AMBIENT METALLIC
MATERIAL SAFETY DATA SHEET
INCLUDES
Ambient Metallic consists of Armor-Coat 1200MTM and Master-Coat 100TM. Below are the MSDS sheets for both.
ARMOR COAT 1200M
MATERIAL SAFETY DATA SHEET
PRODUCT IDENTIFICATION
Master Coating Technologies Medical & Transport Emergency Contact:
2740 31st Avenue South INFOTRAC: 1.800.535.5053
Minneapolis, MN 55406 MSDS Date: 07.02.2004
612.722.8808 DOT Classification: Not Regulated
Supersedes: All Previous CAS Number: Mixture
Trade Name: Scuffmaster Armor-Coat 1200M
Synonyms: AC1200M, 7241, 7242, 72043, 7244, 7245
Chemical Family: Urethane/Pigment Dispersion
PHYSICAL DATA
Boiling Range (F): 212?(water) Solubility in Water: Dilutable
Freezing Point (F): 32?(water) Specific Gravity: 1.1 - 1.3
Vapor Density (Air=1): < 1 % Volatile by Weight: 33.5
Vapor Pressure (mmHg @ 68?F): 17 pH Information: 9.0 - 10.0
VOC: 142 g/L
Evaporation Rate (Butyl Acetate = 1): 1 (water) Appearance & Odor: Liquid, metallic color
HAZARDOUS INGREDIENTS
Ingredient Percent PPM MG/M3 CAS Number
Esther Alcohol 1-2 None Established N/A 25265-77-4
Aluminum Flake 5 - 15 N/A 15-OSHA PEL & 10-ACGIH TLV 7429-90-5
Stoddard Solvent 1-2 N/A 525-OSHA PEL & 525-ACGIH TLV 8052-41-3
Aromatic Solvent 1-2 N/A 245 - Supplier Recommendation 64742-95-6
This paint mixture contains titanium dioxide and/or other pigments SECTION 313 SUPPLIER NOTIFICATION: This product contains the
classified by ACGIH as "nuisance dusts." Exposures to spray mist or following toxic chemicals subject to the reporting requirements of section
sanding dust should be controlled to below 10mg/m3 through usage 313 of the Emergency Planning and Community Right-To-Know Act of
of NIOSH/MSHA TC23C or equivalent approved dust filter respirators. 1986 and of 40 CRF 372.
Follow respirator manufacturer's directions for use. NONE above the minimum concentrations.
HMIS Rating: Health = 1 Flammability = 1 Reactivity = 0 Personal Protection = B*
*User should determine appropriate personal protective equipment based on use conditions.
HEALTH HAZARD DATA
TOXICITY DATA: SOLVENTS: Oral LD50 rat > 5000 mg/kg ( essentially nontoxic ) ?dermalLD50 rabbit > 3160 mg/kg ( slight toxic )
ALUMINUM: None. No toxic effects are known.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE AND ROUTES OF ENTRY. Entry Routes: Inhalation, Ingestion, Skin Contact, Eye Contact
Effects of Overexposure: N/A Effects of Inhalation: Trace component, residual monomer, and other organics may be irritating to the eyes,
skin, mucous membranes, respiratory tract and may produce symptoms of headache and nausea in poorly ventilated areas. Effects of Ingestion:
DO NOT INGEST. While aluminum content is non-toxic and the solvents are only slightly toxic by oral ingestion, minute amounts of certain portions
of the solvents, if aspirated into the lungs during ingestion, may cause severe pulmonary injury or death. Effects of Skin Contact: Prolonged
contact can cause transient reddening of the skin. Effect of Eye Contact: Direct contact may be irritating to eyes. Effects of Repeated
Overexposure: This paint mixture as provided shows no evidence of chronic effects from available information.
Page 1 of 2
AC1200M ?MATERIAL SAFETY DATA SHEET ( continued )
EMERGENCY FIRST AID PROCEDURES
Eye Contact: Immediately flush eyes for 15 minutes occasionally lifting eyelids. If victim wears contact lenses, remove lenses and continue
rinsing. Clean lenses before reusing. If irritation continued, consult a physician. Skin Contact: Wash effected area thoroughly with mild
soap and water. If irritation develops and persists, consult a physician. Inhalation: Move to fresh air if necessary. If irritation persists,
consult a physician. If victim is not breathing, artificial respiration should be administered by qualified personnel. Seek immediate medical
attention. Ingestion: If swallowed, give lots of water, and induce vomiting. If necessary consult a physician.
FIRE & EXPLOSION HAZARD DATA
Flash Point: 104?F ( 40癈) Minimum (Method - Setaflash) Fire Extinguishing Media:
LEL: Not determined (aqueous system) Use Class B and Class D extinguishers
UEL: Not determined (aqueous system) Special Fire Fighting Procedures:
Use breathing apparatus when fighting enclosed fires.
Unusual Fire and Explosion Hazard:
Dried solids can burn, giving of carbon dioxide, carbon monoxide, aluminum oxide, nitrogen oxide, ammonia and phosphorous oxide.
Aluminum flake can react with some acid and caustic solutions to form gas and heat.
REACTIVITY DATA
This product is stable under normal (ambient) conditions and hazardous polymerization will not occur. Hazardous Decomposition Products:
Combustion of dried film may produce carbon dioxide and carbon monoxide. Conditions or Materials to Avoid: None.
SPILL OR LEAK PROCEDURES
Spill: Major spills should be collected for disposal. Minor spills may be flushed to sewer if permitted by local, state, and federal regulations.
Waste Disposal: Incinerate or bury in suitable landfills where permitted by appropriate government regulations.
SPECIAL PROTECTION INFORMATION
Respiratory Protection: Use appropriate MAHA/NIOSH approved respirator in areas with poor ventilation and when exposed to spray mists
or sanding dusts. Ventilation: General room ventilation is expected to be satisfactory. Use local exhaust if needed for mist or vapor.
Protective Gloves: Wear gloves impervious to water and soap. Eye Protection: Wear goggles if spraying and available eye bath.
Disclaimer: The information in this MSDS was obtained from sources we believe are reliable. However, the information is provided without any representation or warranty,
expressed or implied, regarding its accuracy or completeness. The conditions or handling, storage, use and disposal of the product are beyond our control and may be beyond
our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected
with the handling, storage, use or disposal of this product. Disposal of containers should be in accordance with applicable federal, state and local laws and regulations.
Thank you for selection Scuffmaster.
technical support: 1.800.898.0219 documents: www.scuffmaster.com
Page 2 of 2
MA STER COAT 100
MATERIAL SAFETY DATA SHEET
PRODUCT IDENTIFICATION
Master Coating Technologies Medical & Transport Emergency Contact:
2740 31st Avenue South INFOTRAC: 1.800.535.5053
Minneapolis, MN 55406 MSDS Date: 07.02.2004
612.722.8808 DOT Classification: Not Regulated
Supersedes: All Previous CAS Number: Mixture
Trade Name: Scuffmaster Master-Coat 100
Synonyms: MC100, 7221, 7222, 7223, 7224, 7225
Chemical Family: Acrylic/Urethane Dispersion
PHYSICAL DATA
Boiling Range (F): 212?(water) Solubility in Water: Dilutable
Freezing Point (F): 32?(water) Specific Gravity: 1.2 - 1.3
Vapor Density (Air=1): <1 % Volatile by Weight: 50.9
Vapor Pressure (mmHg @ 68?F): 17 pH Information: 9.0 - 10.0
VOC: 112 g/L
Evaporation Rate (Butyl Acetate = 1): 1 (water) Appearance & Odor: Liquid, colors, latex odor
HAZARDOUS INGREDIENTS
Ingredient Percent PPM MG/M3 CAS Number
Propylene Glycol 1-2 400 N/A 57-55-6
Esther Alcohol 3 None Established N/A 25265-77-4
This paint mixture contains titanium dioxide and/or other pigments classified by ACGIH as
"nuisance dusts." Exposures to spray mist or sanding dust should be controlled to below
10mg/m3 through usage of NIOSH/MSHA TC23C or equivalent approved dust filter respirators.
Follow respirator manufacturer's directions for use.
SECTION 313 SUPPLIER NOTIFICATION: This product contains the following toxic chemicals
subject to the reporting requirements of section 313 of the Emergency Planning and Community
Right-To-Know Act of 1986 and of 40 CRF 372. NONE above the minimum concentrations.
HMIS Rating: Health = 1 Flammability = 0 Reactivity = 0 Personal Protection = B*
*User should determine appropriate personal protective equipment based on use conditions.
HEALTH HAZARD DATA
Entry Routes: Inhalation, Ingestion, Skin Contact, Eye Contact Effects of Overexposure: N/A Effects of Inhalation: Trace component,
residual monomer, and other organics may be irritating to the eyes, skin, mucous membranes, respiratory tract and may produce symptoms
of headache and nausea in poorly ventilated areas. Effects of Ingestion: Irritating to gastrointestinal tract, abdominal pain, and diarrhea.
Effects of Skin Contact: Prolonged contact can cause transient reddening of the skin. Effect of Eye Contact: Direct contact may be
irritating to eyes. Effects of Repeated Overexposure: This paint mixture as provided shows no evidence of chronic effects from
available information
Page 1 of 2
MC100 ?MATERIAL SAFETY DATA SHEET ( continued )
EMERGENCY FIRST AID PROCEDURES
Eye Contact: Immediately flush eyes for 15 minutes occasionally lifting eyelids. If victim wears contact lenses, remove lenses and continue
rinsing. Clean lenses before reusing. If irritation continued, consult a physician. Skin Contact: Wash effected area thoroughly with mild
soap and water. If irritation develops and persists, consult a physician. Inhalation: Move to fresh air if necessary. If irritation persists,
consult a physician. If victim is not breathing, artificial respiration should be administered by qualified personnel. Seek immediate medical
attention. Ingestion: Give lots of water to dilute, and induce vomiting. If necessary consult a physician.
FIRE & EXPLOSION HAZARD DATA
Flash Point: Not determined (aqueous system) Fire Extinguishing Media
LEL: Not determined (aqueous system) Non-Flammable (aqueous emulsion)
UEL: Not determined (aqueous system) If water evaporates, remaining material can burn.
Special Fire Fighting Procedures Use breathing Use all-purpose foam for large fires, and CO2 or
apparatus when fighting enclosed fires dry chemical media for small fires
Unusual Fire and Explosion Hazard:
Products will not burn but may spatter if temperature exceeds boiling point of water. Dried solids can burn, giving of oxides and carbon.
REACTIVITY DATA
This product is stable under normal (ambient) conditions and hazardous polymerization will not occur. Hazardous Decomposition Products:
Combustion of dried film may produce carbon dioxide and carbon monoxide. Conditions or Materials to Avoid: None.
SPILL OR LEAK PROCEDURES
Spill: Major spills should be collected for disposal. Minor spills may be flushed to sewer if permitted by local, state, and federal regulations.
Waste Disposal: Incinerate or bury in suitable landfills where permitted by appropriate government regulations.
SPECIAL PROTECTION INFORMATION
Respiratory Protection: Use appropriate MAHA/NIOSH approved respirator in areas with poor ventilation and when exposed to spray
mists or sanding dusts. Ventilation: General room ventilation is expected to be satisfactory. Use local exhaust if needed for mist or
vapor. Protective Gloves: Wear gloves impervious to water and soap. Eye Protection: Wear goggles if spraying and available eye bath.
Disclaimer: The information in this MSDS was obtained from sources we believe are reliable. However, the information is provided without any representation or warranty,
expressed or implied, regarding its accuracy or completeness. The conditions or handling, storage, use and disposal of the product are beyond our control and may be beyond
our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected
with the handling, storage, use or disposal of this product. Disposal of containers should be in accordance with applicable federal, state and local laws and regulations.
Thank you for selection Scuffmaster.
technical support: 1.800.898.0219 documents: www.scuffmaster.com
Page 2 of 2
|