MATERIAL SAFETY DATA SHEET
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
CHS Inc. Transportation Emergency (CHEMTREC): 1-800-424-9300
P.O. Box 64089 Technical Information: 1-651-355-8443
Mail station 525 MSDS Information: 1-651-355-8438
St. Paul, MN 55164-0089
PRODUCT NAME: HD Moly Extreme Grease MSDS: 0203-L04AXX ?Rev. A (08/01/07)
COMMON NAME: Grease CHEMICAL FORMULA: Mixture
CHEMICAL NAME: Soap-thickened oil lubricant CHEMICAL FAMILY: Hydrocarbon
Section 2 - COMPOSITION AND INFORMATION ON INGREDIENTS
INGREDIENTS PERCENTAGES PEL (OSHA) TLV (ACGIH) CAS #
(by weight)
Oil, Severely Hydrotreated Naphthenic 30-50% N/A TWA (Oil Mist) 64742-52-5
5 mg/m3
Distillates, Petroleum, Heavy 10-30% N/A TWA (Oil Mist) Mixture
5 mg/m3
Overbased Calcium Sulfonate Complex Thickener 30-50% N/A 2 mg/m3 TWA Proprietary
*Molybdenum Sulfide 3-7% N/A 1317-33-5
*Benzenesulfonic Acid, Dodecyl, Calcium Salt 1-3% N/A 26264-06-2
Performance Additives Proprietary N/A TWA N/A
N/A
(TWA) - Time Weighted Average is the employee's average airborne exposure in any 8-hour work shift of a 40-hour work week which shall not be exceeded.
(STEL) - Short Term Exposure Limit is the employee's 15-minute time weighted average exposure which shall not be exceeded at any time during a work day unless another time limit
is specified.
* These chemicals are hazardous according to OSHA/WHIMIS criteria
Section 3 - HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
POTENTIAL HEALTH EFFECTS
ROUTES OF ENTRY: (Eye Contact, Dermal, Inhalation, Ingestion.)
ACUTE EFFECTS OF OVER EXPOSURE:
Eyes - Contact with eyes may cause irritation.
Skin - Contact with skin may cause irritation.
Inhalation - May cause irritation of the nose and throat when heated; inhalation hazard at room temperature is unlikely
due to the low volatility of this product.
Ingestion - May cause nausea and vomiting. Large quantities may affect the central nervous system.
CHRONIC EFFECTS OF OVER EXPOSURE: No adverse effects anticipated.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Existing dermatitis and respiratory conditions.
CARCINOGENICITY: NTP: No IARC: No OSHA: No
Page 1 of 4
HD Moly Extreme Grease
Section 4 - FIRST AID MEASURES
EMERGENCY AND FIRST AID PROCEDURES:
Eye Contact - If material comes in contact with the eyes, immediately wash the eyes with large amounts of water for fifteen
minutes, occasionally lifting the lower and upper lids. Get medical attention.
Skin Contact - If the material comes in contact with the skin, wash the contaminated skin with soap and water promptly. If the
material penetrates through clothing, remove the clothing and wash the skin with soap and water promptly. If irritation persists
after washing, get medical attention immediately.
Inhalation - If person breathes in large amounts of material, move the exposed person to fresh air at once. If breathing has
stopped, perform artificial respiration. Keep the person warm and at rest. Get medical attention as soon as possible.
Ingestion - If material has been swallowed, do not induce vomiting. Get medical attention immediately.
Section 5 - FIRE - FIGHTING MEASURES
FLASH POINT: 450癋 (232癈)/COC AUTO IGNITION TEMP: N/A
FLAMMABLE LIMITS IN AIR LOWER UPPER
% BY VOLUME 0.9 7.0
EXTINGUISHING MEDIA: Use water spray to cool fire exposed surfaces and to protect personnel. Use foam, dry chemical or water
spray (fog) to extinguish fire.
SPECIAL FIRE FIGHTING PROCEDURES: When fighting fires wear full turnout gear and self-contained breathing apparatus.
Water may cause splattering. Material floats on water.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Toxic fumes gases or vapors may evolve on burning.
HAZARD RATINGS: NFPA 704: Health- 1 Fire- 1 Reactivity- 0
HMIS: Health- ___ Fire- ___ Reactivity-___
Section 6 - ACCIDENTAL RELEASE MEASURES
STEPS TO TAKE IF MATERIAL IS RELEASED OR SPILLED: Minimize skin contact. Personal protective equipment should be
worn. Ventilate area if confined or poorly ventilated. Contain with dikes or absorbent to prevent migration to sewers/streams. Take up
small spill with dry chemical absorbent; large spills may require pump or vacuum prior to absorbent. May require excavation of severely
contaminated soil. Avoid contact with skin and eyes.
Section 7 - HANDLING AND STORAGE
HANDLING AND STORING: Store in closed container away from all ignition sources. Handling temperatures should not exceed
175癋 (80癈). Wash thoroughly after handling. Store in cool and well ventilated area. Odorous and toxic fumes may form from the
decomposition of this product if stored at excessive temperatures for extended periods of time."
Page 2 of 4
HD Moly Extreme Grease
Section 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
ENGINEERING CONTROLS: Ventilate to control mists and vapors below exposure limits.
RESPIRATORY EQUIPMENT: Normally not required, if exposure limits are exceeded use a NIOSH approved organic vapor
respirator. Self-contained breathing apparatus is recommended for entry into confined spaces or other poorly ventilated areas and for
large spill clean-up sites.
EYE PROTECTION: Chemical goggles or face shield recommended to minimize eye contact.
PROTECTIVE CLOTHING: Impervious (nitrile) gloves recommended when handling material to minimize exposure. Long sleeve
shirts, chemically protective aprons and chemically protective boots are recommended for contact exposure or spill clean-up. Do not wear
watches, rings or similar apparel that could entrap the material next to the skin.
OTHER (SAFETY SHOWERS, EYE WASH STATIONS, ETC.): Water should be available for flushing and washing when
exposure exists. Launder soiled clothes. Discard shoes or other leather articles saturated with the material.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Dark grey semi-solid gel, smooth texture ODOR: Mild petroleum odor
BOILING POINT: N/D SPECIFIC GRAVITY (water=1): 0.9600
VAPOR PRESSURE: <1 mm Hg 68?F VAPOR DENSITY (air=1): >5
SOLUBLE IN WATER: Insoluble EVAPORATION RATE (ether=1): <1
Section 10 - STABILITY AND REACTIVITY
pH: N/D
STABILITY:
STABLE X (At room temperature and pressure. See handling and storage section)
UNSTABLE
INCOMPATIBILITY -
CONDITIONS TO AVOID: See handling and storage section.
MATERIALS TO AVOID: Acids, oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Smoke, carbon monoxide, aldehydes, hydrogen sulfide and alkyl mercaptans may
be released. Under combustion conditions, oxides of the following elements will be formed: nitrogen, sulfur, carbon, lithium.
HAZARDOUS POLYMERIZATION: Will not occur.
Section 11 - TOXICOLOGY INFORMATION
Note: CHS has not conducted specific toxicity tests on this product.
Section 12 - ECOLOGICAL INFORMATION
Note: CHS has not conducted specific ecological tests on this product.
Page 3 of 4
HD Moly Extreme Grease
Section 13 - DISPOSAL CONSIDERATION
WASTE DISPOSAL PROCEDURES: Place contaminated materials in a disposable container and dispose of in accordance with Local,
State and Federal environmental regulations.
Section 14 - TRANSPORTATION
DOT PROPER SHIPPING NAME: N/A DOT HAZARD CLASS: N/A
DOT IDENTIFICATION NUMBER: N/A DOT EMER. RESPONSE GUIDE NO.: N/A
Section 15 - REGULATORY INFORMATION
This product does not contain toxic chemicals subject to the reporting requirements of SARA Section 313 of the Emergency Planning and
Community Right-To-Know Act of 1986 and of 40 CFR 372.
CAS Number Chemical Name Percent by Weight
SARA SECTION 311-312 HAZARD CATEGORIES (40 CFR 370.2):
FIRE: No SUDDEN RELEASE OF PRESSURE: No REACTIVE: No ACUTE: No CHRONIC: No
CA Prop 65: This product contains the following chemicals that may cause cancer or reproductive toxicity:
Naphthylamine, CAS # 134-32-7 and Naphthylamine, CAS # 91-59-8, <1ppm
Section 16 - OTHER INFORMATION
Prepared By: Hue Lam Date: August 01, 2007
Title: EHS Compliance Manager Supersedes: NA
Reason for Issue: As required
THE INFORMATION CONTAINED IN THIS MSDS RELATES ONLY TO THE SPECIFIC MATERIAL IDENTIFIED. IT DOES NOT COVER USE OF THAT
MATERIAL IN COMBINATION WITH ANY OTHER MATERIAL OR IN ANY PARTICULAR PROCESS. IN COMPLIANCE WITH 29 C.F.R. 1910.1200(g),
CHS HAS PREPARED THIS MSDS IN SEGMENTS, WITH THE INTENT THAT THOSE SEGMENTS BE READ TOGETHER AS A WHOLE WITHOUT
TEXTUAL OMISSIONS OR ALTERATIONS. CHS BELIEVES THE INFORMATION CONTAINED HEREIN TO BE ACCURATE, BUT MAKES NO
REPRESENTATION, GUARANTEE, OR WARRANTY, EXPRESS OR IMPLIED, ABOUT THE ACCURACY, RELIABILITY, OR COMPLETENESS OF THE
INFORMATION OR ABOUT THE FITNESS OF CONTENTS HEREIN FOR EITHER GENERAL OR PARTICULAR PURPOSES. PERSONS REVIEWING
THIS MSDS SHOULD MAKE THEIR OWN DETERMINATION AS TO THE MATERIAL'S SUITABILITY AND COMPLETENESS FOR USE IN THEIR
PARTICULAR APPLICATIONS.
Cenex?is a registered trademark of CHS Inc.
Page 4 of 4
|