emergency planning and notification information based on Threshold
Planning Quantities (TPQs) and Reportable Quantities (RQs) for "Extremely Hazardous Substances"
listed in 40 CFR 302.4 and 40 CFR 355. No components were identified.
The Superfund Amendments and Reauthorization Act of 1989 (SARA) Title III requires facilities subject
SARA 311/312
to this subpart to submit aggregate information on chemicals by "Hazard Category" as defined in 40
CFR 370.2. This material would be classified under the following hazard categories:
Acute (Immediate) Health Hazard,
This product contains the following components in concentrations above de minimis levels that are
SARA 313
listed as toxic chemicals in 40 CFR Part 372 pursuant to the requirements of Section 313 of SARA:
Triethylene glycol monobutyl ether, CAS Number, 143-22-6 Concentration: 45 - 55%
Diethylene glycol monobutyl ether, CAS Number, 112-34-5 Concentration: 20 - 50%
Diethylene glycol monopropyl ether, CAS Number, 6881-94-3 Concentration: 1 - 5%
Diethylene glycol monoethyl ether, CAS Number, 111-90-0 Concentration: 1 - 5%
Triethylene glycol monoethyl ether, CAS Number, 112-50-5 Concentration: 1 - 5%
The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA)
CERCLA
requires notification of the National Response Center concerning release of quantities of "hazardous
substances" equal to or greater than the reportable quantities (RQ's) listed in 40 CFR 302.4. As defined
by CERCLA, the term "hazardous substance" does not include petroleum, including crude oil or any
fraction thereof which is not otherwise specifically designated in 40 CFR 302.4. This product or refinery
stream is not known to contain chemical substances subject to this statute. However, it is
recommended that you contact state and local authorities to determine if there are any other reporting
requirements in the event of a spill.
This material is subject to the Clean Water Act (CWA). Discharges or spills on or into waters of the
CWA
United States, their adjoining shorelines, or into conduits leading to surface waters must be reported to
the EPA's National Response Center at (800) 424-8802.
This product is not known to contain the any components for which the State of California has found to
California
Proposition 65 cause cancer, birth defects or other reproductive harm.
For New Jersey labeling refer to components listed in Section 2.
New Jersey
Right-to-Know Label
No additional regulatory remarks.
Additional Regulatory
Remarks
SECTION 16: OTHER INFORMATION
Refer to the top of Page 1 for the HMIS and NFPA Hazard Ratings for this product.
REVISION INFORMATION
1.0
Version Number
07/14/1999
Revision Date
Printed on 05/03/2000.
Print Date
ABBREVIATIONS
AP = Approximately EQ = Equal GT = Greater Than LT = Less Than NA = Not Applicable ND = No Data NE = Not
Established
ACGIH = American Conference of Governmental Industrial Hygienists AIHA = American Industrial Hygiene Association
IARC = International Agency for Research on Cancer NTP = National Toxicology Program
NIOSH = National Institute of Occupational Safety and Health OSHA = Occupational Safety and Health Administration
NPCA = National Paint and Coating Manufacturers Association HMIS = Hazardous Materials Information System
NFPA = National Fire Protection Association EPA = Environmental Protection Agency
MSDS No. Revision Date 07/14/1999
663603002 Page Number: 7
Continued on Next Page
Mystik?DOT 3 Brake Fluid
DISCLAIMER OF LIABILITY
THE INFORMATION IN THIS MSDS WAS OBTAINED FROM SOURCES WHICH WE BELIEVE ARE RELIABLE. HOWEVER, THE
INFORMATION IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED OR IMPLIED REGARDING ITS CORRECTNESS. SOME
INFORMATION PRESENTED AND CONCLUSIONS DRAWN HEREIN ARE FROM SOURCES OTHER THAN DIRECT TEST DATA ON THE
SUBSTANCE ITSELF. THIS MSDS WAS PREPARED AND IS TO BE USED ONLY FOR THIS PRODUCT. IF THE PRODUCT IS USED AS
A COMPONENT IN ANOTHER PRODUCT, THIS MSDS INFORMATION MAY NOT BE APPLICABLE. USERS SHOULD MAKE THEIR
OWN INVESTIGATIONS TO DETERMINE THE SUITABILITY OF THE INFORMATION OR PRODUCTS FOR THEIR PARTICULAR
PURPOSE.
THE CONDITIONS OR METHODS OF HANDLING, STORAGE, USE, AND DISPOSAL OF THE PRODUCT ARE BEYOND OUR CONTROL
AND MAY BE BEYOND OUR KNOWLEDGE. FOR THIS AND OTHER REASONS, WE DO NOT ASSUME RESPONSIBILITY AND
EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE OR EXPENSE ARISING OUT OF OR IN ANY WAY CONNECTED WITH
HANDLING, STORAGE, USE OR DISPOSAL OF THE PRODUCT.
***** END OF MSDS *****
|