MATERIAL SAFETY DATA SHEET
May be used to comply with OSHA鈥檚 Hazard Communication
HMIS HAZARD RATING
Standard 29 CFR 1910.1200. Standard must be consulted for
specific requirements.
HEALTH 0 0 = INSIGNIFICANT 3 = HIGH
FLAMMABILITY 1 1 = SLIGHT 4 = EXTREME
REACTIVITY 0 2 = MODERATE
SAFETEC OF AMERICA TRANSPORTATION INFORMATION
PROPER SHIPPING NAME Not Regulated
HAZARD CLASS / PKG. GRP. None / None REF. Not Applicable
IDENTIFICATION NUMBER None LABEL None Required
SECTION 1 - PRODUCT / COMPANY IDENTIFICATION
IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2
Petro Lock II鈩?
MANUFACTURER鈥橲 NAME EMERGENCY TELEPHONE NUMBER (24 Hours)
Safetec of America, Inc. (800) 255-3924
ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION
877 Kensington Avenue @ William l. Gaiter Pkwy. (716) 895-1822
(CITY, STATE AND ZIP CODE) DATE PREPARED September 1, 2004
SUPERSEDES March 22, 2002
Buffalo, NY 14215
SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
CAS # % (wt.) OSHA PEL/STEL ACGIH TLV/TWA/STEL
HAZARDOUS COMPONENTS
MG/M3 MG/M3
(SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM PPM
100 5 (PEL) 10 (TWA)
Polyolefin / Hydrocarbon; CAS proprietary
This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments
and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts.
SECTION 3 - HEALTH HAZARD DATA
ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES
EYES: Particulates may scratch eye surfaces causing Flush eyes with clear running water for a minimum of 15
mechanical irritation. minutes while holding eyelids open; if irritation persists, seek
medical attention.
SKIN: Frequent or prolonged contact may cause irritation to Flush with clear running water for a minimum of 15 minutes;
the skin. if irritation persists, seek medical attention.
INGESTION: This product is generally considered to have a NOT ordinarily required.
low order of acute oral toxicity.
INHALATION: Product is not expected to cause irritation to NOT ordinarily required.
the nose, throat or respiratory tract.
HEALTH HAZARDS (ACUTE AND CHRONIC): This product is not considered a health hazard.
NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No
CARCINOGENICITY
No additional information
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Preexisting eye, skin, or breathing disorders may
become aggravated through exposure.
Form Revised 06/01/2001
MATERIAL SAFETY DATA SHEET
IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2
Date: September 1, 2004
Petro Lock II鈩?
SECTION 4 - FIRE FIGHTING MEASURES
FLASH POINT (METHOD USED) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component)
>266潞F (Pen-Martin) LEL: Not Applicable UEL: Not Applicable
EXTINGUISHING MEDIA
Water fog, Dry chemicals, Foam, CO2
SPECIAL FIRE FIGHTING PROCEDURES
DO NOT enter confine fire space without full bunker gear (Helmet with face shield, bunker coats, gloves and rubber boots. Wear
NIOSH/MSHA approved self contained breathing apparatus. Cool fire exposed containers with water.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS
Material may burn at or above flashpoint, and airborne dust may explode if ignited. Product can accumulate static charges when
handled. Thermal decomposition may emit toxic and irritating substances.
SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES
STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED
In case of accidental spills, provide adequate ventilation; avoid generating dust. Sweep up material or vacuum (using HEPA filter equipped
system) if possible to avoid generating airborne dust. Place spilled material into a clean, dry container for disposal.
WASTE DISPOSAL METHODS
Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous waste
upon contact with other products. Refer to "40 CFR Protection of Environment Parts 260-299" for complete waste disposal regulations.
Consult your Local, State, or Federal Environmental Protection Agency before disposing of any chemicals.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE
Keep container(s) tightly closed when not in use. Store in cool, dry area. Keep this and other chemicals out of reach of children.
SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION
RESPIRATORY PROTECTION VENTILATION LOCAL EXHAUST: Recommended
MECHANICAL (GENERAL): Not Required
Ordinarily, none required
PROTECTIVE GLOVES EYE PROTECTION
Impervious rubber Safety goggles
OTHER PROTECTIVE CLOTHING OR EQUIPMENT WORK / HYGIENIC PRACTICES
Ordinarily, none required Practice safe work habits. Use according to label instructions.
SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES
BOILING POINT BULK DENSITY
Not applicable 30 鈥? 35 lb./cu. ft.
VAPOR PRESSURE (mm Hg) MELTING POINT
Not applicable Not applicable
VAPOR DENSITY (AIR=1) pH
Not applicable Not applicable
SOLUBILITY IN WATER EVAPORATION RATE (n-BUTYL ACETATE=1)
Negligible Not applicable
APPEARANCE AND ODOR % VOLATILES (BY WEIGHT)
Not applicable
White, fluffed particulate; essentially odorless
SECTION 8 - STABILITY AND REACTIVITY
STABILITY CONDITIONS TO AVOID
UNSTABLE:
STABLE: XXX Extreme temperatures
INCOMPATIBILITIES (MATERIALS TO AVOID)
Extended storage periods (>30 days) at temperatures above 150潞F may cause changes in resin properties.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
Decomposition will not occur if handled / stored properly. Thermal decomposition may emit irritating and toxic gases (carbon monoxide and
dioxide, methane, acetones, and other ketones).
HAZARDOUS POLYMERIZATION CONDITIONS TO AVOID
MAY OCCUR:
WILL NOT OCCUR: XXX None known
The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information
is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by
the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury
caused by abnormal use of this material even if reasonable safety procedures are followed.
MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ Willaim L. Gaiter Pkwy., Buffalo, NY 14215 (716) 895-1822
Form Revised 06/01/2001
|