TARGET COATINGS, Inc.
54 SINDLE AVENUE
LITTLE FALLS, NEW JERSEY 07424 USA
800-752-9922
www.targetcoatings.com
MATERIAL SAFETY DATA SHEET PAGE 1 OF 4
____________________________________________________________________________________
SECTION I PRODUCT IDENTIFICATION
____________________________________________________________________________
Product Trade Name: EM6000 Production Lacquer
(6000, 6200, 6300, 6400)
Chemical Name: Compound, Coating
Manufacturer: Target Coatings, Inc.
Effective Date: January 1, 2009..Revision 1
____________________________________________________________________________
SECTION II PHYSICAL DATA
____________________________________________________________________________
Boiling Point: 212 F
Freezing Point: 30F
Weight Per Gallon: 8.66 lbs. / Gal.
Vapor Density: Heavier then Air.
Evaporation Rate: Slower then N-Butyl Acetate
Solubility in Water: Infinitely miscible
pH: 8.0 ?8.5
Appearance and Odor: Translucent Liquid, Acrylic Odor
VOC Content: 31 Grams /Litre
HAPS Content: 0
____________________________________________________________________________
SECTION III COMPOSITION INFORMATION
____________________________________________________________________________
INGREDIENT Approx. Wt% SARA-313 CAS#
Acrylic Copolymer Resin 30 max. N/A 63744-68-3
Dipropylene Glycol Monomethyl Ether 05 max. N/A 34590-94-2
Propylene Glycol Monomethyl Ether 05 max. N/A 107-98-2
Water 60 max. N/A 7732-18-5
____________________________________________________________________________
SECTION IV HAZARDOUS INGREDIENTS
____________________________________________________________________________
INGREDIENT Approx. Wt% TLV PEL(TWA) STEL CAS#
None Of The Ingredients In This Product Meet The Definition Of "Hazardous Chemical"
Given In The OSHA Hazard Communication Regulation 29CFR 1910.120 (C)
____________________________________________________________________________
MATERIAL SAFETY DATA SHEET PAGE 2 OF 4
____________________________________________________________________________________
SECTION V TOXICOLOGICAL PROPERTIES
____________________________________________________________________________________
LD50: Not determined
Threshold Limit Value: No limit determined
Effects of Acute Exposure:
Ingestion: Intense mucous membrane irritation
Inhalation: Prolonged exposure may produce
headaches, and mucous membrane
irritation.
Skin Contact: Direct contact will cause irritation
Eye Contact: Direct contact will cause extensive
irritation
Effects of Chronic Exposure: None determined
____________________________________________________________________________
SECTION VI PREVENTIVE MEASURES
____________________________________________________________________________
INDUSTRIAL HYGIENE IN THE WORKPLACE
RESPIRATORY PROTECTION: An approved organic-vapor full-face respirator is advised for
poor ventilation or spray applications.
VENTILATION: LOCAL EXHAUST- None required
MECHANICAL(GENERAL)- Provide adequate ventilation.
PROTECTIVE GLOVES: Wear rubber gloves.
EYE PROTECTION: Wear approved safety glasses with side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective work clothes.
STORAGE AND HANDLING PROCEDURES
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: store at 40F-90F. this product
is safe for consumer resale. Keep from freezing. Keep away from Fire and Heat (Any ignition
source). Keep containers closed when not in use. Provide adequate ventilation.
KEEP OUT OF REACH OF CHILDREN
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Halt spill at source
and contain or dike spill with inert absorbent material. Transfer liquid to containers for recovery
or disposal. Shovel absorbent into drums for disposal in accordance with local, state, and
federal regulations.
RECOMMENDED WASTE DISPOSAL METHODS: Material should not be flushed into sewer
system. If this material becomes a waste, it does not meet the criteria of a hazardous waste as
defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261, since it has
neither the characteristics of Subpart C nor listed in Subpart D. After the material has been
collected, dispose of in accordance with regulations applicable to non-hazardous liquid wastes.
MATERIAL SAFETY DATA SHEET Page 3 of 4
____________________________________________________________________________
SECTION VII FIRST AID MEASURES
___________________________________________________________
EMERGENCY FIRST AID PROCEDURES
INGESTION: Do not induce vomiting. Administer large amounts of milk and call a
physician.
INHALATION: Remove to fresh air and consult with a physician if symptoms persist.
SKIN CONTACT: Promptly wash area with soap and water, and rinse thoroughly. Remove
contaminated clothing.
EYE CONTACT: Promptly flush eyes with large amounts of fresh water for at leas 15
minutes. Contact a physician immediately.
____________________________________________________________________________
SECTION VIII REGULATORY INFORMATION
___________________________________________________________
SUPERFUND AMENDMENT AND REAUTHORIZATION ACT OF 1986 (SARA TITLE III)
SECTION 302- EXTREMELY HAZARDOUS SUBSTANCES (40 CFR 355): This product does
not contain materials listed in Appendix A and B as an Extremely Hazardous Substance.
SECTION 311/312- MATERIAL SAFETY DATA SHEET REQUIREMENTS (40 CFR 370):
Materials listed in 29 CFR 1910, Subpart Z is identified in Section IV. None are known or
suspected carcinogens listed by the National Toxicology Program, International Agency of
Research on Cancer, or OSHA.
SECTION 313- LIST OF TOXIC CHEMICALS (40 CFR 372): Listed materials contained in this
product are identified in Sections II or IV of this MSDS.
TOXIC SUBSTANCES CONTROL ACT (TSCA)
Not available
CLEAN AIR ACT AMENDMENT OF 1990
This product does not contain, and has not contacted during manufacture, any Ozone depleting
Substances.
____________________________________________________________________________
SECTION IX FIRE AND EXPLOSION HAZARD DATA
____________________________________________________________
FLASH POINT: Greater than 200 F
AUTOIGNITION TEMPERATURE: N/A
EXTINGUISHING MEDIA: Water mist, Foam, CO2, dry chemical.
FLAMMABLE LIMITS: LOWER: Not Applicable
UPPER: Not Applicable
SPECIAL FIREFIGHTING PROCEDURES: Toxic gasses may be released. Use self-contained
breathing apparatus.
UNUSUAL FIRE/EXPLOSIVE HAZARDOUS: None.
MATERIAL SAFETY DATA SHEET Page 4 of 4
___________________________________________________________
SECTION X HAZARD RATING INFORMATION
____________________________________________________________
HMIS HAZARD RATING:
4= EXTREME TOXICITY= 1
3= HIGH FIRE= 0
2= MODERATE REACTIVITY= 0
1= SLIGHT SPECIAL= G
0= INSIGNIFICANT
____________________________________________________________________________
SECTION XI REACTIVITY DATA
____________________________________________________________
STABILITY: Stable
CONDITIONS TO AVOID: Temperatures of 212F or over will cause boiling of water.
INCOMPATIBILITY: Treat as water.
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition on burning may
produce toxic gasses.
____________________________________________________________________________
SECTION XII USER'S RESPONSIBILITY
Target Coatings cannot anticipate all conditions of handling and use of this product.
Therefore, Target Coatings accepts no responsibility for results obtained by application of this
information, or safety and suitability of our products either alone or in combination with other
products. It is the responsibility of the user to provide a safe workplace, using the health and
safety information contained herein as a guide. Target Coatings will accept no liability for
damages or loss incurred from the improper handling and us of this product.
____________________________________________________________________________
SECTION XIII SPECIAL PRECAUTIONS
PRECAUTION: READ MSDS BEFORE USE
___________________________________________________________________________
SECTION XIV PREPARATION INFORMATION
This Material Safety Data Sheet was prepared by:
Jeff Weiss Telephone Number: 1-800-752-9922
|