Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 1 ?PRODUCT IDENTIFICATION
Product Name: Manufacturer's Name:
TPO Cut Edge Sealant Water Tight Technologies, LLC
Item Number: Manufacturer's Address:
TCES P.O. Box 899, Payson, AZ 85547
NFPA Acute Hazard Rating:
24 Hour Emergency Telephone Number:
Health 2, Flammability 3, Reactivity 0
CHEMTREC ?United States 800-424-9300 ;
HMIS Acute Hazard Rating:
International 202-483-7616 (collect)
Health 2, Flammability 3, Reactivity 0
Chemical Name/Synonyms: Chemical Family:
N/A Mixture
SECTION 2 ?CHEMICAL COMPOSITION
Ingredient Components (chemical names) Common Case No. OSHA ACGIH
Names PEL-TWA TLV-TWA
%
Hazardous components 1% or greater
Carcinogens 0.1% or greater
Stoddard Solvent 10 - 30 8052-41-3 500 ppm 100 ppm
Xylene 10 - 30 1330-20-7 100 ppm 100 ppm
Ethyl Benzene 5-10 100-41-4 100 ppm 100 ppm
Toluene 0.1 ?1 108-88-3 200 ppm 20 ppm
(300 ppm ceiling)
SECTION 3 ?PHYSICAL & CHEMICAL CHARACTERISTICS
Physical State:
Appearance/Odor: Solubility in Water:
Liquid N/A
Off-white liquid with slight odor
Boiling Point: Specific Gravity (H睴=1) Melting Point:
0.7 N/A
212?F
Vapor Pressure: Additional Information: Freezing Point:
N/A VOC= 464 g/L Not Established
Volatiles: (% Wt or % Vol) Ignition Temperature: Reactivity in Water:
55% N/A
N/A
Vapor Density (Air=1) Evaporation Rate:
Slower than diethyl ether
Heavier than air
BRITE-n-EZTM TPO Cut Edge Sealant ?Page 1 of 1
March 15, 2008
Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 4- FIRE & EXPLOSION HAZARD DATA
Flash Point: Flammable Limits (in air):
79?F LEL: N/A UEL: N/A
Extinguishing Media: Fire Fighting Procedures:
NFPA Class B fire extinguishers, Alcohol Foam, CO2, Firefighters should wear self-contained breathing
Dry Chemical. Polymer foam preferred for large fires. apparatus. Water may be ineffective, but may be used to
cool exposed containers to prevent pressure build-up.
And possible auto-ignition or explosion when exposed to
extreme heat. Fog nozzles are preferable.
Special Fire & Explosion Hazards:
Hazardous Decomposition Products:
During emergency conditions, overexposure to
Burning, including when heated by welding or cutting,
decomposition products may cause a health hazard.
will produce smoke, carbon monoxide and carbon
Symptoms may not be immediately apparent. Obtain
dioxide.
medical attention.
Method Used:
N/A
SECTION- 5 HEALTH HAZARD DATA
Signs and Symptoms of Exposure:
Permissible Exposure Limit:
Can cause eye irritation, defatting of the skin,
Not Established
gastrointestinal irritation, nausea, vomiting and
Effects of Overexposure:
diarrhea. Aspiration of material into lung may cause
Pre-existing skin, respiratory, central nervous system, liver
chemical pneumonitis, which can be fatal. May cause
and kidney conditions may be susceptible.
nose or throat irritation. High vapor concentrations
may cause central nervous system depression
characterized by headaches, dizziness and nausea.
Acute: Chemical Listed as a Carcinogen (or Potential Carcinogen):
See Signs and Symptoms of Exposure
NTP: None
Chronic:
I.A.R.C.: Ethyl Benzene (CAS 100-41-4)
Can have health effects on cardiac, behavioral and central
OSHA: Ethyl Benzene (CAS 100-41-4)
nervous system as well as a general irritant. Target organs
are kidney and liver.
Emergency & First Aid Procedures:
Eye Contact:
Flush with water, continue for at least 15 minutes and call physician
Skin Contact:
Remove contaminated clothing. Immediately wash with soap and water and rinse thoroughly. Call physician of
irritation persists.
Inhalation:
Remove to fresh air. Administer oxygen or artificial respiration, if necessary. Call physician.
Ingestion:
If swallowed, do not induce vomiting unless directed by medical personnel Call physician immediately.
Primary Route of Entry:
Inhalation, ingestion, eyes & skin absorption.
BRITE-n-EZTM TPO Cut Edge Sealant ?Page 2 of 2
March 15, 2008
Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 6 ?REACTIVITY DATA
Stability: Incompatibility:
Stable at ambient temperatures and pressures. Strong acids or bases.
Hazardous Decomposition Products: Hazardous Polymerization:
Carbon monoxide and carbon dioxide.
Will not occur.
Conditions to Avoid:
Avoid excessive heat (>115?F) and sources of ignition.
SECTION 7 - SPILL OR LEAK PROCEDURES
Steps to be taken in case material is released or spilled:
Small spill:
Prevent further leakage or spillage if safe to do so. Eliminate ignition sources, provide ventilation, dike the spill area
and add absorbent materials. Place in proper containers for disposal in accordance with federal, state and local
regulations. Clean-up personnel should wear rubber gloves and respiratory protection. Do not contaminate water and
avoid subsoil penetration.
Large Spill:
Same as small spill.
Waste Disposal Method:
This product may contain traces of benzene and may be classified as a hazardous waste (waste number(s) DO 18)
under the EPA RCRA (40CFR 261.24). However this product is only classifiable as hazardous waste if it exhibits the
characteristics of toxicity as shown by the toxicity characteristic leaching procedure (TCLP). Under RCRA, it is the
responsibility of the end user of this product to determine whether it meets this criteria at the time of disposal.
SECTION 8 ?SPECIAL PROTECTION
Respiratory Protection: Eye Protection:
If spraying this material or in absence of adequate Safety glasses with side shields
ventilation, use NIOSH-Certified respiratory protection
for organic vapor.
Protective Gloves: Other Protective Equipment:
Impervious gloves are recommended to prevent skin Protective work clothing.
contact.
Ventilation:
Provide adequate ventilation to maintain airborne concentrations below OSHA PELs.
BRITE-n-EZTM TPO Cut Edge Sealant ?Page 3 of 3
March 15, 2008
Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 9 ?SPECIAL PRECAUTIONS OR OTHER COMMENTS
Storage/Handling:
Store in cool, dry, well ventilated facility at temperatures below 115?F. Store and use away from all sources of direct
heat and ignition. Protect against electrostatic charge. Keep containers closed when not in use. Do not cut, grind, weld
or drill on or near this container.
Other Precautions:
Provide adequate ventilation and avoid prolonged or repeated contact with the skin. Wash with soap and water after
contact.
Work/Hygienic Practices:
Maintain good personal hygiene practices. Do not eat, drink, or smoke in work areas. Wash exposed skin before
eating, drinking, smoking, or applying cosmetics.
SECTION 10 - TRANSPORTATION
Regulatory Agency: Identification Number:
U.S.A., DOT, IMO UN 1133
Labels Required:
Proper Shipping Name:
Adhesives, flammable Flammable Liquid
Hazard Classification: Other Requirements:
SARA reportable ingredients ?Ethyl benzene (CAS 100-41-4)
3
and Xylene (CAS 1330-20-7)
DOT Reportable Qty ?Xylene (CAS 330-20-7) is 100 lbs and
Ethyl benzene (CAS 100-41-4) is 1,000 lbs.
Packing Group:
III
SECTION 11 ?MISCELLANEOUS INFORMATION
Additional Comments:
This product contains a chemical known to the State of California to cause cancer and birth defects or other
reproductive harm.
Date of Previous MSDS:
N/A
Changes Since Previous MSDS:
N/A
Telephone Number for Additional Information:
(888) 269-2122
DISCLAIMER
The information contained herein is based on data considered accurate which has been obtained from other
companies and organizations. However, no warranty or representation is expressed or implied that the information
is accurate, complete, or representative. Water Tight Technologies, LLC assumes no responsibility for injury to the
buyer, the buyer's employees, or any third persons if reasonable safety procedures are not followed.
BRITE-n-EZTM TPO Cut Edge Sealant ?Page 4 of 4
March 15, 2008
|