S a f e c o a t?br>
DynoFlex
Natural Tan
DESCRIPTION: Safecoat DynoFlex is a unique, water COVERAGE: 100 square feet per gallon at 15 mils
based, low odor elastomeric sealer that comes in a paste- thickness.
like compound for sealing seams, joints and cracks in new
and old heating and air conditioning ducts, and for repairing CLEAN-UP: Clean tools and equipment while they are still
metal roofs and asphalt shingles. Also comes in a wet with a solution of SafeChoice Super Clean and warm
sprayable form that can be used over Safecoat DynoSeal water.
as a topcoat for roofs and decks.
DRYING/CURING TIME: To touch within 2 hours. Cures
Safecoat DynoFlex is highly resistant to harsh weather and hard in 24 hours.
temperature changes. It remains flexible and prevents
leaks even after exposure to the elements or contraction LIMITATIONS: Do not apply when ambient or surface
due to weather It is resistant to gasoline, oil, grease, fungi, temperature is below 55 degrees F. Avoid application in
acids, alkalines and flame spread. Safecoat DynoFlex is direct hot sun, which may cause premature dryout. If
also a superb sound deadener. product has thickened in container add a small amount of
water and stir to return product to original paste
PRODUCT NUMBER AND CONTAINER SIZE: 51173 consistency. Safecoat DynoFlex does not contain
(quart) and 51373 (five gallon). formaldehyde preservatives. Do not contaminate. When
not in use keep container closed.
USE ON: Safecoat DynoFlex is recommended for new and
old heating and air conditioning ducts, metal roof cracks, HEALTH PRECAUTIONS: As with all coatings and stains,
damaged asphalt shingles, mobile home roofs and similar keep container tightly closed and out of the reach of
areas. In the sprayable form, it is recommended as a children. Do not take internally. Keep from freezing. Always
topcoat for Safecoat DynoSeal. use adequate ventilation. If you are chemically sensitive,
always test for personal tolerance.
ADVANTAGES / SIGNIFICANT BENEFITS:
Effective, easy to use. LIMITED LIABILITY: The great variation between
Non-offensive to installer and occupant. environmental factors, possible surfaces and application
techniques, and the lack of control we have over such
When used in conjunction with SafeChoice Super
matters, must affect our policies. Safecoat products are
Clean and SafeChoice X-158, DynoFlex is a full
guaranteed not to be defective when applied and used in
system for sealing, cleaning and maintaining all
accordance with instructions. However, liability, whether
heating and air conditioning ducts.
express or implied, is limited solely to replacement of
Safely used by and for the chemically sensitive.
product or refund of purchase price and shall under no
Very low VOC content, meets or exceeds all federal
circumstances include liability for labor costs or
and state air quality regulations, including California.
consequential damages. Because of the variety of
circumstances affecting each job, it is the user's
APPLICATION: Always have adequate ventilation. All
responsibility to determine the suitability and safety of the
areas to be coated should be clean and dry. Remove all
product for any particular application. This limited warranty
oil, dirt, dust, rust and loose residue. When possible clean
may not be modified or extended by manufacturer's
with a not toxic, biodegradable and odorless cleaner like
representatives, distributors, or dealers of AFM products.
SafeChoice Super Clean. Old asphalt shingles should be
We particularly recommend that users always test in
power washed prior to treatment. Allow all surfaces to dry
small inconspicuous areas before application to the
completely before applying DynoFlex. Apply DynoFlex at
entire surface.
15 mils wet directly from the container without dilution. Use
a brush, squeegee-type applicator or trowel and smooth
evenly to produce a uniform and seamless coat. Two coats
provides additional protection.
AMERICAN FORMULATING AND MANUFACTURING
3251 Third Avenue, San Diego, CA 92103 ?Tel: 619-239-0321 Fax: 619-239-0565
MATERIAL SAFETY DATA SHEET
Prepared according to 29 CFR 1910.1200
N/A = Not applicable Revised 1/15/03
SECTION 1 - PRODUCT IDENTIFICATION Splash (eyes): Flush immediately with large amounts of water for at least 15
minutes, lifting upper and lower eyelids occasionally. Take to a physician for
medical treatment.
Trade Name: Safecoat DynoFlex Textured Natural
Splash (skin): Remove with soap and water. Remove contaminated clothing.
Product I.D.# & Color: 5173 Tan
Supply copious amounts of fresh water to the skin areas to rinse material away.
Product Class: Waterborne Polymer Emulsion
Ingestion (Swallowing): Consult with physician, hospital emergency room, or
Supplier's Name: American Formulating & Manufacturing
poison control center immediately. Only if conscious, give 2 glasses of water to
Telephone #: (619) 239-0321 Fax # 619-239-0565
drink.
Address: 3251 Third Avenue, San Diego, CA 92103
Notes to Physician: Any treatment that might be required for overexposure
Emergency Phone (MSDS Information): (619) 239-0321 or (562) 693-0872
should be directed at the control of symptoms and the clinical conditions.
D.O.T. Emergency Phone Number: (562) 693-0872
US DOT Hazard Shipping Class: Not regulated - aqueous SECTION 6 - REACTIVITY DATA
D.O.T. Labels/Placards Required: No
OSHA Class: 29CFR 1910.1200 Non-hazardous Stability: Stable, however avoid temperatures above 177癈/350癋, the onset of
SARA TITLE III Emergency & Community Right to Know: polymer decomposition.
Section 311/312 Categorizations (40 CFR 370): Not a hazardous chemical Incompatibility (materials to avoid): Avoid materials that are water reactive,
Section 313 Information (40 CFR 372): See Section 2 highly alkaline or highly acidic.
Hazardous Decomposition by-products: CO, CO2 on combustion
SECTION 2 ?INGREDIENTS Hazardous Polymerization: Will not occur.
Conditions to Avoid: Excess heat may cause containers to rupture. Avoid
Modified Acrylic Copolymer CAS #: Mixture Weight Percent: temperatures below 45癋 or freezing conditions.
45 ?50 Water CAS # 7732-18-5 Weight SECTION 7 - SPILL, DISPOSAL PROCEDURES; ENVIRONMENTAL DATA
Percent: 35 ?40
Propylene Glycol CAS #: 57-55-6 Weight Percent: < 3 Steps to be taken in case material is released or spilled: Confine in small
Vapor Pressure 0.22 mm Hg @ 77 F area; contain and remove with inert absorbent (sand, earth, etc.). Place in proper
Magnesium Aluminum Silicate CAS #: 12174-11-7 Weight Percent: 1.61 container for proper disposal. CAUTION - Keep out of waterways, drains, sewers
PEL-OSHA 15mg/M3 (Total Dust) 5mg/M3(Respirable Dust) by diking. Keep spectators away. Floor may be slippery. Use care to avoid
TLV-ACGIH 10 mg/M3 (Inhalable particulate) 3mg/M3 (Respirable Particulate) falling.
Waste Disposal Method: Place contaminated material in suitable sealed metal
Suspected Cancer Agents: OSHA: No NTP: NO IARC: No None known. containers for disposal. Do not incinerate closed containers. Use non leaking
HMIS Codes: H-1 F-0 R-0 P-B containers, seal tightly and label properly. Do not pour contaminated paint back
into unused paint. Do not throw liquid paint into the trash. Where allowed by
SECTION 3 - PHYSICAL DATA local laws (check with local regulatory agencies) allow liquid waste materials to
dry out before disposing into trash containers. Take all liquid unused paint that
Boiling Point: (Water) 212F cannot be used to approved recycling centers, paint roundups, or county facilities
Melting Point: ....................................................N/A that are approved to take unused paint at collection sites. Contact state, county,
Vapor Density:...................................................Heavier than air city health services or fire departments to find nearest collection centers. Do not
% Volatile by Volume: .......................................44.73 dispose of waste into water streams or storm water sewers. Do not mix with
LBS/GAL Theoretical: .......................................9.65 +or- .15 other kinds of waste. Dispose all waste in accordance with local, state and
Solubility in Water: ............................................Dilutable federal regulations.
Vapor Pressure, mmHg @ 20degC: .................N/A RCRA Classification: As produced, this product is not a waste. If discarded as
Evaporation Rate:..............................................Slower than ether is, it is not classified a "Hazardous" waste under RCRA. This product is not
% Volatile by Weight.........................................42.17 ignitable, corrosive, reactive, or toxic; therefore is not defined as hazardous by the
Specific Gravity (Water=1):...............................1.16 EPA.
VOC Material:....................................................29 grams/liter, 0.24 lb/gal Environmental Hazards: None known.
VOC Material less H20: ...................................50 grams/liter, 0.42 lb/gal SECTION 8 - SPECIAL PROTECTION INFORMATION
SECTION 4 - FIRE & EXPLOSION HAZARD DATA Respiratory Protection: If applied by spraying, use an appropriate, properly
fitted NIOSH/MSHA approved respirator to remove spray mist. Good room
Flash Point: N/A non-combustible (mechanical) ventilation should be sufficient protection against vapors from
Flammable limits in air, volume % - lower LEL: 2.6 Upper UEL: 12.5 product. If further protection is desired or if persons are sensitive to vapors, use
Fire Extinguishing Media: Water, carbon dioxide, dry chemical a respirator with a NIOSH/MSHA approval number TC-23C-860 or TC-23C-87 or
Personal Protective Equipment: Self-contained breathing apparatus (pressure- an equivalent. Refer to OSHA 29 CFR 1910.134, "Respiratory Protection".
demand MSHA/NIOSH approved or equivalent) and full protective gear may be Ventilation: General (mechanical) room ventilation is expected to be
worn if desired, but not necessary for normal use. satisfactory.
Autoignition Temp.: N/A Protective Gloves: None required under most conditions. If protection is
Special Fire Fighting Procedures: Use water (fog) to cool closed containers. desired, plastic, nitrile or latex rubber will provide adequate protection.
Wear self contained breathing apparatus. Eye Protection: Safety glasses or goggles with side shields if splashing may
Unusual Fire & Explosion Hazards: Closed containers may explode due to the occur. Use goggles when spraying, ANSI Z87.1 or approved equivalent.
build up of steam pressure when exposed to extreme heat. Material can splatter Other Protection: Eye wash or copious amounts of water as a precautionary
above 100癈/212癋. Polymer film can burn. measure is suggested. Other equipment not likely to be needed.
SECTION 9 - STORAGE & SPECIAL HANDLING
SECTION 5 - HEALTH HAZARD INFORMATION & FIRST AID
Storage Temperature: Min. 45degF - Max. 120degF/Indoor and outdoor = OK
Threshold Limit Value: See Section 2. This product should be stored at room temperature to prolong shelf life. Keep
Symptoms of Overexposure containers in a cool, dry place. Avoid subjecting this product to extreme
Symptoms and Effects of Short Term Exposure: Acute. Primary route of temperature variations and freezing. Adverse conditions can cause emulsion
coagulation.
entry:
KEEP CONTAINER CLOSED. KEEP OUT OF REACH OF CHILDREN. DO
Swallowing: May cause gastrointestinal irritation, nausea, vomiting and
diarrhea. NOT TAKE INTERNALLY. DO NOT GET IN EYES. IF PRODUCT IS
Inhalation: Inhalation-spray mists may cause mild respiratory irritation. If SPRAYED, PREVENT PROLONGED OR REPEATED BREATHING OF SPRAY
material enters lungs during swallowing or vomiting, can cause lung inflammation MIST. USE ADEQUATE VENTILATION WHEN USING THIS PRODUCT. USE
and damage. GOOD HYGIENE PRACTICES AND WASH AFTER USING PRODUCT.
Eye Contact: Liquid splashed into the eye may cause transient eye
irritation. NOTICE: The data and recommendations presented herein are based upon our
Skin Absorption: None known. research and the research of others, and are believed to be accurate. No
Symptoms and Effects of Repeated Overexposure: Chronic - None known. guarantee of their accuracy is made, however, and the product discussed is
Medical Conditions Generally Aggravated by Exposure: None known. distributed without warranty, expressed or implied, and the person receiving such
Emergency & First Aid Procedures: product shall make his own determination of the suitability thereof for his
Inhalation: Remove from exposure. Provide plenty of fresh air. particular purpose. The use of this information and the conditions and use of this
product are controlled by the user, and it is the responsibility and obligation of the
user to determine the conditions of safe use of this product. If persons using this
product are chemically sensitive, a test for personal tolerance is recommended.
|