Vicki Peters Nail Products MSDS#: KIG112900-EG2
GELSCULPT ?BUILDER GEL
Material Safety Data Sheet Page 1 of 5
Section 1 ?Identification of the Substance/Preparation and of the Company/Undertaking
MSDS Initial Approval Date: 11/29/2000
Product Name: EUROGEL?Builder Gel
MSDS Prepared by:vp BSQ
Chemical Name: N/A
TYPE 1
Family: UV GELS Manufacturer: Vicki Peters Nail Products
GEL Type:
2500 E. Imperial Hwy. Ste. 201 #371 Brea, CA 92821
Product Use: NAIL GEL Emergency Phone Numbers: ( 800 ) 535 - 5053
Product# 1000703 Information Contacts: (856) 663-4700
Section 2 - Composition/Information on Ingredients
Chemical Identity CAS Numbers EINECS# INCI Name Exposure Limits Carcinogen %
OSHA ACGIH
TWA/STEL TWA/STEL IARC/NTP/OSHA
Polyurethane Acrylate Exempt N/E Polyurethane N/E N/E Not Listed 90-95
Oligomer acrylate oligomer
Hydroxycyclohexyl 947-19-3 213-426-9 Hydroxycyclohexyl N/E N/E Not Listed 1-5
phenyl ketone phenyl ketone
Silicone Dioxide* 60676-86-0 262-373-8 Silica N/E N/E Not Listed 1-5
Benzophenone 119-61-9 204-337-6 Benzophenone N/E N/E Not Listed 0-1
D & C Violet #2 81-48-1 201-353-5 Violet 2/CI60725 N/E N/E Not Listed 0-1
D&C Red # 7 5281-04-9 226-109-5 CI15850 N/E N/E Not Listed 0-1
*- NIOSH Exposure limits for Silicone Dioxide= 6 mg/m3 TWA, 3000 mg/m3 IDLH
N/E - None Established N/DA - No Data Available
N/R - Not Reviewed N/A - Not Applicable
Hazard Symbols: Xi Risk Phrases: R20 Safety Phrases: S24/25, S28A, S37, S45
Section 3 - Hazards Identification
EMERGENCY OVERVIEW
This information is based on findings from related or similar materials.
May be slightly toxic.
?br>
May cause moderate skin injury (reddening & swelling).
?br>
May cause chemical burn in eye.
?br>
Potential Health Effects, Signs and Symptoms of Exposure:
Primary Route of Entry No specific information available.
Eye No specific information available. Contains materials that are essentially nonirritating, but contact
may cause slight transient irritation.
Skin No specific information available. Contains materials that may cause moderate skin injury (reddening
and swelling) and/or sensitization. Prolonged contact may cause blister formation (burns). Since
irritation may not occur immediately, contact can go unnoticed.
Ingestion No specific information available. Contains materials that may be practically nontoxic.
Inhalation No specific information available. Low volatility makes vapor inhalation unlikely. Aerosol can be
irritating.
Sub-Chronic Effects No specific information available. Limited tests showed no evidence of teratogenicity in animals. A
lifetime skin painting study with mice showed no evidence of carcinogenicity.
NOTE: Refer to Section 11, Toxicological Information for Details
Section 4 - First Aid Measures
First Aid for Eye Flush eyes with water for 15 minutes, including under eyelids. If irritation continues, seek medical
attention.
First Aid for Skin Remove contaminated clothing and wash contact area with soap and water for 15 minutes.
First Aid for Inhalation In case of exposure to a high concentration of vapor or mist, remove person to fresh air. If breathing
has stopped, administer artificial respiration and seek medical attention.
First Aid for Ingestion If appreciable quantities are swallowed, seek medical attention.
Revised Date: 03/22/06| Replaces Date: 11/08/2004
Vicki Peters Nail Products MSDS#: KIG112900-EG2
GELSCULPT ?BUILDER GEL
Material Safety Data Sheet Page 2 of 5
Section 5 - Fire Fighting Measures
Flash Point(癋/癈) Flammable Limit(vol%) Auto-ignition Temperature(vol%)
>212 癋/100 篊 Setaflash No Data No Data
Method:
Extinguishing Media: Use carbon dioxide or dry chemical for small fires; aqueous foam or water for large fires.
Fire Fighting Remove all ignition sources. Wear self-contained breathing apparatus and complete personal
Instructions: protective equipment when entering confined areas where potential for exposure to vapors or products
of combustion exists.
Unusual Hazards: High temperatures and fire conditions may cause rapid and uncontrolled polymerization which can
result in explosions and the violent rupture of storage vessels or containers. Avoid the use of a stream
of water to control fires since frothing can occur.
Section 6 - Accidental Release Measures
Spill or Release Spontaneous polymerization can occur. Although material is non-flammable please try to eliminate all ignition
Procedures - sources. Use eye and skin protection. Place leaking containers in a well ventilated area. Dike and recover large
spills. Soak up small spills with inert solids (such as vermiculite, clay) and sweep/shovel into disposal container.
Wash spill area with strong detregent and water solution; rinse with water, but minimize water use during clean-
up. Do not flush to sewer! US Regulations (CERCLA) require reporting spills and releases to soil, water and air
in excess of reportable quantities. The toll free number for the US Coast Guard National Response Center is (800)
424-8802. EU Regulations require the consultation of Directive 98/24/EC. Dispose and report per regulatory
requirements if necessary. Please prevent washings from entering waterways.
Section 7 - Handling and Storage
Handling Avoid contact with skin and eyes. Avoid breathing vapor. Keep container closed when not in use. Avoid
prolonged exposure to light. Remove all contaminated clothing, shoes, belts and other leather goods immediately.
Incinerate leather goods ( including shoes ). Wash contaminated clothing thoroughly before reuse. Wash skin
thoroughly with soap and water after handling. Solvents should not be used to clean skin because of increased
penetration potential.
When handling gel for product use, do not heat above 100篎/38篊 or disassociation of silica in product may occur.
Storage Store in a cool place, away from heat and light. Store at temperatures below 100癋/38篊.
Explosion High temperatures and fire conditions may cause rapid and uncontrolled polymerization which can result in
Hazard explosions and the violent rupture of storage vessels or containers.
Section 8 - Exposure Controls / Personal Protective Equipment
Engineering Controls Local exhaust recommended to control exposure which may result from operations generating aerosols and hot
operations generating vapors.
Personal Protective Equipment
General To identify additional Personal Protective Equipment (PPE) requirements, it is recommended
that a hazard assessment in accordance with the OSHA PPE Standard (29CFR1910.132), or
European Standard EN166 be conducted before using this product . Provide eye wash stations
and safety showers. Wear impervious clothing to prevent ANY contact with this product, such
as gloves, apron, boots, or whole body suit. Nitrile rubber is better than PVC.
Eye/ Face Protection Chemical splash goggles.
Skin Protection Impervious gloves (Neoprene).
Respiratory Protection A NIOSH/MSHA approved air purifying respirator with an organic vapor cartridge or canister may be
permissible under certain limited circumstances where airborne concentrations are expected to exceed
exposure limits. Protection provided by nuisance level organic vapor dust masks can be used, however
the use of these types of respirators are limited. Follow OSHA respirator regulations found in 29 CFR
1910.134 or European Standard EN 149.
Revised Date: 03/22/06| Replaces Date: 11/08/2004
Vicki Peters Nail Products MSDS#: KIG112900-EG2
GELSCULPT ?BUILDER GEL
Material Safety Data Sheet Page 3 of 5
Section 9 - Physical and Chemical Properties
Appearance Odor & Odor Threshold PH Specific Gravity Viscosity % Volatile
Light ,amber/pink mobile liquid characteristic acrylate odor NA (H2O=1) : 1.15 N/DA By Volume : < 0.5
Boiling Point/ Decomposition Octanol/Water Vapor Vapor Evaporation Ignition Solubility
Freezing Point Temperature Partitioning Coefficient Pressure: Density Rate In Water
Log Po/w (20癈)
Not applicable N/A N/A (mm Hg) @ 20 C : < No Data No Data No Data Insoluble
0.01
Flash Point(癋/癈) Flammable Limit(vol%) Auto-ignition Temperature(vol%)
>212 癋/100 篊 Setaflash No Data No Data
Section 10 - Stability and Reactivity
Stability Incompatibility (Materials to Avoid):
Normally Stable Polymerization initiators including peroxides, strong
oxidizing agents, copper, copper alloys, carbon steel, iron
Hazardous Decomposition Products:
,rust and string bases.
Fumes produced when heated to decomposition may include:
carbon monoxide, carbon dioxide. Hazardous Polymerization:
May occur -- Uncontrolled polymerization may cause
Conditions to Avoid: rapid evolution of heat and increased pressure that could
result in violent rupture of sealed storage vessels or
Storage > 100 ?F , exposure to light, loss of dissolved air, loss of
containers.
polymerization inhibitor, contamination with incompatible
materials.
Section 11 - Toxicological Information
Acute Oral Toxicity Acute Dermal Toxicity Acute Inhalation Toxicity Irritation - skin Irritation - Eye
No information available No information available No information available No information available No information
available
Since this product contains a very low concentration of active components, the primary toxicological information is derived from the oligomers.
Further hazardous properties cannot be excluded. The product should be handled with care when dealing with chemicals.
Sensitization Mutagenicity Sub-chronic Toxicity
N/DA N/DA N/DA
Section 12 - Ecological Information
Ecotoxicological Information
Acute Toxicity Acute Toxicity Acute Toxicity Bioconcentration Toxicity to Sewage Bacteria
to Fish to Invertebrates to Algae
N/DA N/DA N/DA N/DA N/DA
Chemical Fate Information
Biodegradability N/DA
Chemical Oxygen Demand N/DA
To the best of our knowledge, the ecotoxocological and chemical fate properties have not been thoroughly investigated.
Do not allow to enter drinking water supplies, wastewater, or soil
Section 13 - Disposable Considerations
Non-contaminated, properly inhibited product is not a RCRA hazardous waste. It is the genrators responsibility to determine what
is classified as a hazardous waste. Comply with all federal, state, and local regulations.
Dispose of diking materials and absorbent in compliance with State, Local, and Federal regulations. Residual vapors may explode
on ignition; do not cut, drill, or weld on or near the container. Mix with compatible chemical which is less flammable and
incinerate.
Section 14 - Transport Information
Revised Date: 03/22/06| Replaces Date: 11/08/2004
Vicki Peters Nail Products MSDS#: KIG112900-EG2
GELSCULPT ?BUILDER GEL
Material Safety Data Sheet Page 4 of 5
DOT (49 CFR 172)
Proper Shipping Name: Non-Regulated Material
Identification Number: N/A
Marine Pollutant: No
Special Provisions: None
Emergency Response Guidebook (ERG) #: N/A
IATA (DGR):
Proper Shipping Name: Non-Regulated Material
Class or Division: N/A
UN or ID Number: N/A
Packaging Instructions: None
Emergency Response Guidance (ICAO)#: N/A
IMO (IMDG):
Proper Shipping Name: Non-Regulated Material
Class or Division: N/A
UN or ID Number: N/A
Special Provisions & Stowage/Segregation: None
Emergency Schedule (EmS)#: N/A
Other Information: Flash point >100篊
Section 15 - Regulatory Information
US Federal Regulations
Clean Air Act: HAP/ODS This product contains the following hazardous air pollutants (HAP's), as defined by the U.
S. Clean Air Act:
?Benzophenone, CAS# 119-61-9 (SOCMI)
This product does not contain any Class1 or Class 2 ODS.
Clean Water Act: Priority Pollutant This product contains no chemicals listed under the U. S. Clean Water Act Priority
Pollutant List.
FDA: Food Packaging Status This product has not been cleared by the FDA for use in food packaging and / or other
applications as an indirect food additive.
Occupational Safety and Health Act This product is considered to be a hazardous chemical under the OSHA Hazard
Communication Standard. Its hazards are :
?Immediate (acute) health hazard
?Delayed (chronic) health hazard
?Reactive hazard
RCRA This product is not considered to be a hazardous waste under RCRA (40 CFR 261).
SARA Title III: Section 302 (TPQ): This product contains no chemicals regulated under Sec. 302 as extremely hazardous
substances.
SARA Title III: Section 302 (RQ): This product contains no chemicals regulated under Section 304 as extremely hazardous
chemical for emergency release notification (" CERCLA" List).
SARA Title III: Section 311-312: This product is considered hazardous under the OSHA Hazard Communication Standard
and is regulated under Section 311-312 (40 CFR 370). Its hazards are:
?Immediate (acute) health hazard
?Delayed (chronic) health hazard
?Reactive hazard
SARA Title III: Section 313: This product contains no chemicals subject to the reporting requirements of Section 313
of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR
Part 372.
TSCA Section 8(b): Inventory: This product contains chemicals listed on the TSCA inventory or otherwise complies with
TSCA premanufacture notification requirements.
TSCA Significant New Use Rule: None of the chemicals listed have a SNUR under TSCA.
State Regulations
Revised Date: 03/22/06| Replaces Date: 11/08/2004
Vicki Peters Nail Products MSDS#: KIG112900-EG2
GELSCULPT ?BUILDER GEL
Material Safety Data Sheet Page 5 of 5
CA Right-to-Know Law: NONE
California No Significant Risk Rule: NONE
MA Right-to-Know Law: Silicone Dioxide, CAS#7631-86-9
NJ Right-to-Know Law: Silicone Dioxide, CAS#7631-86-9
PA Right-to-Know Law: Silicone Dioxide, CAS#7631-86-9
FL Right-to-Know Law: Silicone Dioxide, CAS#7631-86-9
MN Right-to-Know Law: Benzophenone, CAS #119-61-9, Silicone Dioxide, CAS#7631-86-9
International Regulations
CDSL: Canadian Inventory Silicone Dioxide, CAS#7631-86-9 is on the DSL list. WHMIS = n/da
(on Canadian Transitional List) Hydroxycyclohexyl phenyl ketone CAS #947-19-3 is on the DSL list. WHMIS = n/da
Benzophenone, CAS #119-61-9 is on the DSL list. WHMIS = n/da
EINECS: European Inventory: ?Hazard Symbol Xi: Irritant
?Risk Phrases: R20: Harmful by inhalation
?Safety Phrases: S24/25: Avoid contact with skin and eyes, S28A: After contact with
skin, wash immediately with plenty of water, S37: Wear suitable protective gloves,
S45: In case of accident, or if you feel unwell, seek medical advise immediately (show
the label where possible)
Section 16 - Other Information
Hazard Rating System (Pictograms)
NFPA: HMIS:
2
Flammability
1
1
2 1
Health Reactivity
1
Revised Sections since Last Version 11/08/04: Section Header Updates
Revised Sections since Last Version 03/22/06: Updated format and NFPA diamond update.
The information presented herein was obtained from sources considered to be reliable. However, this information is provided without any warranty,
expressed or implied, regarding its correctness or suitability for consumers intended use and/or application. For this and other reasons, we assume no
responsibility and expressly disclaim liability for loss, damage or expense arising out of any way connected with the handling, storage, use or
disposal of the product. This MSDS was prepared expressly for this product. Use the materials only as directed. If the product is used as a
component of another product, the information contained within the MSDS may not be applicable. If one could have any concerns with or problems
understanding this MSDS form, please direct all questions to INFOTRAC, Chemical Emergency Resources System at 1(800) 535-5053.
Revised Date: 03/22/06| Replaces Date: 11/08/2004
|