Material Safety Data
Sheet
SECTION I: Product and Company Identity:
TRADE NAME (AS LABELED): TS-125 Die Lubricant
MANUFACTURER'S NAME: T.S. Moly-Lubricants, Inc.
MANUFACTURER'S ADDRESS: 6205 Brookhill #6
Houston TX 77087
EMERGENCY PHONE: 713/671-2676 Fax: 713/671-9417
BUSINESS PHONE: 713/671-2676 Fax: 713/671-9417
REVIEWED: July 26, 2005
REVIEWED BY: Jo Nell Salling
SECTION II: Composition /Information on Ingredients
The criteria for listing components in the composition section are as follows: Carcinogens are
listed when present at 0.1% or greater; components which are otherwise hazardous according to
OSHA are listed when present at 1.0% or greater; nonhazardous components are not listed as
being proprietary information. Refer to Section IX for regulatory information.
OSHA PEL (mg/m3)
Ingredient SARA CAS No. ACGIH TLV % Optional
(mg/m3)
Lead yes 19010-66-3 0.5 STEL: 0.5 1.0%
Dialkydithiocarbamate
Glycerine, no 56-81-5 NDA TWA:10 proprietary
1,2,3-Propanetriol
SECTION III: Hazards Identification
SYMPTOMS OF OVEREXPOSURE BY ROUTE HAZARDOUS MATERIAL
OF EXPOSURE: Overexposure to this product INFORMATION SYSTEM
may cause mild skin irritation, moderate eye
irritation, and possible gastric distress if ingested. HEALTH (BLUE) 2
MEDICAL CONDITIONS AGGRAVATED BY FLAMMABILITY (RED) 1
EXPOSURE: None known or reported. REACTIVITY (YELLOW) 0
CARCINOGENICITY: NTP? No IARC PROTECTIVE EQUIPMENT B
(WHITE)
Monographs? No OSHA regulated? No
In accordance with the current OSHA Hazard EYES RESPIRATORY HANDS BODY
Communication Standard criteria, this product is x x
not known or reported to be carcinogenic by
reference sources including: IARC, NTP, and
See Section 8
OSHA.
.
SECTION IV: First Aid Measures
MATERIAL SAFETY DATA SHEET
Page 2 of 3
TS-125 Die Lubricant
EYES: Flush eyes with plenty of water for several minutes. Get medical attention if eye
irritation persists.
SKIN: Remove any contaminated clothing and wash skin with plenty of soap and water for
several minutes. Get medical attention if skin irritation develops or persists. If product is
injected into or under the skin, or into any part of the body, regardless of the appearance of the
wound or its size, the individual should be evaluated immediately by a physician as a surgical
emergency. Even though initial symptoms from high pressure injection may be minimal or
absent, early surgical treatment within the first few hours may significantly reduce the ultimate
extent of injury.
INGESTION: If person is conscious and can swallow, give two glasses of water but do not
induce vomiting. If vomiting occurs, give fluids again. Consult a physician if symptoms
develop. DO NOT GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
INHALATION: If overcome from vapor, remove from exposure and call physician. If
necessary, provide respiratory support.
SECTION V: Fire Fighting Measures
Flash Point: >450 癋. Method: COC Flammable Limits: NDA
Extinguishing Media: Carbon dioxide, dry chemical, alcohol foam, water spray.
Special Fire Fighting Procedures: Use water to cool containers exposed to fire. For fires in
enclosed areas, firefighters should use self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: Avoid fumes of burning product.
SECTION VI: Accidental Release Measures
CLEAN WATER ACT/OIL POLLUTION ACT: This product may be classified as an oil under
Section 311 of the Clean Water Act, and under the Oil Pollution Act. Discharges or spills into or
leading to surface waters that cause a sheen must be reported to the National Response Center
(1/800-424-8802).
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Recover free
product. Add sand, earth, or some other suitable adsorbent. Keep product out of sewers and
watercourses by diking or impounding. Advise authorities if product has entered sewers, water
courses, or extensive land areas.
SECTION VII: Handling and Storage
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Store in cool dry area in
original or equivalent container in accordance with all applicable regulations. Do not apply high
heat or flame to container.
OTHER PRECAUTIONS: Good personal hygiene practices should always be followed.
SECTION VIII: Exposure Controls/Personal Protection
VENTILATION AND ENGINEERING CONTROLS: Use with adequate ventilation. Use a
mechanical fan or vent area to outside if necessary. Provide ventilation sufficient to prevent
exceeding recommended exposure limit or buildup of explosive concentrations of vapor in air.
RESPIRATORY PROTECTION: Respiratory protection is not expected to be needed. If
respiratory protection is needed, use only protection authorized by applicable regulations.
EYE PROTECTION: Safety goggles recommended.
HAND PROTECTION: Wear rubber gloves for routine industrial use.
MATERIAL SAFETY DATA SHEET
Page 3 of 3
TS-125 Die Lubricant
BODY PROTECTION: Use body protection as needed for task.
SECTION IX: Physical and Chemical Properties
Boiling Point: NDA Specific Gravity: 1.0
Vapor Pressure: NDA Evaporation Rate: Slower than ether
Vapor Density: Lighter than air Solubility in Water: Negligible
Appearance and Odor: Black, semi-solid with mild odor
SECTION X: Stability and Reactivity
STABILITY: Unstable: No Stable: Yes
CONDITIONS TO AVOID: Extreme heat
INCOMPATIBILITY: Strong oxidizers such as oxygen
POLYMERIZATION: May occur: No Will not occur: Yes
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: carbon monoxide, carbon dioxide,
fumes and smoke.
SECTION XI: Toxicological Information: No data available.
SECTION XII: Ecological Information: No data available.
SECTION XIII: Disposal Considerations
WASTE DISPOSAL METHODS: Dispose of waste according to all applicable regulations.
SECTION XIV: Transport Information
This material is not regulated as a DOT hazardous material.
SECTION XV: Regulatory Information
TOXIC SUBSTANCES CONTROL ACT (TSCA): All components are on the TSCA inventory
or are not required to be listed on the TSCA inventory.
SECTION XVI: Other Information
Disclaimer: Information given herein is offered in good faith as accurate, but without guarantee.
Conditions of use and suitability of this product for particular uses are beyond our control. Users
should make their own investigation to determine the suitability of the information or products
for their respective purposes.
|