MATERIAL SAFETY DATA SHEET
511 Seal & Enhance
Impregnating Color Enhancer www.miraclesealants.com
Osha's Hazard Communication Standard US Dept. of Labor Ventilation:
Local exhaust- if available Special- none
Identity No: Name: 511 Seal & Enhance
Mechanical- if available Other- None
Section 1
Protective gloves: Plastic or rubber, chemical resistant
Manufacturers Name: Miracle Sealants Company Eye Protection: Tight fitting, splash, proof safety goggles.
Address: 12318 Lower Azusa Road Other protective clothing or equipment: chemical resistant clothing.
Emergency Phone: 800-350-1901
Work hygienic practices: wash hands thoroughly before handling food stuffs,
City: Arcadia
liquids or tobacco products. Use common sense and care around chemicals.
State: CA
Never mix this product with other chemicals. Consult your supervisor for all
Phone: 626-443-6433
other hygienic and safety practices. All practices depend on your specific busi-
Date Prepared: 12-2009
ness. Directions for use normally found on label which will dictate engineering
Section 2 - Hazardous Ingredient/Identity Information and control measures.
Hazardous Components CAS# OSHA PEL ACGIH TWA Section 9 - Shipping
Solvent Naphtha (Petroleum) 64742-88-7 500 ppm 100 ppm
U.S. Department of Transportation Classification (49CFR)
Medium Aliphatic
ID # UN1993
Section 3 - Physical /Chemical Characteristics Proper Shipping Name PETROLEUM DISTILLATES, N.O.S.
Boiling Point: Appx. N200?C Specific gravity (H20=1) -1.25 Class/ Division 3
Vapor pressure: Not Determined Melting point: Not Determined Packing group III
Vapor density(air=1) : Heavier than air Evaporation rate(Butyl) : ? Marine Pollutant: No
Solubility in water: None Transportation Class: 55
IMDG
Appearance and odor: Clear, Colorless to amber Liquid.
ID # UN1268
VOLATILE BY VOLUME: ?60-70%
Proper Shipping Name: PETROLEUM DISTILLATES, N.O.S.
VOC CONTENT: 591 g/L
Class/ Division 3
Section 4 - Fire and Explosion Hazard Data Packing group III
Flash point: 145?F Method: Pensky-Martens IATA (Country variations may apply)
closed cup ASTM D 93 Section 10 - Regulatory Information:
Flammable limits: Not tested
Toxic Substances Control Act (TSCA): This product and/or all the ingredients
LEL: not tested UEL: Not tested
contained in this product have been registered under the Toxic Substances
pH: Not Applicable DOT#: UN 1268
Control Act.
NFPA hazard rating- HFRS (0-Least, 4-Extreme): 2
HMIS hazard rating- HFR (0-Least, 4-Extreme): 2 SARA: No SARA 313 chemicals identified.
Extinguish media: Foam, water spray or fog. Dry chemical powder, CO2, sand or Section 302 - Extremely Hazardous Substances:
earth may be used for small fires only. Do not discharge extinguishing waters
None.
into the aquatic environment.
Section 304 - CERCLA Hazardous Substances:
Special fire fighting procedures: wear full protective clothing and self-contained
Cas # Appx. Wt. % Component name
breathing apparatus.
1330-20-7 4.5 Xylene
Unusual fire and explosion hazards: none
100-41-4 1.3 Ethylbenzene
Section 5 - Reactivity Data 108-88-3 Trace Toluene
Stability: Conditions to avoid: extreme heat and open flames Section 312 - Hazard Class:
Hazardous Combustion products:
Acute: Yes Chronic: Yes Fire: Yes
Burning can produce the following combustion products: Pressure: No Reactive: No
Oxides of carbon Oxides of nitrogen
Section 313 - Toxic Chemicals:
Oxides of silicone Traces of Hydrogen Fluoride
Cas # Appx. Wt. % Component name
Carbon monoxide is highly toxic if inhaled; carbon dioxide is sufficient concen-
1330-20-7 4.5 Xylene
trations can act as a asphyxiant. Acute overexposure to the products of combus-
100-41-4 1.3 Ethylbenzene
tion may result in irritation of the respiratory tract.
Supplemental State Compliance Information
Section 6 - Health Hazard Data
California:
Harmful or fatal if swallowed Warning: This product contains the following chemical(s) listed by
Causes eye and skin irritation the state of California under the Safe Drinking Water and Toxic Enforcement Act
Harmful if swallowed of 1986 (Proposition 65) as being known to cause cancer, birth defects or other
Harmful if inhaled reproductive harm.
Harmful if absorbed through skin
Cas # Appx. Wt. % Component name
Aspiration may cause lung damage
108-88-3 Trace Toluene
May cause allergic skin reaction
Massachusetts:
May cause dizziness and drowsiness
Cas # Appx. Wt. % Component name
May cause liver and kidney disorders
1330-20-7 4.5 Xylene
Medical conditions generally aggravated by exposure- same as signs and
100-41-4 1.3 Ethylbenzene
symptoms of over exposure.
New Jersey:
Emergency and First Aid Procedures:
Cas # Appx. Wt. % Component name
Eyes: Flush with water for 15 minutes. If irritation persists call a physician.
1330-20-7 4.5 Xylene
Skin: wash off with soap and clean water for 15 minutes. If irritation persists call
100-41-4 1.3 Ethylbenzene
a physician.
68988-56-7 4-8 Trimethylated silica
Ingestion: Drink large amounts of water. Call Physician
3555-47-3 Trace Tetra(trimethoxysiloxy) silane
Inhalation: Remove person to fresh air. If not breathing, administer artificial res-
piration including oxygen. Provide medical attention. Pennsylvania:
Section 7 - Precautions for safe handling and use Cas # Appx. Wt. % Component name
68988-56-7 4-8 Trimethylated silica
Steps to be taken in case material is released or spilled: soak up with inert
1330-20-7 4.5 Xylene
absorbent material.
EPA Hazard Waste: Not Available
Scoop up and place in a proper waste disposal container.
Waste disposal method: Dispose of in accordance with state and local NOTE: Miracle Sealants believes the data set forth are accurate. Miracle
regulations. Sealants makes no warranty with respects thereto and disclaims all
liability or reliance thereon. Such data are offered solely for consideration,
Precautions to be taken in handling and storing: store in a cool, dry place, out of
investigation and verification. Also, the data set forth is for the concentrated
direct sunlight.
finished product. All lab samples are for experimental purposes only and
Do not freeze less than or equal to 32?F or heat above 110?F.
used at the customers discretion.
Other precautions: KEEP OUT OF REACH OF CHILDREN. Follow directions on the
container for proper use of this product.
Section 8 - Control Measures
Respiratory protection: Ventilate by opening all doors and windows. If exposure
above the TLV or PEL require a NIOSH approved respirator equipped for the
exposure or suitable respiratory protection per 29 CFR 1910.134 is required.
12-2009
PRODUCT INSTRUCTIONS
511 Seal & Enhance
Impregnating Color Enhancer www.miraclesealants.com
Ready to Use "One Step" Solvent Base Penetrating/Color Enhancer for 7. Any excess product residue that may dry on the surface can be
All Honed, Textured and Polished Stone & Tile Surfaces Including: removed by reapplying product and wiping excess off immediately
while wet, with a white terry cloth towel. Allow to cure 6 - 12 hours
I Granite I Marble I Natural Stone
before grouting.
I Slate I Limestone I Quarry Tile
I Grout I Not for Concrete/Masonry 8. Proceed with the grouting process per the manufacturer's instructions.
Special Features 9. Clean all excess grout completely from the surface with a clean sponge
I Superior Stain Protection I Superior Color Enhancement and water. Take the time at this stage of the installation to carefully
I Oil Resistant I Water Resistant clean and detail.
I One Product, One Step I Durable
10. Allow grout joints to dry per manufacturers specification.
I Easy-to-Use I Grout Release
11. If grout clean up is not performed effectively, additional cleaning may
I Interior & Exterior Applications I Non Yellowing
be necessary.
I Color Enhancing Grout Sealer
I Revives Color to Washed Out Grout Grout Sealing
Once the grout has cured per the manufacturers recommendations,
Product Description
proceed with the sealing of the grout.
KEEP OUT OF REACH OF CHILDREN. 511 Seal & Enhance is a unique, one-
step formula designed for maximum stain protection and superior color Directions
enhancement. It will enhance the color of tumbled, honed, acid-washed, 1. Insure that the surface is clean, dry and free from contaminants.
saandblasted, flamed, textured and polished natural stone, brick, grout &
2. Liberally apply an even application of 511 Seal & Enhance using a
clay pavers. 511 Seal & Enhance can also be used on new installations as a
Miracle Sealants' Mira Brush, clean white towel or a natural fiber paint
grout release before the grouting process.
brush directly to untreated grout joints.
Sample Testing
3. Allow 511 Seal & Enhance to penetrate the surface for 3 - 5 minutes
Due to variations between substrates, sample testing is recommended to
before removing all excess productwith a clean towel.
assure maximum performance and suitability for the inteded use. Once
12. A 2nd application is necessary and should be applied after the first has
enhanced, stone cannot be restored to its original color. Users must deter-
dried at least 1 hour.
mine the suitability of the product for their intended use.
13. Any excess product residue that may dry on the surface can be
N E W I N STA L L AT I O N S removed by reapplying product and wiping excess off immediately
while wet, with a white terry cloth towel. Allow to cure 6 - 12 hours
Read entire label and PDS/MSDS before using. 511 Seal & Enhance
before grouting.
should not be diluted or thinned in any way. 511 Seal & Enhance should be
used as directed from approved container. Finished area should be allowed to cure for 12 - 24 hours before putting into
service. For optimum results keep area dry and free from stains for 72
Follow the recommended installation methods and procedures of the
hours after application.
Marble Institute of America, Building Stone Institute and the Tile Council of
America. Allow new setting materials and grout to cure per manufacturers
instructions prior to sealing. E X I ST I N G I N STA L L AT I O N S
Surface must be dry and free of contaminants including previously applied
Sealing as a Grout Release
sealers, coatings, waxes, dirt, lime & hard water deposits, efflorescence,
To insure the best possible installation, 511 Seal & Enhance should be
rust and other heavy dirt and grime.
applied as a grout release before the grouting process. 511 Seal & Enhance
will resist dye absorption, facilitate grout residue removal (up to 45% Floor Finish Removal
faster), and offer superior stain resistance during and after the construction To remove existing floor finish and/or waxes use Mira Strip for solvent base
process. finish and H2O Strip for water base finish as directed.
Directions Heavy Duty Cleaning
1. Protect neighboring and adjacent surfaces including baseboards, wood, To remove lime, hard water deposits, efflorescence rust and other heavy
carpet, metal and landscaping. dirt and grime use GCFR (Grout, Concrete Film Remover) "Stronger" or
Phosphoric Acid Cleaner "Mild-Strong" as directed. These acid cleaners
2. Sweep or vacuum all dust, dirt and surface debris.
can affect the surface finish of acid sensitive stone and tile. For acid
3. Insure the surface is clean, dry and free from contaminants.
sensitive stone or tile use Liquid Poultice as directed.
4. Liberally apply an even application of 511 Seal & Enhance using a
Miracle Sealants' Mira Brush, clean white towel or natural fiber paint
brush. Be careful not to allow sealants into open un-grouted joints.
5. Allow 511 Seal & Enhance to penetrate the surface for 3 - 5 minutes
before removing all excess product before it dries on the surface with a
clean towel.
6. A 2nd application is necessary and should be applied after the first has
dried at least 1 hour.
www.miraclesealants.com
Light Cleaning Additional Products
For light cleaning use Mira Clean #1 as directed. Miracle Sealants Company offers a complete line of water & stain
repellents, sealers, cleaners, polishing compounds, diamond abrasives,
Sealing (Surface & Grout)
machinery and accessories for the tile, stone, concrete, metal, fabric and
Follow the application instructions previously mentioned, except now seal
carpet professional or do-it-yourself specialist.
grout joints at the same time as the rest of the stone or tile surface. When
Warranty
treating the surface and grout at the same time make sure to saturate the
grout with 511 Seal & Enhance. Do not allow 511 Seal & Enhance to puddle Instructions are a condensed guide and should not be considered
on the surface. complete. In the event of failure, the only obligation of Miracle Sealants
Company shall be to replace such products proven defective. Before using,
Coverage
user shall determine the suitability of the product for their intended use.
Coverage will vary depending on density, porosity, texture, surface absorp-
User assumes all risks and liability whatsoever in connection therein.
tion, weather, time solution is left on the surface and application methods.
Neither seller nor manufacturer shall be liable for any injury or inability to
Used as directed, 511 Seal & Enhance will cover approximately 250 - 2,000
use this product.
square feet per gallon (25 - 200 square meters per 3.785 liters).
Caution
511 Seal & Enhance contains combustible petroleum distillates. All solvents
RESEALING
must be considered toxic and must be used in a well-ventilated area. Good
Resealing will vary depending on porosity, density, hardness, foot traffic and
ventilation means that fresh air is flowing in such a way as to feel a slight
the elements (indoor or outdoor) the area is exposed to. As a general rule,
breeze. Open windows and use fans to circulate air. Continue to ventilate
medium to dense surfaces exposed to heavy foot traffic can be resealed
until vapors are eliminated. Exposure to high vapor concentration must be
every 1 - 3 years. Very hard surfaces exposed to heavy foot traffic can be
avoided. Inhaling the vapors can be harmful. Keep away from heat and
resealed every 3 - 5 years. It is important to remember that any additional
open flames. Avoid prolonged contact with skin. Gloves should be worn at
or future applications of 511 Sealants will require approximately half the
all times. Keep small children and pets out of the area until product or sur-
amount of sealant as originally used.
face has thoroughly dried. Refer to the MSDS for additional information.
Storage
Store 511 Seal & Enhance in the original container, properly sealed to avoid
contamination and evaporation. When store in the upright position at 77?F
(40?C), 511 Seal & Enhance will have a shelf life of 12 months. Do not allow
to freeze.
Technical Support
For additional technical support, contact Miracle Sealants Company @
1-800-350-1901 or 626-443-6433 ext. 3013.
Monday ?Friday from 6:30 am ?5:00 pm PT.
Office Hours
Monday ?Friday from 8:30 am ?5:00 pm PT.
1-626-443-6433 ?1-800-350-1901 Fax: 1-626-443-1435
Website
www.miraclesealants.com
Product Damage
If product is damaged during transportation contact
Info Trac @ 1-800-535-5053
12-2009
|