MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 1 of 5
Hazmat Sorbents Revision Date: 02/20/08
MSDS No. 1003
Section 1. Chemical Product and Company Identification
Product Number: S2 Series
Product Name: HAZMAT Sorbent Products
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-
F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
9003-07-0 Polypropylene Particulate or Fabric 98.7%
---NA--- Yellow Pigment 0.3%
---NA--- Surfactant 1.0%
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency Overview
Odorless, white or colored fabric or particulate. This material presents little or
no hazard if spilled and exhibits no unusual fire hazard.
Potential Health Effects
Eye: Direct contact may cause irritation.
Inhalation: Exposure to dust levels exceeding the PEL (see Section 8) may cause irritation of the
upper respiratory system. Breathing dust may aggravate acute or chronic asthma or
other chronic pulmonary diseases.
Signs and Symptoms:
?Eyes: Redness, Tearing
?Inhalation: Dry cough, labored breathing during exertion
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Brush off excess fibers with dry towel. Wash affected area with plenty of soap and water for several
minutes. If skin irritation develops or persists, seek medical attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
NOTE: If burned through contact with molten material, cool as quickly as possible with water and seek
medical attention. Do not attempt to remove the cooled molten material.
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 2 of 5
Hazmat Sorbents Revision Date: 02/20/08
MSDS No. 1003
Section 5. Fire Fighting Measures
Flash Point: >625 癋
Flammable Limits: NA
Auto-ignition Temperature: >675 癋
NOTE: This material will burn, but it is difficult to ignite.
Extinguishing Media: Water spray, ABC dry chemical, foam, or carbon dioxide. Use water fog or
spray to cool exposed equipment and containers.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be
used. Thermal decomposition of this product may produces hazardous
and irritating gases. See Section 10.
Section 6. Accidental Release Measures
Unused material can be shoveled, swept, or vacuumed and recycled for use. Avoid generating airborne dust.
If used material is released or spilled, see Section 13.
Section 7. Handling and Storage
Store at room temperature in a dry area. When handling, avoid the generation of airborne dust. Storage for
extended periods (>30 days) at temperatures >150 癋 may cause decomposition. This material produces an
electrostatic accumulation hazard. Use proper grounding/bonding procedures.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically developed for this product; treated as a nuisance dust as defined in
29 CFR 1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV is 10 mg/M3.
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR
1910.132--Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
?Eyes: Safety glasses or goggles
?Skin: Work gloves
Adequate ventilation should be provided to limit the amount of airborne dust.
Section 9. Physical and Chemical Properties
Appearance: White or colored fabric or particulate
Odor: Odorless Evaporation Rate (Butyl Acetate=1): NA
Boiling Point: NA % Vaporizable by volume (H2O=100): <0.4
Vapor Pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Insoluble
Specific Gravity (H2O=1): 0.90
Melting Point: >320 癋
pH: NA
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 3 of 5
Hazmat Sorbents Revision Date: 02/20/08
MSDS No. 1003
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: See Section 7
Incompatibility (Materials to Avoid): Avoid contact with hot or concentrated nitric and perchloric acids,
and fuming sulfuric acid at temperatures >140 癋
Hazardous Decomposition or Byproducts: Thermal decomposition produces carbon monoxide, carbon
dioxide, methane, acetone, and other ketones.
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by RCRA (40 CFR 261). Once used, this
product will take on the characteristics of the chemical sorbed and should be disposed of accordingly.
Disposal of this product (used or unused) must be in compliance with all local, state, and federal regulations.
Section 14. Transport Information
This product is not a DOT Hazardous Material and is not regulated for all shipping purposes.
Section 15. Regulatory Information
This product does not meet the definition of a hazardous chemical given in 29 CFR 1910.1200 (OSHA).
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazard Classification:
Immediate (acute): No
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA--Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/Int'l Right-to-Know Regulations: Not listed
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 4 of 5
Hazmat Sorbents Revision Date: 02/20/08
MSDS No. 1003
Abbreviations (cont.):
IARC: International Agency for Research on Cancer
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United States Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation, and Liability Act
DOT: Department of Transportation
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA Ratings: HMIS Ratings:
Health: 0 Health: 0
Fire: 1 Flammability: 1
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: NA
NOTE: This MSDS has been prepared only for the Hazmat Sorbent Products (S2 Series) of SPILFYTER?Products.
The MSDS's of the chemicals used with this product must be reviewed completely, and precautions taken as
described.
The information accumulated herein has been compiled from sources believed to be reliable and is accurate to the
best of our knowledge. However, NPS Corporation cannot give guarantees regarding the information from sources,
and expressly does not make any warranties, nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER?products from NPS Corporation
You have been provided data, product labels, MSDS's, and other information about SPILFYTER?Products.
Some SPILFYTER?Products are hazardous. Information about SPILFYTER?Products that are hazardous is
furnished without guarantee. NPS Corporation does not guarantee the accuracy of the information about hazardous
SPILFYTER?Products.
Those products are only to be used by people having expertise in using the hazardous products.
The information provided about the hazardous products is believed to be correct. You must perform your
investigation as to the safety, toxicity, suitability, and proper shipping method for any hazardous SPILFYTER?br>
Product.
No guarantee, expressed or implied, is made by NPS Corporation about the results of use of its products. No
guarantee is made as to the safety and toxicity of any SPILFYTER?Product.
NPS Corporation does not assume any liability arising out of use of SPILFYTER?Products. Additional information
and research may be necessary before you use the SPILFYTER?Products. NPS Corporation is not responsible for
damages, direct or indirect, resulting from the use of SPILFYTER?Products or from reliance on data in the MSDS
or product label.
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 5 of 5
Hazmat Sorbents Revision Date: 02/20/08
MSDS No. 1003
If you resell SPILFYTER?Products, you must, by law, furnish your customers a copy of MSDS's and handling
instructions.
You are also required by law to insure that all SPILFYTER?Products are properly shipped.
SPILFYTER? KOLLECT-A-KEM? HANDS-IN-BAG? KOLORSAFE? and GRAB&GO?are all registered
trademarks of NPS Corporation
AQUALOCKITTM, TRUK-KIT TM, DRAINGUARDTM, GAPSEALTM, MEDICLEANTM, and TIDYMATTM, are all
trademarks of NPS Corporation
?Copyright 2002, NPS Corporation
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 1 of 5
KOLORSAFE?Liquid Acid Neutralizer Revision Date: 02/20/08
MSDS No. 1006
Section 1. Chemical Product and Company Identification
Product Number: 4100 Series
Product Name: KOLORSAFE?Liquid Acid Neutralizer
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
102-71-6 Triethanolamine
72-48-0 Alizarin
7732-18-5 Water
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency Overview
Purple liquid with an ammonia-like odor. This product presents no unusual
fire hazard.
Potential Health Effects
Eye: May cause slight to severe irritation.
Skin: May cause slight to severe irritation. Repeated skin contact may aggravate an existing
dermatitis (skin condition) and/or sensitivity of the skin.
Inhalation: Exposure to vapors or mists in excess of the TLV (see Section 8) or in unusually high
concentrations generated from spraying, heating the material, or from exposure in poorly
ventilated areas or confined spaces may cause irritation of the nose, throat, and upper
respiratory system.
Signs and Symptoms:
?Eyes: Redness, Tearing
?Skin: Redness, Swelling
?Inhalation: Discomfort of the nose and throat, headache, nausea, and drowsiness
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Remove contaminated clothing. Wash affected area with plenty of soap and water for
several minutes. If skin irritation develops or persists, seek medical attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
Ingestion: If swallowed, call a physician or poison control center immediately.
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 2 of 5
KOLORSAFE?Liquid Acid Neutralizer Revision Date: 02/20/08
MSDS No. 1006
Section 5. Fire Fighting Measures
Flash Point: Not Tested
Flammable Limits: Not Tested
Auto-ignition Temperature: Not Tested
NOTE: This material is non-flammable as supplied.
Extinguishing Media: Water spray, ABC dry chemical, foam, or carbon dioxide. Use water fog or spray
to cool exposed equipment and containers. Water or foam may cause frothing.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be
used. Thermal decomposition of this product may produce hazardous or
irritating byproducts. See Section 10.
Section 6. Accidental Release Measures
Avoid breathing vapors. Avoid contact with skin, eyes, or clothing. Contain the spill and collect the material
using chemically resistant sorbent products. If this product is mixed with other materials, see Section 13.
Section 7. Handling and Storage
Avoid high heat and/or freezing conditions. Keep container tightly closed. Suitable for general chemical
storage under normal warehouse conditions.
NOTE: If this product is stored at temperatures >150 癋 or at elevations above 5000 feet, gas may form,
increasing the pressure within the container, causing the container to bulge. If bulging occurs, remove the
container from the work area and slowly open the container to release the gas. Be sure to wear proper
personal protective equipment.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: Triethanolamine
ACGIH TLV is 5 mg/M3.
OSHA PEL: Not Established
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR
1910.132--Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
?Eyes: Safety glasses, goggles, or face shield
?Skin: Suitable chemically resistant gloves and protective clothing
?Inhalation: Air purifying respirator with appropriate chemical cartridge or canister
Adequate ventilation should be provided to meet the ACGIH exposure limits.
Section 9. Physical and Chemical Properties
Appearance: Purple liquid
Odor: Ammonia-like odor Evaporation Rate (Butyl Acetate=1): Not Tested
Boiling Point: 218 癋 % Vaporizable by volume (H2O=100): 100
Vapor Pressure (mmHg): Not Tested
Vapor Density: Not Tested
Solubility in Water: Soluble
Specific Gravity (H2O=1): 1.09
Freezing Point: -4 癋
pH: 10.2
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 3 of 5
KOLORSAFE?Liquid Acid Neutralizer Revision Date: 02/20/08
MSDS No. 1006
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: See Section 7
Incompatibility (Materials to Avoid): None known
Hazardous Decomposition or Byproducts: In a limited air supply, thermal decomposition produces carbon
monoxide, carbon dioxide, ammonia, irritating aldehydes and
ketones.
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by RCRA (40 CFR 261). Once used, this
product may take on the characteristics of the chemical(s) it was used with and should be disposed of
accordingly. Disposal of this product (used or unused) must be in compliance with all local, state, and federal
regulations.
Section 14. Transport Information
Not regulated by DOT
Section 15. Regulatory Information
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazard Classification:
Immediate (acute): Yes
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA--Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/Int'l Right-to-Know Regulations: Canada's WHMIS--Triethanolamine 1%
California Proposition 65: Not listed
International Regulations: All components are listed on the following lists:
?Canada Inventory Status: Canadian Domestic Substance (DSL)
?European Inventory of Existing Chemical Substances (EINECS)
?Japan Inventory Status: Japanese MITI Inventory
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 4 of 5
KOLORSAFE?Liquid Acid Neutralizer Revision Date: 02/20/08
MSDS No. 1006
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
IARC: International Agency for Research on Cancer
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United States Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation, and Liability Act
DOT: Department of Transportation
WHMIS: Workplace Hazardous Materials Information System
n.o.s.: Not Otherwise Specified
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA Ratings: HMIS Ratings:
Health: 1 Health: 1
Fire: 1 Flammability: 1
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: X
NOTE: This MSDS has been prepared only for the KOLORESAFE?Liquid Acid Neutralizer (4100 Series) of
SPILFYTER?Products. The MSDS's of the chemicals used with this product must be reviewed completely, and
precautions taken as described.
The information accumulated herein has been compiled from sources believed to be reliable and is accurate to the
best of our knowledge. However, NPS Corporation cannot give guarantees regarding the information from sources,
and expressly does not make any warranties, nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER?products from NPS Corporation
You have been provided data, product labels, MSDS's, and other information about SPILFYTER?Products.
Some SPILFYTER?Products are hazardous. Information about SPILFYTER?Products that are hazardous is
furnished without guarantee. NPS Corporation does not guarantee the accuracy of the information about hazardous
SPILFYTER?Products.
Those products are only to be used by people having expertise in using the hazardous products.
MATERIAL SAFETY DATA SHEET
SPILFYTER?Products Page 5 of 5
KOLORSAFE?Liquid Acid Neutralizer Revision Date: 02/20/08
MSDS No. 1006
The information provided about the hazardous products is believed to be correct. You must perform your
investigation as to the safety, toxicity, suitability, and proper shipping method for any hazardous SPILFYTER?br>
Product.
No guarantee, expressed or implied, is made by NPS Corporation about the results of use of its products. No
guarantee is made as to the safety and toxicity of any SPILFYTER?Product.
NPS Corporation does not assume any liability arising out of use of SPILFYTER?Products. Additional information
and research may be necessary before you use the SPILFYTER?Products. NPS Corporation is not responsible for
damages, direct or indirect, resulting from the use of SPILFYTER?Products or from reliance on data in the MSDS
or product label.
If you resell SPILFYTER?Products, you must, by law, furnish your customers a copy of MSDS's and handling
instructions.
You are also required by law to insure that all SPILFYTER?Products are properly shipped.
SPILFYTER? KOLLECT-A-KEM? HANDS-IN-BAG? KOLORSAFE? and GRAB&GO?are all registered
trademarks of NPS Corporation
AQUALOCKITTM, TRUK-KIT TM, DRAINGUARDTM, GAPSEALTM, MEDICLEANTM, and TIDYMATTM are all
trademarks of NPS Corporation
Copyright 2001, NPS Corporation
3303 Spirit Way
Green Bay, WI 54304
800-558-5066
920-983-9223
920-983-9291
www.npscorp.com
February 22, 2008
Dear Valued Customer,
In response to your request for a Material Safety Data Sheet (MSDS) on either our SPILFYTER?br>
Chemical (5700 Series) or Wastewater (5800 Series) Classifier Strips, the following information is
provided.
The SPILFYTER?Chemical and Wastewater Classifier Strips are considered to be an "article" under
29 CFR 1910.1200--OSHA Hazard Communication. An "article" is defined as being a
manufactured item: (1) which is formed to be a specific shape or design during manufacture; (2)
which has end use functions dependent in whole or in part upon its shape or design during end use;
and (3) which does not release, or otherwise result in exposure to, a hazardous chemical under
normal (intended) conditions of use.
Thank you for this opportunity to be of service to you. If you have any further questions, please
contact me at (800) 558-5066.
Sincerely,
NPS Corporation
?registered trademark NPS Corporation
|