Product name: MF-2 page1 of 1
Material Safety Data Sheet
Section 1 - Product Identification
Product Name: MF-2 Formula type: Mixture
Manufacturer's Information:
Mass Finishing Inc. Emergency Telephone: 1-888-260-6277
1060 Commerce Blvd Information: 320-543-3222
Howard Lake, MN 55349 Fax: 320-543-3355
Section 2 - Hazardous Ingredients
INGREDIENTS CAS # % range TLV PEL
Stearic Acid 57-11-4 1-2 NA NA
3
10 mg/m3
Sodium Soap mixture NA 1-2 15 mg/m
10 mg/m3 5 mg/m3
Aluminum oxide 1344-28-1 3-4
Balance of ingredients are not defined as hazardous by OSHA
Comments TWA ?Time Weighted Average is the employee's average airborne exposure in any 8-hour work shift of a 40-hour work
week which shall not be exceeded. STEL ?Short Term Exposure Limit is the employee's 15-minute time weighted average
exposure which shall not be exceeded at any time during a work day unless another time limit is specified.
Section 3 - Physical Data
Form: Granulated Solid pH: None
Color: Yellow pH (1% vol): None
Odor: Mild Solubility in Water: No
Specific Gravity (Water = 1): <1 Vapor Density (Air = 1): ND
Boiling Point 癋: N/A % VOC by weight: ND
Evaporation Rate (Water = 1): N/A Vapor pressure: ND
Section 4 - Fire and Explosion Information
Flash Point (Method) F: >340 (COC)
Unusual Fire & Explosion No specific fire or explosion hazard. Smoke, fumes, hazardous decomposition products. Product is
Hazards: combustible (similar to sawdust)
Extinguishing Agents: Foam, carbon dioxide, dry chemical, water fog, water
Fire fighting methods: Evacuate area and fight fire from a safe distance. Fire fighters must wear MSHA/NIOSH approved
positive pressure breathing apparatus with full face mask and full protective equipment.
Section 5 - Health Hazard Data - Signs and Symptoms of Overexposure
Probable Routes of Entry: Eyes, skin, inhalation. Eye and skin irritant. See section 11: other effects for toxicity information.
Eyes: Contact with eyes may cause minor irritation such as redness, tearing.
Skin: This product contains materials that can cause slight skin irritation.
Inhalation: Overexposure may cause throat, lung and nose irritation.
Ingestion: Ingestion this product may cause nausea, vomiting and abdominal pain.
Medical Conditions Pre-existing disorders may be aggravated.
Aggravated by Exposure:
Section 6 - Emergency First Aid Procedures
Eyes: Check for and remove contact lenses. Flush immediately with copious amounts of water for 15 minutes while holding
eyelids apart to ensure complete irrigation of eye and eyelid tissues. If irritation develops, take exposed individual
immediately to a health care professional, preferably an ophthalmologist, for emergency first aid and further evaluation.
Skin: Wash exposed area with copious amounts of water. Repeat washing. If redness or irritation occurs, seek immediate
medical attention. Launder contaminated clothing before reuse.
Inhalation: If exposure by inhalation is suspected, move exposed individual to fresh air. If individual experiences nausea, headache,
dizziness, has difficulty breathing, seek a health care professional immediately. Administer CPR if necessary.
Product name: MF-2 page2 of 2
Ingestion: Do not induce vomiting unless directed by a physician. Obtain immediate medical aid or call poison control. During
vomiting there is a danger of aspirating liquid into lungs, causing serious damage and chemical pneumonitis. If
spontaneous vomiting occurs, keep head below hips to prevent aspiration and monitor for breathing difficulty. Seek
immediate medical attention or call 911. Never give anything by mouth to an unconscious person.
Section 7 - Reactivity Data
Stability: Stable when stored and used under normal conditions.
Incompatibility: Strong oxidizers, bases, reducing agents, and acids.
Hazardous Decomposition Thermal decomposition may release smoke, carbon dioxide, carbon monoxide, or other hazardous
Products: gases.
Hazardous Polymerization: Will not occur.
Section 8 - Spill & Leak Procedures
Procedures for Cleanup: Wear protective gear.
Small spills: Sweep up and rinse with water.
Large Spills: Ventilate area. Remove sources of ignition. Keep out of surface waters. Salvage for reuse if possible.
Otherwise place into suitable container for disposal. Do not flush to sewers. Inform local pollution
officials of spill. Call local regulatory agency.
Waste Disposal: Contact the proper county, state or federal authorities.
Section 9 - Special Protection Information
Ventilation Type Required: General or local
Protective Gloves: Wear rubber, neoprene, or nitrile gloves
Respiratory Protection: Not necessary under normal use conditions and ventilation. If dust is generated, wear NIOSH
respirator for mists.
Eye Protection: Wear safety glasses.
Other Equipment: Water source for eye and skin wash. Rubber boots to keep feet dry in case of spill.
Section 10 - Special Precautions
Product should be stored in cool dry area. Store out of direct sunlight. Keep out of reach of children. Keep container closed when not in
use. Thoroughly rinse empty containers before disposal. Use in well ventilated area. Do not breathe dust. Wash hands after handling.
Section 11 - Toxicity Data
Toxicity LD50 ?Oral - rat LD50 ?skin absorption-rabbit LC50 - Inhalation
Stearic Acid >10 g/kg ND ND
Sodium Soap mixture ND ND ND
Aluminum oxide ND ND ND
Carcinogenicity NTP IARC OSHA
Stearic Acid No No No
Sodium Soap mixture No No No
Aluminum oxide No Yes No
Other effects: Reproductive Toxicity Teratogenicity Mutagenicity
Stearic Acid No No No
Sodium Soap mixture No No No
Aluminum oxide No No No
Section 12 - Ecological Information
Environmental toxicity & Fate: This product is not known to be hazardous and expected to readily biodegradable.
Product name: MF-2 page3 of 3
Section 13 - Hazard Rating - HMIS
0 = minimal 1 = slight 2 = moderate 3 = serious 4 = severe
Health: 1 Reactivity: 0 Fire: 0 Personal protection equipment: B (gloves & glasses)
Section 14 - Regulatory Information
?Chemical Inventory Status - part 1 ?br>
Ingredient TSCA EC Japan Australia
Stearic Acid Yes Yes Yes Yes
Sodium Soap mixture Yes ND ND ND
Aluminum oxide Yes Yes Yes Yes
Ingredient Korea DSL NDSL Philippines
Corn Cob No No No No
Stearic Acid Yes Yes No Yes
Sodium Soap mixture ND Yes No ND
Aluminum oxide Yes Yes No Yes
?Federal, State & International Regulations ?part 1 ?br>
---- SARA 302 ---- -------------- SARA 313 ----------
Ingredient RQ TPQ List Chemical Catg.
Stearic Acid No No No No
Sodium Soap mixture No No No No
Aluminum oxide No No Yes No
Ingredient CERCLA RCRA 261.33 TSCA 8(d)
Stearic Acid No No No
Sodium Soap mixture No No No
Aluminum oxide No No No
TSCA 12(b): CDTA:
Chemical weapon No No No
SARA 311/312: Acute: yes Chronic: No Fire: Pressure:
No No
Reactivity: No
Section 15 - Shipping Name
Not DOT regulated
Section 16 - WHMIS
This material is classified as not hazardous under the WHMIS in Canada. This MSDS has been prepared according to the hazard criteria
of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.
Section 17 - Documentary Information
Date issued: 6/3/2008 Supersedes: Reason for update:
Prepared by: S. VanGrasstek Title: Phone: 763-417-1380
ABBREVIATIONS: NE = NOT ESTABLISHED NDA = NO DATA AVAILABLE
> = GREATER THAN <= LESS THAN BCF = BIOCONCENTRATION FACTOR
NA = NOT APPLICABLE ND = NO DATA
The data and recommendations presented herein are based upon our research and the research of others, and are believed to be accurate. However, no
warranty of guarantee of their accuracy is made; and the products are distributed without any warranty, expressed or implied, including the limited warranties
of merchantability of fitness for a particular purpose. The supplier makes no warranties, expressed or implied to the vendee, the vendee's employees or
anyone for any direct, special or consequential damages arising out of or in connection with the accuracy, adequacy or furnishing of such information.
Employers should use this information only as a supplement to other information and must make independent determinations of suitability to assure proper
use, safety, and health of employees.
|