MATERIAL SAFETY DATA SHEET
(Essentially similar to OSHA form 174, Sept. 1985 - For Compliance with OSHA鈥檚 Hazard Communication Standard, 29CFR 1910.1200)
Lead Shield庐 (5470, 5475, 5477)
Section I - Product Identity:
Manufacturer鈥檚 Name: Date of Preparation: Feb 16, 2006
Fiberlock Technologies, Inc. Information Telephone Number: (978) 623-9987
150 Dascomb Road Emergency Telephone Numbers:
Andover, MA 01810 Weekdays: (978) 623-9987
After hours, weekends & holidays:
鈥淐HEM-TEL鈥? Emergency Contact Number: (800) 255-3924
Section II - Hazardous Ingredients/Identity Information
HAZARDOUS COMMON CAS. OSHA OR ACGIH
COMPONENT NAME(S) % NO. PEL TLV
None per the limits for reporting set forth in 29CFR 1910.1200
Section III - Physical/Chemical Characteristics [See reference note(s) No. 1, 2 on Reverse]
Boiling Points of Major Constituent: 9.2
Specific Gravity (H2O=1) Wgt./gal.
212掳F
(Water)
Vapor Pressure (mm Hg) @ 68掳F Melting Point Water (Ice)
17 32掳F
Vapor Density (AIR=1)
Evaporation Rate
Heavier X Slower
(Butyl Acetate=1)
Lighter
Appearance Viscous liquid;slight Maximum VOC鈥檚
Total
Solubility in Water and Odor odor 200 g/l (1.66 lbs/gal)
Section IV - Fire and Explosion Hazard Data (Nonflammable)
Marking:
Flammable Limits: DOT Hazard Class:
Flash Point:
鈥淜eep From Freezing鈥?
LEL: N/A UEL:N/A Not Regulated
Noncombustible
Section V - Reactivity Data
Hazardous Polymerization: Will not occur.
Stability: Stable
Incompatibility: Avoid Contact with: Strong oxidizing agents (e.g., nitric acid, permanganates), etc.
Hazardous Decomposition Products: Some carbon monoxide.
Section VI - Health Hazard Data, Toxicity Data
Route(s) of Entry: N/A
Carcinogenicity?: No
Health Hazards (Acute and Chronic): N/A
EFFECTS OF OVEREXPOSURE: Inhalation: Vapors or spray mists may be slightly irritating to eye, nose, throat, and mucous membranes
of respiratory tract producing symptoms of headache, nausea in poorly ventilated areas. Skin Contact: Prolonged or repeated contact
with coating may cause slight skin irritation. Eye Contact: Direct contact; inconsequential eye irritation.
EMERGENCY AND FIRST AID PROCEDURES: Inhalation: Remove to fresh air. Eye and Skin Contact: Immediately flush eyes with plenty
of water for at least 15 minutes and consult physician; wash skin thoroughly with soap and water. If drenched, remove and wash
clothing before reuse. Ingestion: If victim is conscious, give 2 glasses of water. Call a physician.
SUPPLEMENTAL INFORMATION
To comply with New Jersey DOH Right-To-Know labeling law
(N.J.A.C. 8:59 - 5.1 & 5.2)
CAS. No.: CHEMICAL INGREDIENTS:
HMIS HAZARD RATING
7732-18-5 Water
Health 1 Flammability 0 Physical Hazard 0 Personal Protection A
57-55-6 Propylene glycol
HAZARD INDEX: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe
9004-65-3 Methyl cellulose
25265-77-4 2,2,4-Trimethyl-1,3-pentanediol PERSONAL PROTECTION CODE
monoisobutyrate A=Safety Glasses
Not Avail* Latex resin solids
*Contents partially unknown
Section VII: Precautions for Safe Handling and Use
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Keep unnecessary people away.
Floor may be slippery; use care to avoid falling. Dike and contain material with inert material (e.g. sand, earth).
Transfer liquid to containers for recovery or disposal and solid diking material to separate containers for disposal.
Keep spills and runoff out of municipal sewers and open bodies of water.
WASTE DISPOSAL METHOD: The coating and any contaminated diking material should be thoroughly air dried
and collected into drums. The drums should then be sealed and properly labeled with waste designation and
disposed of in a landfill or incinerated according to current local, state and federal regulations.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Maximum storage temperature 100掳F. Keep
closure tight and container upright to prevent leakage. Precautionary Labeling: 鈥淜eep from Freezing鈥?.
OTHER PRECAUTIONS: Do not get in eyes. Avoid skin contact. Prevent prolonged or repeated breathing of
vapors or spray mists. Do not handle until the manufacturer鈥檚 safety precautions and label instructions have
been read and understood. Avoid breathing sanding dust.
Section VIII: Control Measures
RESPIRATORY PROTECTION: None required if good ventilation is maintained. Wear respirator (MSHA/NIOSH-
approved or equivalent) suitable for concentrations and types of air contaminants encountered. Use approved
chemical/mechanical filters designed to remove particulates in open and restricted ventilation areas. Use MSHA/
NIOSH-approved airline type respirators or hood in confined areas.
VENTILATION: Sufficient ventilation, in pattern and volume, should be provided to keep the air contaminant
concentration below applicable exposure limits. All application areas should be ventilated in accordance with
OSHA regulation 29CFR Part 1910.94.
PROTECTIVE GLOVES: Impervious gloves should be worn if prolonged skin contact is likely. Use neoprene or
rubber gloves to prevent prolonged skin contact.
EYE PROTECTION: Use safety eyewear including side shields, face shields, or chemical splash goggles
(ANSIZ-87.1 or approved equivalent).
OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is
likely. Use protective cream if prolonged skin contact is likely.
HYGIENIC PRACTICES: Wash hands before eating, smoking, or using the washroom. Food or beverages
should not be consumed anywhere this product is being applied.
References:
1. Sax, N.I., 鈥淒angerous Properties of Industrial Materials鈥?, 8th ed., Van Nostrand Reinhold Company, Inc.,
NY, 1992.
2. American Conference of Governmental Industrial Hygienists, 鈥淭LV鈥檚 and Biological Exposure Indices鈥? for
the current year (published annually).
3. U.S. Code of Federal Regulations (CFR) U.S. Dept. of Labor, No. 29, Parts 1900 to 1910.1200. OSHA
Communications Standard 29 CFR 1910.1200.
4. Sax, N.I., R.J. 鈥淗azardous Chemicals Desk Reference鈥?, Van Nostrand Reinhold Co., Inc., NY, 1987.
5. Fire Protection Guide to Hazardous Materials, 12th edition, National Fire Protection Association, Quincy,
MA, 1997.
6. Title III List of Lists, U.S. Environmental Protection Agency publication EPA 560/4-90-011, January 1990.
|