Material Safety Data Sheet
POLYSTAR, LLC
208 Brookhollow Industrial Blvd, Dalton, GA. 30720
IN CASE OF EMERGENCY CALL CHEMTREC 1-800-424-9300 CONTACT ONLY IN CASE OF
CHEMICAL EMERGENCIES INVOLVING A SPILL, LEAK, FIRE, EXPOSURE, OR ACCIDENT
INVOLVING CHEMICALS.
Product Name: ChemCure 365
Effective Date: 1/11/2008
1. INGREDIENTS:
(CAS# 2855-13-2) < 50%
Isophorone Diamine
(CAS# 100-51-6) < 50%
Benzyl Alcohol
1,3-Benzenedimethanamine (CAS# 1477-55-0) <50%
This document is prepared pursuant to the OSHA Hazard Communication Standard (29 CFR
1910.1200) in addition, other substances not Hazardous per this OSHA Standard may be listed.
Where proprietary Ingredient shows, the identity may be made available as provided in this
standard.
2. PHYSICAL DATA:
BOILING POINT: 401癋
VAP PRESSURE: 0.02mmHG @20?68? C, F
VAP DENSITY: 5.88
SOL. IN WATER: Moderately soluble.
SP. GRAVITY: 1.04
APPEARANCE: Pale straw colored liquid
ODOR: Amine odor
3. FIRE AND EXPLOSION HAZARD DATA:
FLASH POINT: 213? F
METHOD USED: PMCC
FLAMMABLE LIMITS:
LFL: Not Determined
UFL: Not Determined
EXTINGUISHING MEDIA: Water fog, alcohol foam, CO2, dry chemical.
FIRE & EXPLOSION HAZARDS: Use full protective clothing
FIRE-FIGHTING EQUIPMENT: Use a positive pressure, self-contained breathing apparatus.
4. REACTIVITY DATA:
STABILITY: (CONDITIONS TO AVOID) Can react strongly with epoxy resins at elevated
temperatures.
INCOMPATIBILITY: (SPECIFIC MATERIALS TO AVOID) Epoxy resins under uncontrolled
conditions.
HAZARDOUS DECOMPOSITION PRODUCTS: Nitrogen oxides when burned.
HAZARDOUS POLYMERIZATION: Will not occur.
5. ENVIRONMENTAL AND DISPOSAL INFORMATION:
ACTION TO TAKE FOR SPILLS/LEAKS: Large spill -- dike up and pump into appropriate
containers. Small spill -- use noncombustible absorbent material/sand and shovel into suitable
containers.
DISPOSAL METHOD: Large quantities should be recovered. Collect small quantities in waste
metal drums and seal for removal to an approved landfill, or incinerate in accordance with local,
state, and federal regulations.
6. HEALTH HAZARD DATA:
EYE: May cause severe irritation with corneal injury, which may result in permanent impairment
of vision, even blindness. Vapors may irritate eyes.
SKIN CONTACT: May cause severe injury to skin following prolonged or repeated contact, and
may cause skin sensitization or other allergic responses.
SKIN ABSORPTION: A single prolonged exposure may result in the material being absorbed in
harmful amounts. The LD50 for skin absorption has not been determined.
INGESTION: Single dose oral toxicity is low. The oral LD50 has not been determined. Ingestion
may cause gastrointestinal irritation or ulceration. Ingestion may cause burns of mouth and throat.
INHALATION: May cause respiratory sensitization or asthma in susceptible individuals.
Excessive exposure may cause irritation to upper respiratory tract.
SYSTEMIC & OTHER EFFECTS: Results of in vitro ("test tube") mutagenicity tests have been
negative.
7. FIRST AID:
EYES: Immediate and continuous irrigation with flowing water for at least 30 minutes is required.
Promptly seek medical attention.
SKIN: Immediately flush skin with plenty of water for at least 15 minutes while removing
contaminated clothing, preferably under a safety shower. Seek medical attention immediately.
Avoid prolonged or repeated contact to skin. Wash thoroughly after handling.
INGESTION: Do not induce vomiting. Give large amounts of water or milk if available and
transport to medical facility.
INHALATION: Remove to fresh air if effects occur. Consult a physician.
NOTE TO PHYSICIAN: Corrosive. May cause stricture. If lavage is performed, suggest
endotracheal and/or esophagoscopic control. If burn is present, treat as any thermal burn, after
decontamination. No specific antidote. Supportive care. Treatment based on judgement of the
physician in response to reactions of the patient.
8. HANDLING PRECAUTIONS:
EXPOSURE GUIDELINE(S): None established.
VENTILATION: Control airborne concentration below the exposure guideline. Use only with
adequate ventilation. Local exhaust ventilation may be necessary for some operations.
RESPIRATORY PROTECTION: Atmospheric levels should be maintained below the exposure
guideline. When respiratory protection is required for certain operations, use an approved
airpurifying respirator.
SKIN PROTECTION: Use protective clothing impervious to this material. Selection of specific
items such as gloves, boots, apron, or full-body suit will depend on operation. Safety shower
should be located in immediate work area. Remove contaminated clothing immediately, wash
skin area with soap and water, and launder clothing before reuse. Contaminated leather items,
such as shoes, belts and watchbands, should be removed and destroyed.
EYE PROTECTION: Use chemical goggles. If vapor exposure causes eye irritation, use a fullface
respirator. Eye wash fountain should be located in immediate work area.
9. ADDITIONAL INFORMATION:
SPECIAL PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Ground all transfer
equipment. Hold bulk storage under a nitrogen blanket. This product should not come in contact
with copper or copper-bearing alloys. Good general housekeeping procedure should be followed.
10. NFPA HAZARD RATING:
HEALTH 2
4 = EXTREME
FIRE 1
3 = HIGH
REACTIVITY 0
2 = MODERATE
SPECIFIC -
1 = SLIGHT
0 = INSIGNIFICANT
11. REGULATORY INFORMATION:
STATUS ON SUBSTANCE LISTS:
The concentrations shown in this document are maximum or ceiling levels (expressed in weight
%, unless otherwise specified) to be used for regulations. Trade Secrets are indicated by "TS".
FEDERAL EPA:
COMPREHENSIVE ENVIRONMENTAL RESPONSE, COMPENSATION, and LIABILITY ACT of
1980 (CERCLA):
Requires notification of the National Response Center of release of quantities of Hazardous
Substances equal to or greater than the reportable quantities (RQ's) in 40 CFR 302.4.
Components present in this product at level which could require reporting under the statute are:
Chemical Name CAS Number % By Weight RQ
NONE
SUPERFUND AMENDMENTS and REAUTHORIZATION ACT of 1986 (SARA) TITLE III:
Sections 301-304 require emergency planning based on Threshold Planning Quantities (TPQs)
and release reporting based on Reportable Quantities (RQs) in 40 CFR 355. Components
present in this product at a level which could require reporting under this statute are:
Chemical Name CAS Number % By Weight
NONE
Sections 311-312 require products be reviewed and applicable EPA Hazard Definitions be
identified and made known.
EPA HAZARD CLASSIFICATIONS:
Acute Chronic Fire Pressure Reactive
Hazard Hazard Hazard Hazard Hazard
yes yes no no no
Section 313 requires submission of annual reports of release of toxic chemicals that appear in 40
CFR 372 (for SARA 313). This information must be included in all MSDSs that are copied and
distributed for this material. Components present in this product at level which could require
reporting under the statute are:
Chemical Name CAS Number % By Weight
NONE
If you are unsure if you must report more information, call the EPA Emergency Planning and
Right-To-Know Hot Line: 800-535-0202 or 202-479-2449.
TOXIC SUBSTANCES CONTROL ACT (TSCA):
The components of this product are contained on the chemical substance inventory list.
OTHER REGULATORY INFORMATION:
D.O.T.Shipping Name:
Corrosive Liquids, N.O.S. (Isophoronediamine), Class 8, UN 1760, PG III
The information and recommendations in this publication are accurate to the best of our
belief. User must conduct their own tests to determine the suitability of these products for
their particular purposes. Because of numerous factors affecting results, Polystar, LLC
MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR PURPOSE, other than the material conforms to
our applicable current specifications. Standard Specifications, although current at the
time of publication, are subject to change without notice. For latest Standard
Specifications contact our nearest sales office. Statements herein, therefore, are not
representation or warranties. Polystar's liability arising out of breach of warranty,
negligence, strict liability, or otherwise is limited to the purchase price of material. User
assumes responsibility if its actual application infringes others' intellectual property
rights.
|