MATERIAL SAFETY DATA SHEET 01
FILE NO.:
SaniGLAZE CONTAMINANT REMOVER 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
CONTAMINANT REMOVER
PRODUCT NAME:
None
SYNONYMS:
01-01-001
PRODUCT CODES:
Tile and grout cleaning and preparation
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 >50 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Ethanolamine 141-43-5 <7 No
ppm mg/m3
3 6
OSHA PEL-TWA:
NIOSH REL - TWA: 3 8
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Sodium Hydroxide 1310-73-2 <5 No
ppm mg/m3
OSHA PEL-TWA: --- 2
NIOSH REL - TWA: --- 5
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
ROUTES OF ENTRY:
Yes (mists)
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 01
FILE NO.:
SaniGLAZE CONTAMINANT REMOVER 10/15/03
MSDS DATE:
POTENTIAL HEALTH EFFECTS:
If sprayed or misted may cause chemical pneumonitis, irritation, or chemical burns.
Inhalation:
Irritating and corrosive. Prolonged contact may cause dermatitis, drying of skin or tissue
Skin:
damage.
Do not take internally. Corrosive and toxic if ingested. May cause burning, irritation of mouth
Ingestion:
and throat, nausea, gastrointestinal distress or diarrhea.
May cause eye irritation, chemical burns and possible permanent tissue damage or blindness.
Eyes:
Liquid is corrosive to tissue.
ACUTE HEALTH HAZARDS:
Liquid is corrosive to tissue.
CHRONIC HEALTH HAZARDS:
Contact or breathing mists may exacerbate existing skin or respiratory
AGGRAVATION OF PRE-EXISTING
disorders.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate
EYES:
all the areas around the eye and lid. Get medical attention as soon as first aid
has been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting. Drink 3-4 glasses of citrus juice or water, and call the
INGESTION:
nearest poison control center.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
FLAMMABLE LIMITS IN AIR,
None
UPPER:
LOWER: None
FLASH POINT: 癋: None
癈: None
None
METHOD USED:
AUTOIGNITION TEMPERATURE: 癋: None
癈: None
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 01
FILE NO.:
SaniGLAZE CONTAMINANT REMOVER 10/15/03
MSDS DATE:
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 0 REACTIVITY: 1 PROTECTION:
Not applicable
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Liquid, vapors and mists are corrosive. Wear self-contained
breathing apparatus and full protective gear for fires that involve
this material.
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, and other
HAZARDOUS DECOMPOSITION PRODUCTS:
unidentified fragments if this product is involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread
of liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of
in accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain
residue. All containers should be disposed of in an environmentally safe
manner, and in accordance with all governmental regulations. Keep this and all
chemicals out of the reach of children.
OTHER PRECAUTIONS: None
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 01
FILE NO.:
SaniGLAZE CONTAMINANT REMOVER 10/15/03
MSDS DATE:
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed.
Safety glasses (ANSI Z87.1) or approved equivalent as necessary to minimize eye
EYE PROTECTION:
contact hazards.
Neoprene or other materials may be used if there is documented evidence of
SKIN PROTECTION:
compatibility.
Neoprene aprons, overshoes, oversleeves or other impervious clothing
OTHER PROTECTIVE CLOTHING
as necessary to minimize exposure.
OR EQUIPMENT:
Use proper industrial hygiene practices to minimize hazardous exposure.
WORK HYGIENIC PRACTICES:
Wash hands after handling this material, and before eating or smoking.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Clear, light amber liquid
APPEARANCE:
Mild "soap" odor
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
>212 癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
Same as water.
VAPOR PRESSURE (mmHg):
Same as water
VAPOR DENSITY (AIR = 1):
1.09
SPECIFIC GRAVITY (H2O = 1):
>1
EVAPORATION RATE(H2O = 1):
Water miscible
SOLUBILITY IN WATER:
PERCENT SOLIDS BY WEIGHT:
PERCENT VOLATILE (BY WT):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
None
CONDITIONS TO AVOID (STABILITY):
Strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 01
FILE NO.:
SaniGLAZE CONTAMINANT REMOVER 10/15/03
MSDS DATE:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
Not available
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
ECOLOGICAL
Not available
INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved
WASTE DISPOSAL METHOD:
landfill in accordance with governmental regulations. If these options are not
available, consign the recovered material to a licensed hazardous waste
contractor.
Corrosive (concentrated, undiluted form)
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
Corrosive liquid, Basic, Inorganic, N.O.S. (Contains Sodium Hydroxide and
PROPER SHIPPING NAME:
ethanolamine), 8, PG III
HAZARD CLASS: 8
ID NUMBER: UN 3266
PACKING GROUP: III
LABEL STATEMENT: Corrosive
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 01
FILE NO.:
SaniGLAZE CONTAMINANT REMOVER 10/15/03
MSDS DATE:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness
or accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 02
FILE NO.:
SaniGLAZE GEL CONTAMINANT REMOVER 3/6/07
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
GEL CONTAMINANT REMOVER
PRODUCT NAME:
None
SYNONYMS:
01-02-001/GEL
PRODUCT CODES:
Wall, baseboard and tile surface cleaning and preparation
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
115 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
none
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 >90 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Sodium Hydroxide 1310-73-2 <5 No
ppm mg/m3
OSHA PEL-TWA: --- 2
NIOSH REL - TWA: --- 5
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Ethanolamine 141-43-5 <1
ppm mg/m3
6
OSHA PEL-TWA:
NIOSH REL - TWA: 6
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes (mists)
Inhalation:
Yes
Skin:
Yes
Ingestion:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 02
FILE NO.:
SaniGLAZE GEL CONTAMINANT REMOVER 3/6/07
MSDS DATE:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
If sprayed or misted may cause chemical pneumonitis, irritation, or chemical burns.
Inhalation:
Irritating and corrosive. Prolonged contact may cause dermatitis, drying of skin or tissue
Skin:
damage.
Do not take internally. Corrosive and toxic if ingested. May cause burning, irritation of mouth
Ingestion:
and throat, nausea, gastrointestinal distress or diarrhea.
May cause eye irritation, chemical burns and possible permanent tissue damage or blindness.
Eyes:
Liquid is corrosive to tissue.
ACUTE HEALTH HAZARDS:
Liquid is corrosive to tissue.
CHRONIC HEALTH HAZARDS:
Contact or breathing mists may exacerbate existing skin or respiratory
AGGRAVATION OF PRE-EXISTING
disorders.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate
EYES:
all the areas around the eye and lid. Get medical attention as soon as first aid
has been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting. Drink 3-4 glasses of citrus juice or water, and call the
INGESTION:
nearest poison control center.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
None
FLAMMABLE LIMITS IN AIR, UPPER:
None
LOWER:
FLASH POINT: 癋: None
None
METHOD USED:
AUTOIGNITION TEMPERATURE: 癋: None
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 02
FILE NO.:
SaniGLAZE GEL CONTAMINANT REMOVER 3/6/07
MSDS DATE:
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 0 REACTIVITY: 1 PROTECTION:
Not applicable
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Liquid, vapors and mists are corrosive. Wear self-contained
breathing apparatus and full protective gear for fires that involve
this material.
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, and other
HAZARDOUS DECOMPOSITION PRODUCTS:
unidentified fragments if this product is involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread
of liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of
in accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain
residue. All containers should be disposed of in an environmentally safe
manner, and in accordance with all governmental regulations. Keep this and all
chemicals out of the reach of children.
OTHER PRECAUTIONS: None
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 02
FILE NO.:
SaniGLAZE GEL CONTAMINANT REMOVER 3/6/07
MSDS DATE:
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed.
Safety glasses (ANSI Z87.1) or approved equivalent as necessary to minimize eye
EYE PROTECTION:
contact hazards.
Neoprene or other materials may be used if there is documented evidence of
SKIN PROTECTION:
compatibility.
Neoprene aprons, overshoes, oversleeves or other impervious clothing
OTHER PROTECTIVE CLOTHING
as necessary to minimize exposure.
OR EQUIPMENT:
Use proper industrial hygiene practices to minimize hazardous exposure.
WORK HYGIENIC PRACTICES:
Wash hands after handling this material, and before eating or smoking.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Clear, light amber liquid
APPEARANCE:
Mild "soap" odor
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
>212 癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
Same as water
VAPOR PRESSURE (mmHg):
Same as water
VAPOR DENSITY (AIR = 1):
1.09
SPECIFIC GRAVITY (H2O = 1):
>1
EVAPORATION RATE(H2O = 1):
Water miscible
SOLUBILITY IN WATER:
PERCENT SOLIDS BY WEIGHT:
PERCENT VOLATILE (BY WT):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
None
CONDITIONS TO AVOID (STABILITY):
Strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is
involved in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 02
FILE NO.:
SaniGLAZE GEL CONTAMINANT REMOVER 3/6/07
MSDS DATE:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved
WASTE DISPOSAL METHOD:
landfill in accordance with governmental regulations. If these options are not
available, consign the recovered material to a licensed hazardous waste
contractor.
Corrosive (concentrated, undiluted form)
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
Corrosive liquid, Basic, Inorganic, NOS (Contains Sodium Hydroxide and
PROPER SHIPPING NAME:
ethanolamine), 8, UN3266, PG III
HAZARD CLASS: 8
ID NUMBER: UN3266
PACKING GROUP: III
LABEL STATEMENT: Corrosive
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 02
FILE NO.:
SaniGLAZE GEL CONTAMINANT REMOVER 3/6/07
MSDS DATE:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness
or accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 03
FILE NO.:
SaniGLAZE TILE AND GROUT PREP 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
TILE AND GROUT PREP
PRODUCT NAME:
None
SYNONYMS:
01-01-002
PRODUCT CODES:
Tile surface cleaning and preparation
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
none
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Hydrochloric Acid 7647-01-0 >26
ppm mg/m3
OSHA PEL-TWA: 5 7
NIOSH REL - TWA: 5 7
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Sulfamic Acid 5329-14-6 <9 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Hydroxyacetic Acid 79-14-1 <6 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes (mists)
Inhalation:
Yes
Skin:
Yes
Ingestion:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 03
FILE NO.:
SaniGLAZE TILE AND GROUT PREP 10/15/03
MSDS DATE:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
Breathing mists or vapors may irritate the throat and lungs.
Inhalation:
Irritating. Prolonged contact may result in chemical burns.
Skin:
Do not take internally. May cause burning, irritation of mouth and throat, nausea,
Ingestion:
gastrointestinal distress or diarrhea.
May cause eye irritation, mild to severe chemical burns and possible permanent tissue damage
Eyes:
or blindness.
Liquid is corrosive to tissue.
ACUTE HEALTH HAZARDS:
Liquid is corrosive to tissue.
CHRONIC HEALTH HAZARDS:
Contact or breathing mists may exacerbate existing skin or respiratory
AGGRAVATION OF PRE-EXISTING
disorders.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate
EYES:
all the areas around the eye and lid. Get medical attention as soon as first aid
has been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting. Drink 3-4 glasses of milk or water, and call the nearest
INGESTION:
poison control center.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
FLAMMABLE LIMITS IN AIR, UPPER: None
LOWER: None
FLASH POINT: 癋: None
None
METHOD USED:
AUTOIGNITION TEMPERATURE: 癋: None
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 03
FILE NO.:
SaniGLAZE TILE AND GROUT PREP 10/15/03
MSDS DATE:
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 0 REACTIVITY: 1 PROTECTION:
Not applicable
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Liquid, vapors and mists are corrosive. Wear self-contained
breathing apparatus and full protective gear for fires that involve
this material.
This product can react with metals and release hazardous
UNUSUAL FIRE AND EXPLOSION HAZARDS:
quantities of hydrogen gas.
May evolve hydrogen gas or sulfur dioxide (SO2) if this
HAZARDOUS DECOMPOSITION PRODUCTS:
product is involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread
of liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of
in accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain
residue. All containers should be disposed of in an environmentally safe
manner, and in accordance with all governmental regulations. Keep this and all
chemicals out of the reach of children.
OTHER PRECAUTIONS: None
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 03
FILE NO.:
SaniGLAZE TILE AND GROUT PREP 10/15/03
MSDS DATE:
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed.
Safety glasses (ANSI Z87.1) or approved equivalent as necessary to minimize eye
EYE PROTECTION:
contact hazards.
Neoprene or other materials may be used if there is documented evidence of
SKIN PROTECTION:
compatibility.
Neoprene aprons, overshoes, oversleeves or other impervious clothing as
OTHER PROTECTIVE CLOTHING
necessary to minimize exposure.
OR EQUIPMENT:
Use proper industrial hygiene practices to minimize hazardous exposure.
WORK HYGIENIC PRACTICES:
Wash hands after handling this material, and before eating or smoking.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Clear, amber liquid
APPEARANCE:
Slight astringent odor
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
>212 癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
Same as water
VAPOR PRESSURE (mmHg):
Same as water
VAPOR DENSITY (AIR = 1):
1.10
SPECIFIC GRAVITY (H2O = 1):
>1
EVAPORATION RATE(H2O = 1):
Water miscible
SOLUBILITY IN WATER:
PERCENT SOLIDS BY WEIGHT:
PERCENT VOLATILE (BY WT):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
None
CONDITIONS TO AVOID (STABILITY):
Metal containers, strong oxidizers, strong alkalis
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 03
FILE NO.:
SaniGLAZE TILE AND GROUT PREP 10/15/03
MSDS DATE:
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved
WASTE DISPOSAL METHOD:
landfill in accordance with governmental regulations. If these options are not
available, consign the recovered material to a licensed hazardous waste
contractor.
Corrosive (concentrated, undiluted form)
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
Corrosive liquid, Acidic, Inorganic, N.O.S. (Contains Sulfamic acid and
PROPER SHIPPING NAME:
Hydrochloric acid), 8, PG III
HAZARD CLASS: 8
ID NUMBER: UN 3264
PACKING GROUP: III
LABEL STATEMENT: Corrosive
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
TSCA (TOXIC SUBSTANCE CONTROL ACT): All ingredients are TSCA approved.
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 03
FILE NO.:
SaniGLAZE TILE AND GROUT PREP 10/15/03
MSDS DATE:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness
or accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 04
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?STANDARD BASE 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
GLAZING COMPOUND ?STANDARD BASE
PRODUCT NAME:
None
SYNONYMS:
01-01-003/L and 01-02-002L/D
PRODUCT CODES:
Grout glazing compound
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
none
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Glycol ether DPNB 111-46-6 <1 No
ppm mg/m3
Not established Not established
OSHA PEL-TWA:
NIOSH REL - TWA: Not established Not established
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Irritation and dermatitis
Skin:
Do not take internally. May cause gastrointestinal irritation, vomiting, nausea, diarrhea, and
Ingestion:
death.
May cause severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
ACUTE HEALTH HAZARDS:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 04
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?STANDARD BASE 10/15/03
MSDS DATE:
CHRONIC HEALTH HAZARDS:
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting. Call the nearest poison control center.
INGESTION:
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly combustible - IIIB
FLAMMABLE LIMITS IN AIR:
FLASH POINT: 200癋
Closed cup
METHOD USED:
AUTOIGNITION TEMPERATURE: 癋: None
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION:
Foam, alcohol foam, CO2, dry chemical, water, or water fog.
EXTINGUISHING MEDIA:
Wear self-contained breathing apparatus and full protective gear
SPECIAL FIRE FIGHTING PROCEDURES:
for fires that involve this material.
Material does not support combustion.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Carbon monoxide, carbon dioxide, and oxides of nitrogen.
HAZARDOUS DECOMPOSITION PRODUCTS:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 04
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?STANDARD BASE 10/15/03
MSDS DATE:
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread of
liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of
in accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain residue.
All containers should be disposed of in an environmentally safe manner, and in
accordance with all governmental regulations. Keep this and all chemicals out
of the reach of children.
OTHER PRECAUTIONS: Use non-sparking utensils when handling this material. Avoid hot metal surfaces. Use
in cool, well-ventilated areas. Keep containers closed when not in use. Smoking in areas where this material is
used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
General mechanical ventilation or local exhaust is recommended when used in enclosed
VENTILATION :
areas.
Use in a well-ventilated area. When spraying this material use a NIOSH-
RESPIRATORY PROTECTION:
approved cartridge respirator suitable to keep airborne mists and vapor
concentrations below the TWA/TLV. When used in poorly-ventilated areas,
use a fresh-air supplying respirator or a self-contained breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons and protective clothing whenever possible to
OTHER PROTECTIVE CLOTHING
prevent skin contact. Use of head caps whenever possible is strongly
OR EQUIPMENT:
recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking. Eyewash stations and safety showers in the workplace are
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 04
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?STANDARD BASE 10/15/03
MSDS DATE:
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
>212 癋
BOILING POINT:
MELTING POINT:
癋
FREEZING POINT:
VAPOR PRESSURE (mmHg):
Heavier than air
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
42.92
EVAPORATION RATE (H2O = 1):
SOLUBILITY IN WATER:
66.04
PERCENT SOLIDS (BY WT):
40.78
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong acids, and oxidizing materials.
INCOMPATIBILITY (MATERIAL TO AVOID):
Carbon monoxide, carbon dioxide, and oxides of
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
nitrogen.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 04
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?STANDARD BASE 10/15/03
MSDS DATE:
SECTION 12: ECOLOGICAL INFORMATION
ECOLOGICAL
Not available
INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved
WASTE DISPOSAL METHOD:
landfill in accordance with governmental regulations. If these options are not
available, consign the recovered material to a licensed hazardous waste
contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENT:
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 04
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?STANDARD BASE 10/15/03
MSDS DATE:
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness
or accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 05
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?ACCENT BASE 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
GLAZING COMPOUND ?ACCENT BASE
PRODUCT NAME:
None
SYNONYMS:
01-01-003/A and 01-02-002A/D
PRODUCT CODES:
Grout glazing compound
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
none
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Glycol ether DPNB 111-46-6 <1 No
ppm mg/m3
Not established Not established
OSHA PEL-TWA:
NIOSH REL - TWA: Not established Not established
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Irritation and dermatitis
Skin:
Do not take internally. May cause gastrointestinal irritation, vomiting, nausea, diarrhea, and
Ingestion:
death.
May cause severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
ACUTE HEALTH HAZARDS:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 05
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?ACCENT BASE 10/15/03
MSDS DATE:
CHRONIC HEALTH HAZARDS:
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting. Call the nearest poison control center.
INGESTION:
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly combustible - IIIB
FLAMMABLE LIMITS IN AIR:
FLASH POINT: 200癋
Closed cup
METHOD USED:
AUTOIGNITION TEMPERATURE: 癋: None
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION:
Foam, alcohol foam, CO2, dry chemical, water, or water fog.
EXTINGUISHING MEDIA:
Wear self-contained breathing apparatus and full protective gear
SPECIAL FIRE FIGHTING PROCEDURES:
for fires that involve this material.
Material does not support combustion.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Carbon monoxide, carbon dioxide, and oxides of nitrogen.
HAZARDOUS DECOMPOSITION PRODUCTS:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 05
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?ACCENT BASE 10/15/03
MSDS DATE:
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread of
liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of
in accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain residue.
All containers should be disposed of in an environmentally safe manner, and in
accordance with all governmental regulations. Keep this and all chemicals out
of the reach of children.
OTHER PRECAUTIONS: Use non-sparking utensils when handling this material. Avoid hot metal surfaces. Use
in cool, well-ventilated areas. Keep containers closed when not in use. Smoking in areas where this material is
used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
General mechanical ventilation or local exhaust is recommended when used in enclosed
VENTILATION :
areas.
Use in a well-ventilated area. When spraying this material use a NIOSH-
RESPIRATORY PROTECTION:
approved cartridge respirator suitable to keep airborne mists and vapor
concentrations below the TWA/TLV. When used in poorly-ventilated areas,
use a fresh-air supplying respirator or a self-contained breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons and protective clothing whenever possible to
OTHER PROTECTIVE CLOTHING
prevent skin contact. Use of head caps whenever possible is strongly
OR EQUIPMENT:
recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking. Eyewash stations and safety showers in the workplace are
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 05
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?ACCENT BASE 10/15/03
MSDS DATE:
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
>212 癋
BOILING POINT:
MELTING POINT:
癋
FREEZING POINT:
VAPOR PRESSURE (mmHg):
Heavier than air
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
42.92
EVAPORATION RATE (H2O = 1):
SOLUBILITY IN WATER:
66.04
PERCENT SOLIDS (BY WT):
40.78
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong acids, and oxidizing materials.
INCOMPATIBILITY (MATERIAL TO AVOID):
Carbon monoxide, carbon dioxide, and oxides of
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
nitrogen.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 05
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?ACCENT BASE 10/15/03
MSDS DATE:
SECTION 12: ECOLOGICAL INFORMATION
ECOLOGICAL
Not available
INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved
WASTE DISPOSAL METHOD:
landfill in accordance with governmental regulations. If these options are not
available, consign the recovered material to a licensed hazardous waste
contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENT:
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 05
FILE NO.:
SaniGLAZE GLAZING COMPOUND ?ACCENT BASE 10/15/03
MSDS DATE:
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness
or accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 06
FILE NO.:
SaniGLAZE GLAZING COMPOUND - HARDNER 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
GLAZING COMPOUND ?HARDNER
PRODUCT NAME:
None
SYNONYMS:
01-02-004
PRODUCT CODES:
Grout glazing compound additive
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
none
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Epoxy Silane 2530-83-8 99.80 No
ppm mg/m3
OSHA PEL-TWA: 200
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Irritation and dermatitis
Skin:
Do not take internally. May cause gastrointestinal irritation, vomiting, nausea, diarrhea, and
Ingestion:
death.
May cause severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
ACUTE HEALTH HAZARDS:
CHRONIC HEALTH HAZARDS:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 06
FILE NO.:
SaniGLAZE GLAZING COMPOUND - HARDNER 10/15/03
MSDS DATE:
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
If patient is fully conscious, give two glasses of water. Induce vomiting. Obtain
INGESTION:
medical attention without delay. Treat for methanol poisoning as this material
produces methanol as it reacts with water. If medical advice is delayed, and if the
person has swallowed a moderate volume of material (a few ounces), then give
three to four ounces of hard liquor, such as whiskey. For children, give
proportionally less liquor according to weight.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to rest
INHALATION:
in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly combustible - IIIB
FLAMMABLE LIMITS IN AIR:
FLASH POINT:
METHOD USED:
AUTOIGNITION TEMPERATURE:
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 0 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION:
Foam, alcohol foam, CO2, dry chemical, water, or water fog.
EXTINGUISHING MEDIA:
Wear self-contained breathing apparatus and full protective gear
SPECIAL FIRE FIGHTING PROCEDURES:
for fires that involve this material.
Material does not support combustion.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 06
FILE NO.:
SaniGLAZE GLAZING COMPOUND - HARDNER 10/15/03
MSDS DATE:
Carbon monoxide, carbon dioxide, and oxides of nitrogen.
HAZARDOUS DECOMPOSITION PRODUCTS:
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
Eliminate ignition sources, provide good ventilation, dike spill area and
ACCIDENTAL RELEASE MEASURES:
add absorbent material or sawdust to spilled liquid.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain residue.
All containers should be disposed of in an environmentally safe manner, and in
accordance with all governmental regulations. Keep this and all chemicals out of
the reach of children.
OTHER PRECAUTIONS: Use non-sparking utensils when handling this material. Avoid hot metal surfaces. Use
in cool, well-ventilated areas. Keep containers closed when not in use. Smoking in areas where this material is
used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
General mechanical ventilation or local exhaust is recommended when used in enclosed areas.
VENTILATION :
Use in a well-ventilated area. When spraying this material use a NIOSH-
RESPIRATORY PROTECTION:
approved cartridge respirator suitable to keep airborne mists and vapor
concentrations below the TWA/TLV. When used in poorly-ventilated areas,
use a fresh-air supplying respirator or a self-contained breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons and protective clothing whenever possible to
OTHER PROTECTIVE CLOTHING
prevent skin contact. Use of head caps whenever possible is strongly
OR EQUIPMENT:
recommended.
Use proper industrial hygiene practices to minimize hazardous exposure.
WORK HYGIENIC PRACTICES:
Wash hands after handling this material, and before eating or smoking.
Eyewash stations and safety showers in the workplace are
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 06
FILE NO.:
SaniGLAZE GLAZING COMPOUND - HARDNER 10/15/03
MSDS DATE:
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
Not applicable
BOILING POINT:
MELTING POINT:
癋
FREEZING POINT:
1.0 @ 20 癈
VAPOR PRESSURE (mmHg):
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
Not applicable
EVAPORATION RATE (H2O = 1):
SOLUBILITY IN WATER:
99.8
PERCENT SOLIDS (BY WT):
0.02
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong acids, and oxidizing materials.
INCOMPATIBILITY (MATERIAL TO AVOID):
Carbon monoxide, carbon dioxide, and oxides of
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
nitrogen.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 06
FILE NO.:
SaniGLAZE GLAZING COMPOUND - HARDNER 10/15/03
MSDS DATE:
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Collect absorbent/spilled liquid mixture into metal containers. Consult local,
WASTE DISPOSAL METHOD:
state, and federal hazardous waste regulations before disposing in an approved
hazardous waste landfill.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENT:
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 06
FILE NO.:
SaniGLAZE GLAZING COMPOUND - HARDNER 10/15/03
MSDS DATE:
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness or
accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 07
FILE NO.:
SaniGLAZE DRY SOLIDS 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
DRY SOLIDS
PRODUCT NAME:
None
SYNONYMS:
01-02-003/2-oz. and 01-02-003/8-oz.
PRODUCT CODES:
Grout glazing compound additive
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
SECTION 1 NOTES: None
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Silica Crystalline - Quartz 14808-60-7 90 ?100% No
ppm mg/m3
OSHA PEL-TWA: Crystalline Quartz (respirable):
TWA 250 mppcf/(%SiO2 +5); TWA 10
mg/m3/(%SiO2 + 2)
Quartz (total dust): TWA 30
mg/m3/(%SiO2 + 2)
NIOSH REL - TWA: 0.05
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
WARNING! HARMFUL IF INHALED. OVEREXPOSURE MAY CAUSE LUNG
EMERGENCY OVERVIEW:
DAMAGE. MAY CAUSE EYE IRRITATION. INHALATION CANCER HAZARD.
CONTAINS QUARTZ WHICH CAN CAUSE CANCER. Risk of cancer depends
upon duration and level of exposure.
ROUTES OF ENTRY:
Yes
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
Shortness of breath, coughing, reduced pulmonary functions. PROLONGED INHALATION OF
Inhalation:
RESPIRABLE SILICA WILL RESULT IN PERMANENT LUNG DAMAGE OR SILICOSIS.
May cause irritation.
Skin:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 07
FILE NO.:
SaniGLAZE DRY SOLIDS 10/15/03
MSDS DATE:
Do not take internally. May cause gastrointestinal irritationor discomfort.
Ingestion:
May cause severe irritation.
Eyes:
INHALATION: Silicosis. Exposure to respirable crystalline silica (quartz) can cause
ACUTE/CHRONIC
silicosis, a fibrosis (scarring) of lungs. Silicosis may be progressive; it may lead to
HEALTH HAZARDS:
disability and death.
CANCER: There is evidence that respirable crystalline silica is a carcinogen.
SCLERODERMA: There is evidence that exposure to respirable silica is associated with
increased incidence of scleroderma, an immune system disorder manifested by fibrosis
(scarring) of lungs, skin and other internal organs.
The condition of individuals with lung disease (e.g. bronchitis,
AGGRAVATION OF PRE-EXISTING
emphysema, chronic obstructive pulmonary disease) can be aggravated
CONDITIONS:
by exposure. Individuals with Silicosis are predisposed to develop
Tuberculosis.
CARCINOGENICITY
OSHA Regulated: Yes ACGIH: Yes NTP: Yes IARC Monographs: Yes
OTHER: SUSPECTED CANCER AGENT.
SECTION 3 NOTES: Carcinogenicity Explanation - SILICA, CRYSTALLINE - QUARTZ: IARC MONOGRAPHS,
VOL 68, PG 41, 1997: GRP 1. NTP 8TH ANNUAL REPORT ON CARCINOGENS, 1998: REASONABLY
ANTICIPATED TO BE HUMAN CARCINOGEN.
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all the areas
EYES:
around the eye and lid. Get medical attention as soon as first aid has been administered.
Wash affected area with soap and water. If irritation persists, seek medical attention.
SKIN:
Give one or two glasses of water. If discomfort persists, see phsician.
INGESTION:
No specific first aid necessary since the adverse health effects associated with exposure to
INHALATION:
crystalline silica (quartz) result from chronic exposures. If there is a gross inhalation, evacuate
to a safe area with plenty of fresh air. Allow the affected individual to rest in a well-ventilated
area. If breating distress continues, seek medical aid immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
None
FLAMMABLE LIMITS IN AIR:
None
FLASH POINT:
None
METHOD USED:
None
AUTOIGNITION TEMPERATURE:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 07
FILE NO.:
SaniGLAZE DRY SOLIDS 10/15/03
MSDS DATE:
NFPA HAZARD CLASSIFICATION
HEALTH: 0 FLAMMABILITY: 0 REACTIVITY: 0
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 0 REACTIVITY: 0 PROTECTION: E
None. May be used to extinguish fires.
EXTINGUISHING MEDIA:
None
SPECIAL FIRE FIGHTING PROCEDURES:
Material does not support combustion.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
None
HAZARDOUS DECOMPOSITION PRODUCTS:
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
Clean up spill using approved, dustless methods (water or vacuum) to
ACCIDENTAL RELEASE MEASURES:
minimize generation of respirable silica particles.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid generating dust. Keep containers closed when not in use. Store in a dry,
HANDLING AND STORAGE:
cool, well-ventilated area. Empty containers may contain residue. All
containers should be disposed of in an environmentally safe manner, and in
accordance with all governmental regulations. Keep this and all chemicals out
of the reach of children.
Smoking in areas where this material is used should be strictly prohibited.
OTHER PRECAUTIONS:
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
General mechanical ventilation or local exhaust is recommended when used in enclosed
VENTILATION :
areas.
Use in a well-ventilated area. Use a NIOSH-approved respirator appropriate
RESPIRATORY PROTECTION:
for exposure to crystalline silica.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 07
FILE NO.:
SaniGLAZE DRY SOLIDS 10/15/03
MSDS DATE:
Use impermeable aprons and protective clothing whenever possible to
OTHER PROTECTIVE CLOTHING
prevent skin contact. Use of head caps whenever possible is strongly
OR EQUIPMENT:
recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating
or smoking. Eyewash stations and safety showers in the workplace are
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Fine-grained sand
APPEARANCE:
None
ODOR:
Solid
PHYSICAL STATE:
Not applicable
pH AS SUPPLIED:
Not applicable
pH (Other):
4046 癋
BOILING POINT:
Not applicable
MELTING POINT:
Not applicable
FREEZING POINT:
None
VAPOR PRESSURE (mmHg):
None
VAPOR DENSITY (AIR = 1):
2.65
SPECIFIC GRAVITY (H2O = 1):
Not applicable
EVAPORATION RATE (H2O = 1):
None
SOLUBILITY IN WATER:
100
PERCENT SOLIDS (BY WT):
0
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Avoid contact with powerful oxidizing agents such as fluorine,
CONDITIONS TO AVOID (STABILITY):
chlorine trifluoride, oxygen difluoride - may cause fires.
Avoid contact with powerful oxidizing agents such as fluorine,
INCOMPATIBILITY (MATERIAL TO AVOID):
chlorine trifluoride, oxygen difluoride - may cause fires.
Silica will dissolve in hydrofluoric acid and produce a
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
corrosive gas - silicon tetrafluoride.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 07
FILE NO.:
SaniGLAZE DRY SOLIDS 10/15/03
MSDS DATE:
SECTION 11: TOXICOLOGICAL INFORMATION
The major concern associated with exposure to respirable crystalline silica is
TOXICOLOGICAL INFORMATION:
silicosis, caused by inhalation and retention of respirble crystalline silica
dust. Chronic silicosis can occur after many years of exposure to relatively
low levels of airborne respirable crystalline silica dust.
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Crystalline silica (quartz) is not ecotoxic, i.e., there is no data which suggests
ECOLOGICAL INFORMATION:
that crystalline silica is toxic to birds, fish, invertebrates, microorganisms or
plants.
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Packaging and product may be landfilled; however, material should be covered to
WASTE DISPOSAL METHOD:
minimize generation of airborne dust. Crystalline silica (quartz) is not classified as
a hazardous waste under RCRA regulations at 40 CFR 261 et. seq. Disposal
must be in accordance with federal, state and local regulations.
None
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME: None
HAZARD CLASS: None
ID NUMBER: None
PACKING GROUP: None
LABEL STATEMENT: None
None
OTHER AGENCIES:
SECTION 14 NOTES: Crystalline silica (quartz) is not a hazardous material for the purpose of transportation under
the U.S. Department Of Transportation Table of Hazardous Materials, 49 CFR 172.101.
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
Hazardous substance release reporting not required
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 07
FILE NO.:
SaniGLAZE DRY SOLIDS 10/15/03
MSDS DATE:
Hazardous releases reporting not required
Section 304:
Reporting is not required
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting is not required
Section 313:
STATE REGULATIONS: CALIFORNIA PROPOSITION 65 - Crystalline silica (quartz) is classified as a
substance known to the state of California to be a carcinogen.
Not applicable
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
None
OTHER INFORMATION:
SaniGLAZE International, LLC and MACTEC Engineering and Consulting, Inc.
DISCLAIMER:
provide the information contained herein in good faith but make no representation
as to its comprehensiveness or accuracy. This document is intended only as a
guide to the appropriate precautionary handling of the material by a properly
trained person using this product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 08A
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION - LOW VOC 5/31/07
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
CLEAN UP SOLUTION - LOW VOC
PRODUCT NAME:
None
SYNONYMS:
01-01-004
PRODUCT CODES:
Tile surface cleaning and preparation
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
115 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Acetone 67-64-1 <10 No
ppm mg/m3
OSHA PEL-TWA: 500 Not established
NIOSH REL - TWA: 500 Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Isopropanol 0067-63-0 ~5 No
ppm mg/m3
OSHA PEL-TWA: 400 Not established
Not established
NIOSH REL - TWA: 400
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Butyl Carbitol 0112-34-5 <5 No
ppm mg/m3
OSHA PEL-TWA: --- Not established
NIOSH REL - TWA: --- Not established
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
ROUTES OF ENTRY:
Yes (mists)
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 08
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION 10/15/03
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
CLEAN UP SOLUTION
PRODUCT NAME:
None
SYNONYMS:
01-01-004
PRODUCT CODES:
Tile surface cleaning and preparation
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 >80 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
Isopropanol 67-63-0 <12 Yes
ppm mg/m3
400 980
OSHA PEL-TWA:
NIOSH REL - TWA: 400 980
SECTION 2 NOTES: None
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes (mists)
Inhalation:
Yes
Skin:
Yes
Ingestion:
Yes
Eyes:
POTENTIAL HEALTH EFFECTS:
If sprayed or misted may cause chemical pneumonitis, irritation, or chemical burns. This product
Inhalation:
is not toxic by inhalation.
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 08
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION 10/15/03
MSDS DATE:
Minimally irritating. Prolonged contact may cause dermatitis, drying of skin.
Skin:
Do not take internally. Contains isopropanol. Can cause blindness if ingested. May cause
Ingestion:
nausea, gastrointestinal distress or diarrhea.
May cause temporary eye irritation.
Eyes:
The toxicological properties of this compound have not been fully tested.
ACUTE HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
The toxicological properties of this compound have not been fully tested.
CHRONIC HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
Contact or breathing mists may exacerbate existing skin or respiratory
AGGRAVATION OF PRE-EXISTING
disorders.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse. Discard contaminated leather articles.
DO NOT induce vomiting. Drink 3-4 glasses of milk or water, and call the nearest
INGESTION:
poison control center.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
FLAMMABLE LIMITS IN AIR, UPPER: None
LOWER: None
癋: None
FLASH POINT:
癈: None
None
METHOD USED:
癋: None
AUTOIGNITION TEMPERATURE:
癈: None
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 08
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION 10/15/03
MSDS DATE:
HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 0 REACTIVITY: 0 PROTECTION:
Not applicable
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, and other
HAZARDOUS DECOMPOSITION PRODUCTS:
unidentified fragments if this product is involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread
of liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of
in accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Avoid contact with skin and eyes. Keep containers closed when not in use.
HANDLING AND STORAGE:
Store in a dry, cool, well-ventilated area. Empty containers may contain residue.
All containers should be disposed of in an environmentally safe manner, and in
accordance with all governmental regulations. Keep this and all chemicals out of
the reach of children.
OTHER PRECAUTIONS: None
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed.
Safety glasses (ANSI Z87.1) or approved equivalent as necessary to minimize eye
EYE PROTECTION:
contact hazards.
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 08
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION 10/15/03
MSDS DATE:
Neoprene or other materials may be used if there is documented evidence of
SKIN PROTECTION:
compatibility.
Neoprene aprons, overshoes, oversleeves or other impervious clothing
OTHER PROTECTIVE CLOTHING
as necessary to minimize exposure.
OR EQUIPMENT:
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Slightly hazy liquid
APPEARANCE:
Faint banana-like odor
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
>218 癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
4
VAPOR PRESSURE (mmHg):
Same as water
VAPOR DENSITY (AIR = 1):
0.97
SPECIFIC GRAVITY (H2O = 1):
>1
EVAPORATION RATE(H2O = 1):
Water miscible
SOLUBILITY IN WATER:
PERCENT SOLIDS BY WEIGHT:
PERCENT VOLATILE (BY WT):
SECTION 9 NOTES: None
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
None
CONDITIONS TO AVOID (STABILITY):
Strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 08
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION 10/15/03
MSDS DATE:
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved
WASTE DISPOSAL METHOD:
landfill in accordance with governmental regulations. If these options are not
available, consign the recovered material to a licensed hazardous waste
contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME: Compound, Cleaning liquid (non-hazardous)
HAZARD CLASS: None
ID NUMBER: None
PACKING GROUP: None
LABEL STATEMENT: None
None
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 08
FILE NO.:
SaniGLAZE CLEAN UP SOLUTION 10/15/03
MSDS DATE:
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness
or accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 11/08/04
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
SUPER SHIELD 4
PRODUCT NAME:
None
SYNONYMS:
01-02-016
PRODUCT CODES:
Tile surface sealer
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 <65 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
DGMB Glycol Ether 112-34-5 <3 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
% WT SARA 313 REPORTABLE
INGREDIENT CAS NO.
DEH Glycol Ether 112-59-4 <6 No
ppm
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 11/08/04
MSDS DATE:
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
No
Skin:
Yes
Ingestion:
No
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Minimally irritating. Prolonged contact may cause dermatitis, drying of skin.
Skin:
Do not take internally. May cause nausea, gastrointestinal distress, diarrhea or death.
Ingestion:
Severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
The toxicological properties of this compound have not been fully tested.
ACUTE HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
The toxicological properties of this compound have not been fully tested.
CHRONIC HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, and vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting, can cause chemical pneumonitis and pulmonary edema.
INGESTION:
Contact physician immediately.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly Combustible, IIIB
FLAMMABLE LIMITS IN AIR:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 11/08/04
MSDS DATE:
癋: 200
FLASH POINT:
癈:
Closed cup
METHOD USED:
癋: Not determined
AUTOIGNITION TEMPERATURE:
癈: Not determined
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION:
Foam, alcohol foam, CO2, dry chemical, water or water fog.
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Respiratory equipment should be worn to avoid inhalation of
concentrated vapors.
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, oxides of
HAZARDOUS DECOMPOSITION PRODUCTS:
nitrogen, and other unidentified fragments if this product is
involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread of
liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of in
accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Use non-sparking utensils when handling this material. Avoid hot metal
HANDLING AND STORAGE:
surfaces. Avoid contact with skin and eyes. Keep away from excessive heat or
open flames. Keep containers closed when not in use. Use and store in a dry,
cool, well-ventilated area. Empty containers may contain residue. All containers
should be disposed of in an environmentally safe manner, and in accordance
with all governmental regulations. Keep this and all chemicals out of the reach
of children.
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 11/08/04
MSDS DATE:
OTHER PRECAUTIONS: Smoking in areas where this material is used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed. When using in poorly ventilated and
confined spaces, use a fresh-air supplying respirator of a self-contained
breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons, overshoes, oversleeves or other protective
OTHER PROTECTIVE CLOTHING
clothing as necessary to minimize exposure. The use of head caps
OR EQUIPMENT:
whenever possible is strongly recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking. Eyewashes and safety showers in the workplace are
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
212 - 497癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
VAPOR PRESSURE (mmHg):
Heavier than air
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
EVAPORATION RATE (ethyl ether =
107.49
1):
SOLUBILITY IN WATER:
20.6
PERCENT SOLIDS BY WEIGHT:
81.0
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 11/08/04
MSDS DATE:
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved landfill
WASTE DISPOSAL METHOD:
in accordance with governmental regulations. If these options are not available,
consign the recovered material to a licensed hazardous waste contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS: None
ID NUMBER: None
PACKING GROUP: None
LABEL STATEMENT: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 11/08/04
MSDS DATE:
None
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness or
accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
SUPER SHIELD 5 FLAT
PRODUCT NAME:
None
SYNONYMS:
01-02-018-F
PRODUCT CODES:
Tile surface sealer
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 <65 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
EH Glycol Ether 112-25-4 <3 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
% WT SARA 313 REPORTABLE
INGREDIENT CAS NO.
PPH Glycol Ether 770-35-4 <2 No
ppm
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
No
Skin:
Yes
Ingestion:
No
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Minimally irritating. Prolonged contact may cause dermatitis, drying of skin.
Skin:
Do not take internally. May cause nausea, gastrointestinal distress, diarrhea or death.
Ingestion:
Severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
The toxicological properties of this compound have not been fully tested.
ACUTE HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
The toxicological properties of this compound have not been fully tested.
CHRONIC HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, and vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting, can cause chemical pneumonitis and pulmonary edema.
INGESTION:
Contact physician immediately.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly Combustible, IIIB
FLAMMABLE LIMITS IN AIR:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
癋: 200
FLASH POINT:
癈:
Closed cup
METHOD USED:
癋: Not determined
AUTOIGNITION TEMPERATURE:
癈: Not determined
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION: 1
Foam, alcohol foam, CO2, dry chemical, water or water fog.
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Respiratory equipment should be worn to avoid inhalation of
concentrated vapors.
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, oxides of
HAZARDOUS DECOMPOSITION PRODUCTS:
nitrogen, and other unidentified fragments if this product is
involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread of
liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of in
accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Use non-sparking utensils when handling this material. Avoid hot metal
HANDLING AND STORAGE:
surfaces. Avoid contact with skin and eyes. Keep away from excessive heat or
open flames. Keep containers closed when not in use. Use and store in a dry,
cool, well-ventilated area. Empty containers may contain residue. All containers
should be disposed of in an environmentally safe manner, and in accordance
with all governmental regulations. Keep this and all chemicals out of the reach
of children.
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
OTHER PRECAUTIONS: Smoking in areas where this material is used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed. When using in poorly ventilated and
confined spaces, use a fresh-air supplying respirator of a self-contained
breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons, overshoes, oversleeves or other protective
OTHER PROTECTIVE CLOTHING
clothing as necessary to minimize exposure. The use of head caps
OR EQUIPMENT:
whenever possible is strongly recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking. Eyewashes and safety showers in the workplace are
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
212 - 497癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
VAPOR PRESSURE (mmHg):
Heavier than air
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
EVAPORATION RATE (ethyl ether =
74.9
1):
SOLUBILITY IN WATER:
22.4
PERCENT SOLIDS BY WEIGHT:
79.5
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved landfill
WASTE DISPOSAL METHOD:
in accordance with governmental regulations. If these options are not available,
consign the recovered material to a licensed hazardous waste contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS: None
ID NUMBER: None
PACKING GROUP: None
LABEL STATEMENT: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
None
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness or
accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
SUPER SHIELD 5 GLOSS
PRODUCT NAME:
None
SYNONYMS:
01-02-018-G
PRODUCT CODES:
Tile surface sealer
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 <65 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
EH Glycol Ether 112-25-4 <3 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
% WT SARA 313 REPORTABLE
INGREDIENT CAS NO.
PPH Glycol Ether 770-35-4 <3 No
ppm
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
No
Skin:
Yes
Ingestion:
No
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Minimally irritating. Prolonged contact may cause dermatitis, drying of skin.
Skin:
Do not take internally. May cause nausea, gastrointestinal distress, diarrhea or death.
Ingestion:
Severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
The toxicological properties of this compound have not been fully tested.
ACUTE HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
The toxicological properties of this compound have not been fully tested.
CHRONIC HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, and vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting, can cause chemical pneumonitis and pulmonary edema.
INGESTION:
Contact physician immediately.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly Combustible, IIIB
FLAMMABLE LIMITS IN AIR:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
癋: 200
FLASH POINT:
癈:
Closed cup
METHOD USED:
癋: Not determined
AUTOIGNITION TEMPERATURE:
癈: Not determined
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION: 1
Foam, alcohol foam, CO2, dry chemical, water or water fog.
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Respiratory equipment should be worn to avoid inhalation of
concentrated vapors.
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, oxides of
HAZARDOUS DECOMPOSITION PRODUCTS:
nitrogen, and other unidentified fragments if this product is
involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread of
liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of in
accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Use non-sparking utensils when handling this material. Avoid hot metal
HANDLING AND STORAGE:
surfaces. Avoid contact with skin and eyes. Keep away from excessive heat or
open flames. Keep containers closed when not in use. Use and store in a dry,
cool, well-ventilated area. Empty containers may contain residue. All containers
should be disposed of in an environmentally safe manner, and in accordance
with all governmental regulations. Keep this and all chemicals out of the reach
of children.
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
OTHER PRECAUTIONS: Smoking in areas where this material is used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed. When using in poorly ventilated and
confined spaces, use a fresh-air supplying respirator of a self-contained
breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons, overshoes, oversleeves or other protective
OTHER PROTECTIVE CLOTHING
clothing as necessary to minimize exposure. The use of head caps
OR EQUIPMENT:
whenever possible is strongly recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking. Eyewashes and safety showers in the workplace are
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
212 - 497癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
VAPOR PRESSURE (mmHg):
Heavier than air
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
EVAPORATION RATE (ethyl ether =
74.3
1):
SOLUBILITY IN WATER:
20.8
PERCENT SOLIDS BY WEIGHT:
81.2
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved landfill
WASTE DISPOSAL METHOD:
in accordance with governmental regulations. If these options are not available,
consign the recovered material to a licensed hazardous waste contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS: None
ID NUMBER: None
PACKING GROUP: None
LABEL STATEMENT: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
None
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness or
accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
SUPER SHIELD 5 SEMI-GLOSS
PRODUCT NAME:
None
SYNONYMS:
01-02-018-S
PRODUCT CODES:
Tile surface sealer
PRODUCT USE:
SaniGLAZE International, LLC
MANUFACTURER:
123 Park Street
ADDRESS:
Jacksonville, Florida 32204
(800) 255-3924 CHEM-TEL (Chemical Emergencies Only)
EMERGENCY PHONE:
(800) 874-5554
OTHER CALLS (Product Information):
(904) 366-2690
FAX PHONE:
MACTEC Engineering and Consulting, Inc.
PREPARED BY:
3901 Carmichael Avenue
Jacksonville, Florida 32207
None
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS NO. % WT SARA 313 REPORTABLE
Water 7732-18-5 <65 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
CAS NO. % WT SARA 313 REPORTABLE
INGREDIENT
EH Glycol Ether 112-25-4 <3 No
ppm mg/m3
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
% WT SARA 313 REPORTABLE
INGREDIENT CAS NO.
PPH Glycol Ether 770-35-4 <3 No
ppm
OSHA PEL-TWA: Not established Not established
NIOSH REL - TWA: Not established Not established
PAGE 1 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
ROUTES OF ENTRY:
Yes
Inhalation:
No
Skin:
Yes
Ingestion:
No
Eyes:
POTENTIAL HEALTH EFFECTS:
Dizziness, breathing difficulty, headaches, loss of coordination, unconsciousness, and death.
Inhalation:
Minimally irritating. Prolonged contact may cause dermatitis, drying of skin.
Skin:
Do not take internally. May cause nausea, gastrointestinal distress, diarrhea or death.
Ingestion:
Severe irritation, tearing, redness, blurred vision, and blindness.
Eyes:
The toxicological properties of this compound have not been fully tested.
ACUTE HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
The toxicological properties of this compound have not been fully tested.
CHRONIC HEALTH HAZARDS:
Similar compounds are essentially non-toxic.
AGGRAVATION OF PRE-EXISTING
Anesthesia, respiratory tract irritation, dermatitis, nausea, and vomiting.
CONDITIONS:
CARCINOGENICITY
OSHA Regulated: No ACGIH: No NTP: No IARC Monographs: No
OTHER: None
SECTION 3 NOTES: None
SECTION 4: FIRST AID MEASURES
Flush with water for 15 minutes. Lift the eyelids while flushing to decontaminate all
EYES:
the areas around the eye and lid. Get medical attention as soon as first aid has
been administered.
Remove contaminated clothing. Wash affected area with soap and water. If
SKIN:
irritation persists, seek medical attention. Decontaminate clothing and shoes
before reuse.
DO NOT induce vomiting, can cause chemical pneumonitis and pulmonary edema.
INGESTION:
Contact physician immediately.
Evacuate to a safe area with plenty of fresh air. Allow the affected individual to
INHALATION:
rest in a well-ventilated area. If breating distress continues, seek medical aid
immediately.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: None
SECTION 4 NOTES: None
SECTION 5: FIRE-FIGHTING MEASURES
Slightly Combustible, IIIB
FLAMMABLE LIMITS IN AIR:
PAGE 2 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
癋: 200
FLASH POINT:
癈:
Closed cup
METHOD USED:
癋: Not determined
AUTOIGNITION TEMPERATURE:
癈: Not determined
NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION: 1
Foam, alcohol foam, CO2, dry chemical, water or water fog.
EXTINGUISHING MEDIA:
Keep containers cooled with a water spray if involved in a fire.
SPECIAL FIRE FIGHTING PROCEDURES:
Respiratory equipment should be worn to avoid inhalation of
concentrated vapors.
None
UNUSUAL FIRE AND EXPLOSION HAZARDS:
May evolve carbon monoxide, carbon dioxide, oxides of
HAZARDOUS DECOMPOSITION PRODUCTS:
nitrogen, and other unidentified fragments if this product is
involved in a fire.
SECTION 5 NOTES: None
SECTION 6: ACCIDENTAL RELEASE MEASURES
DO NOT contaminate municipal sewers or other open bodies of water
ACCIDENTAL RELEASE MEASURES:
with runoff. Wear recommended protective clothing. Remove
contaminated garments promptly. Remove unnecessary personnel
from the area. Floors may be slippery; use care to avoid falling. Dike
the spill immediately with appropriate materials to prevent the spread of
liquid. Absorb the liquid with an inert absorbent such as sand, dirt,
vermiculite or "oil-dri", or use commercial absorbent pads. Transfer
liquids and solid diking material tp suitable containers, and dispose of in
accordance with local, state, and federal regulations.
SECTION 6 NOTES: None
SECTION 7: HANDLING AND STORAGE
Use non-sparking utensils when handling this material. Avoid hot metal
HANDLING AND STORAGE:
surfaces. Avoid contact with skin and eyes. Keep away from excessive heat or
open flames. Keep containers closed when not in use. Use and store in a dry,
cool, well-ventilated area. Empty containers may contain residue. All containers
should be disposed of in an environmentally safe manner, and in accordance
with all governmental regulations. Keep this and all chemicals out of the reach
of children.
PAGE 3 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
OTHER PRECAUTIONS: Smoking in areas where this material is used should be strictly prohibited.
SECTION 7 NOTES: None
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
None
ENGINEERING CONTROLS:
Local exhaust is recommended when used in enclosed areas.
VENTILATION :
Use in a well-ventilated area. If mist is being generated and exceeds the
RESPIRATORY PROTECTION:
TLV, a respiratory protection program meeting OSHA 1910.134 and ANSI
Z88.2 requirements must be followed. When using in poorly ventilated and
confined spaces, use a fresh-air supplying respirator of a self-contained
breathing apparatus.
Use chemical safety glasses, goggles, and face shields for eye protection.
EYE PROTECTION:
Use impermeable chemical handling gloves for skin protection.
SKIN PROTECTION:
Use impermeable aprons, overshoes, oversleeves or other protective
OTHER PROTECTIVE CLOTHING
clothing as necessary to minimize exposure. The use of head caps
OR EQUIPMENT:
whenever possible is strongly recommended.
Use proper industrial hygiene practices to minimize hazardous
WORK HYGIENIC PRACTICES:
exposure. Wash hands after handling this material, and before eating or
smoking. Eyewashes and safety showers in the workplace are
recommended.
EXPOSURE GUIDELINES:
SECTION 8 NOTES: None
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
ODOR:
Liquid
PHYSICAL STATE:
pH AS SUPPLIED:
pH (Other):
212 - 497癋
BOILING POINT:
<32 癋
MELTING POINT:
癋
FREEZING POINT:
VAPOR PRESSURE (mmHg):
Heavier than air
VAPOR DENSITY (AIR = 1):
SPECIFIC GRAVITY (H2O = 1):
EVAPORATION RATE (ethyl ether =
74.3
1):
SOLUBILITY IN WATER:
20.8
PERCENT SOLIDS BY WEIGHT:
81.2
PERCENT VOLATILE (BY VOL):
SECTION 9 NOTES: None
PAGE 4 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
SECTION 10: STABILITY AND REACTIVITY
Stable
STABILITY:
Excessive heat, poor ventilation, corrosive atmospheres, excessive
CONDITIONS TO AVOID (STABILITY):
aging.
Alkaline materials, strong oxidizers, strong acids
INCOMPATIBILITY (MATERIAL TO AVOID):
May evolve carbon monoxide, carbon dioxide, and
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
other unidentified fragments if this product is involved
in a fire.
Will not occur
HAZARDOUS POLYMERIZATION:
None
CONDITIONS TO AVOID (POLYMERIZATION):
SECTION 10 NOTES: None
SECTION 11: TOXICOLOGICAL INFORMATION
The toxicological properties of this compound have not been fully tested.
TOXICOLOGICAL INFORMATION:
SECTION 11 NOTES: None
SECTION 12: ECOLOGICAL INFORMATION
Not available
ECOLOGICAL INFORMATION:
SECTION 12 NOTES: None
SECTION 13: DISPOSAL CONSIDERATIONS
Incinerate this material and all associated wastes, or bury in an approved landfill
WASTE DISPOSAL METHOD:
in accordance with governmental regulations. If these options are not available,
consign the recovered material to a licensed hazardous waste contractor.
RCRA HAZARD CLASS:
SECTION 13 NOTES: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS: None
ID NUMBER: None
PACKING GROUP: None
LABEL STATEMENT: None
PAGE 5 OF 6
MATERIAL SAFETY DATA SHEET 09A
FILE NO.:
SaniGLAZE SUPER SHIELD 1/25/06
MSDS DATE:
None
OTHER AGENCIES:
SECTION 14 NOTES: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
All ingredients are TSCA approved.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
EHS reporting not required
Setion 302:
Hazardous releases reporting not required
Section 304:
Reporting is required if inventory exceeds the threshold planning quantity
Section 311:
Inventory data reporting is not required
Section 312:
Emissions and release reporting may be required for users of this product within the
Section 313:
manufacturing sector. This does not apply to service companies.
STATE REGULATIONS:
INTERNATIONAL REGULATIONS:
SECTION 15 NOTES: None
SECTION 16: OTHER INFORMATION
OTHER INFORMATION:
PREPARATION INFORMATION:
MACTEC Engineering and Consulting, Inc. provides the information contained
DISCLAIMER:
herein in good faith but makes no representation as to its comprehensiveness or
accuracy. This document is intended only as a guide to the appropriate
precautionary handling of the material by a properly trained person using this
product.
PAGE 6 OF 6
|