3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
Material Safety Data Sheet
Copyright, 2005, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use)
MANUFACTURER: 3M
DIVISION: Commercial Care Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 08/22/2005 Downloaded 4/3/2007
Supercedes Date: 03/02/2004
Document Group: 19-0066-1
Product Use:
Specific Use: Designed to remove most common spots and stains from carpeting and upholstery.
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
WATER 7732-18-5 60 - 90
1-METHOXY-2-PROPANOL 107-98-2 7 - 13
2-BUTOXYETHANOL 111-76-2 7 - 13
SODIUM MONO-C10-16-ALKYL SULFATES 68585-47-7 1.5 - 10
SODIUM LAUROYL SARCOSINATE 137-16-6 1- 5
ALCOHOLS, C12-14, ETHOXYLATED PROPOXYLATED 68439-51-0 < 0.5
2-METHOXY-1-PROPANOL 1589-47-5 < 0.5
2,5-FURANDIONE, TELOMER WITH ETHENYLBENZENE AND (1- 52720-34-0 < 0.5
METHYLETHYLl)BENZENE, AMMONIUM SALT
FRAGRANCE OIL Unknown < 0.5
DODECANOIC ACID, SODIUM SALT 629-25-4 < 0.5
_________________________________________________________________________________________________
Page 1 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: Liquid
Odor, Color, Grade: Clear dark turquoise, citrus floral fragrance
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: May cause allergic skin reaction. May cause target organ effects.
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
May be absorbed through skin and cause target organ effects.
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Prolonged or repeated exposure may cause:
Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and
jaundice.
Kidney/Bladder Effects: Signs/symptoms may include changes in urine production, abdominal or lower back pain, increased
protein in urine, increased blood urea nitrogen (BUN), blood in urine, and painful urination.
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
SECTION 4: FIRST AID MEASURES
_________________________________________________________________________________________________
Page 2 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
> 200 篎
Flash Point
Class IIIB Combustible Liquid
OSHA Flammability Classification:
5.2 EXTINGUISHING MEDIA
Ordinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Non-flammable: ordinary combustible material.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more
information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be
cleaned up by qualified personnel. Ventilate the area with fresh air. Contain spill. Working from around the edges of the spill
inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it
appears dry. Collect as much of the spilled material as possible. Clean up residue with water. Place in a closed container approved
for transportation by appropriate authorities. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
_________________________________________________________________________________________________
Page 3 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
Keep out of the reach of children. Avoid breathing of vapors, mists or spray. Avoid skin contact. Avoid eye contact with vapors,
mists, or spray. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
7.2 STORAGE
Store under normal warehouse conditions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use in a well-ventilated area.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber, Neoprene, Nitrile Rubber.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray. Under normal use conditions, airborne exposures are not expected to be significant enough
to require respiratory protection.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
1-METHOXY-2-PROPANOL ACGIH TWA 100 ppm
1-METHOXY-2-PROPANOL ACGIH STEL 150 ppm
1-METHOXY-2-PROPANOL OSHA TWA 100 ppm Table Z-1A
1-METHOXY-2-PROPANOL OSHA STEL 150 ppm Table Z-1A
2-BUTOXYETHANOL ACGIH TWA 20 ppm Table A3
2-BUTOXYETHANOL OSHA TWA, Vacated 25 ppm Skin Notation*
2-BUTOXYETHANOL OSHA TWA 50 ppm Skin Notation*; Table Z-1
POLYETHYLENE GLYCOLS AIHA TWA, as aerosol 10 mg/m3
* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
_________________________________________________________________________________________________
Page 4 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Liquid
Specific Physical Form:
Clear dark turquoise, citrus floral fragrance
Odor, Color, Grade:
Liquid
General Physical Form:
> 200 篎
Flash Point
Approximately 200 篎
Boiling point
Approximately 0.9 [Ref Std: WATER=1]
Specific Gravity
7.5
pH
Complete
Solubility in Water
10 - 20 % [Test Method: calculated per CARB title 2]
Volatile Organic Compounds
700 - 1300 g/l [Test Method: calculated per CARB title 2]
VOC Less H2O & Exempt Solvents
< 100 centipoise
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
A 3M Product Environmental Data Sheet (PED) is available.
CHEMICAL FATE INFORMATION
_________________________________________________________________________________________________
Page 5 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
A 3M Product Environmental Data Sheet (PED) is available.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Discharge spent solutions and small quantities (less than 5 gal.(19 L)) to a wastewater treatment system.
Reduce discharge rate if foaming occurs. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical
waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
2-BUTOXYETHANOL (GLYCOL ETHERS) 111-76-2 7 - 13
STATE REGULATIONS
_________________________________________________________________________________________________
Page 6 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
All the components of this product are listed on China's Inventory of Chemical Substances.
The components of this product are listed on the Canadian Domestic Substances List.
INTERNATIONAL REGULATIONS
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 1 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 2 Flammability: 1 Reactivity: 0 Protection: X - See PPE section.
Hazardous Material Identification System (HMIS? hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS?ratings are to be used with a fully implemented HMIS?program. HMIS?is a registered mark of the National Paint and Coatings
Association (NPCA).
Revision Changes:
Section 1: Product name was modified.
Section 1: Product use information was modified.
Section 16: NFPA hazard classification heading was modified.
Section 16: HMIS hazard classification heading was modified.
Section 3: Other potential health effects heading was modified.
Copyright was modified.
Section 8: Exposure guidelines data source legend was modified.
Section 4: First aid for eye contact - decontamination - was modified.
Section 4: First aid for eye contact - medical assistance - was modified.
Section 3: Potential effects from skin contact information was modified.
Section 3: Potential effects from inhalation information was modified.
Section 3: Potential effects from ingestion information was modified.
Section 7: Handling information was modified.
Section 8: Respiratory protection information was modified.
Section 8: Eye/face protection information was modified.
Section 15: 311/312 hazard categories heading was modified.
Section 4: First aid for skin contact - medical assistance - was modified.
_________________________________________________________________________________________________
Page 7 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
Section 4: First aid for inhalation - termination of exposure - was modified.
Section 4: First aid for inhalation - medical assistance - was modified.
Section 4: First aid for ingestion (swallowing) - medical assistance - was modified.
Section 10: Hazardous polymerization heading was modified.
Section 3: Immediate other hazard(s) was modified.
Section 2: Ingredient table was modified.
Section 3: Other health effects information was modified.
Section 16: HMIS explanation was modified.
Section 16: NFPA explanation was modified.
Page Heading: Product name was modified.
Section 15: Inventories information was modified.
Section 15: EPCRA 313 information was modified.
Section 15: EPCRA 313 text was modified.
Section 12: Ecotoxicological information heading was modified.
Section 12: Chemical fate information heading was modified.
Section 8: Exposure guidelines ingredient information was modified.
Section 8: Exposure guidelines legend was modified.
Section 8: Exposure guideline note was modified.
Section 9: Property description for optional properties was modified.
Section 1: Initial issue message was modified.
Section 16: NFPA hazard classification for special hazards was modified.
Section 12: Ecotoxicological phrase was modified.
Section 12: Chemical Fate phrase was modified.
Section 3: Immediate skin hazard(s) was added.
Section 4: First aid for skin contact - termination of exposure - was added.
Section 4: First aid for skin contact - handling - was added.
Sections 3 and 9: Specific physical form information was added.
Sections 3 and 9: Specific physical form heading was added.
Section 2: Ingredient phrase was added.
Section 3: Other health effects information (reproductive hazards) was added.
Section 9: Density information was deleted.
Section 9: Vapor density value was deleted.
Section 9: Vapor pressure value was deleted.
Section 5: Flammable limits (UE) information was deleted.
Section 5: Flammable limits (LEL) information was deleted.
Section 5: Autoignition temperature information was deleted.
Section 9: Melting point information was deleted.
Section 9: Flammable limits (LEL) information was deleted.
Section 9: Flammable limits (UEL) information was deleted.
Section 9: Autoignition temperature information was deleted.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
_________________________________________________________________________________________________
Page 8 of 9
3M MATERIAL SAFETY DATA SHEET COMPUBLEND (TM) II SPOT/STAIN REMOVER (Ready-to-Use) 08/22/2005
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 9 of 9
|