ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 1 of 12
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
ASA EXELFLEX TRADE
SYNONYMS
"wall / floor adhesive"
PRODUCT USE
Adhesive for wall and floor applications. Suitable over concrete, cement render,
screeds, fibrous cement sheeting and waterproof approved
SUPPLIER
Company: Architectural & Structural Adhesives Company: Architectural & Structural Adhesives
Address: Address:
PO Box 6722 106-108 Redfern St
Wetherill Park Wetherill Park
NSW, 2164 NSW, 2164
AUS AUS
Fax: +61 2 9725 4427 Telephone: +61 2 9725 4666
Telephone: 1800 813 890
Fax: +61 2 9725 4427
Section 2 - HAZARDS IDENTIFICATION
STATEMENT OF HAZARDOUS NATURE
HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the
Criteria of NOHSC, and the ADG Code.
POISONS SCHEDULE
None
RISK
Causes burns.
Risk of serious damage to eyes.
Inhalation may produce health damage*.
Cumulative effects may result following exposure*.
Limited evidence of a carcinogenic effect*.
Possible respiratory and skin sensitiser*.
* (limited evidence).
SAFETY
Keep locked up.
Do not breathe dust.
Avoid contact with eyes.
Wear suitable protective clothing.
Use only in well ventilated areas.
Keep container in a well ventilated place.
To clean the floor and all objects contaminated by this material, use water and
detergent.
Take off immediately all contaminated clothing.
In case of accident or if you feel unwell IMMEDIATELY contact Doctor or Poisons
Information Centre (show label if possible).
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 2 of 12
Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME CAS RN %
portland cement 65997-15-1 11-60
styrene/ butadiene rubber 61789-96-6 11-60
silica amorphous 7631-86-9 11-60
styrene/ acrylic acid/ butyl acrylate copolymer 25586-20-3 11-60
Section 4 - FIRST AID MEASURES
SWALLOWED
- For advice, contact a Poisons Information Centre or a doctor at once.
- Urgent hospital treatment is likely to be needed.
- If swallowed do NOT induce vomiting.
- If vomiting occurs, lean patient forward or place on left side (head-down
position, if possible) to maintain open airway and prevent aspiration.
- Observe the patient carefully.
- Never give liquid to a person showing signs of being sleepy or with reduced
awareness; i.e. becoming unconscious.
- Give water to rinse out mouth, then provide liquid slowly and as much as
casualty can comfortably drink.
- Transport to hospital or doctor without delay.
EYE
If this product comes in contact with the eyes:
- Immediately hold eyelids apart and flush the eye continuously with running
water.
- Ensure complete irrigation of the eye by keeping eyelids apart and away from
eye and moving the eyelids by occasionally lifting the upper and lower lids.
- Continue flushing until advised to stop by the Poisons Information Centre or a
doctor, or for at least 15 minutes.
- Transport to hospital or doctor without delay.
- Removal of contact lenses after an eye injury should only be undertaken by
skilled personnel.
SKIN
If skin or hair contact occurs:
- Immediately flush body and clothes with large amounts of water, using safety
shower if available.
- Quickly remove all contaminated clothing, including footwear.
- Wash skin and hair with running water. Continue flushing with water until
advised to stop by the Poisons Information Centre.
- Transport to hospital, or doctor.
INHALED
- If fumes or combustion products are inhaled remove from contaminated area.
- Lay patient down. Keep warm and rested.
- Prostheses such as false teeth, which may block airway, should be removed,
where possible, prior to initiating first aid procedures.
- Apply artificial respiration if not breathing, preferably with a demand valve
resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if
necessary.
- Transport to hospital, or doctor, without delay.
NOTES TO PHYSICIAN
Treat symptomatically.
For acute or short-term repeated exposures to highly alkaline materials:
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 3 of 12
Section 4 - FIRST AID MEASURES
- Respiratory stress is uncommon but present occasionally because of soft tissue
edema.
- Unless endotracheal intubation can be accomplished under direct vision,
cricothyroidotomy or tracheotomy may be necessary.
- Oxygen is given as indicated.
- The presence of shock suggests perforation and mandates an intravenous line
and fluid administration.
- Damage due to alkaline corrosives occurs by liquefaction necrosis whereby the
saponification of fats and solubilisation of proteins allow deep penetration
into the tissue.
Alkalis continue to cause damage after exposure.
INGESTION:
- Milk and water are the preferred diluents
No more than 2 glasses of water should be given to an adult.
- Neutralising agents should never be given since exothermic heat reaction may
compound injury.
* Catharsis and emesis are absolutely contra-indicated.
* Activated charcoal does not absorb alkali.
* Gastric lavage should not be used.
Supportive care involves the following:
- Withhold oral feedings initially.
- If endoscopy confirms transmucosal injury start steroids only within the first
48 hours.
- Carefully evaluate the amount of tissue necrosis before assessing the need for
surgical intervention.
- Patients should be instructed to seek medical attention whenever they develop
difficulty in swallowing (dysphagia).
SKIN AND EYE:
- Injury should be irrigated for 20-30 minutes.
Eye injuries require saline. [Ellenhorn & Barceloux: Medical Toxicology].
Section 5 - FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
- There is no restriction on the type of extinguisher which may be used.
Use extinguishing media suitable for surrounding area.
FIRE FIGHTING
- Alert Fire Brigade and tell them location and nature of hazard.
- Wear breathing apparatus plus protective gloves for fire only.
- Prevent, by any means available, spillage from entering drains or water
courses.
- Use fire fighting procedures suitable for surrounding area.
- DO NOT approach containers suspected to be hot.
- Cool fire exposed containers with water spray from a protected location.
- If safe to do so, remove containers from path of fire.
- Equipment should be thoroughly decontaminated after use.
FIRE/EXPLOSION HAZARD
- Solid which exhibits difficult combustion or is difficult to ignite.
- Avoid generating dust, particularly clouds of dust in a confined or
unventilated space as dusts may form an explosive mixture with air, and any
source of ignition, i.e. flame or spark, will cause fire or explosion. Dust
clouds generated by the fine grinding of the solid are a particular hazard;
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 4 of 12
Section 5 - FIRE FIGHTING MEASURES
accumulations of fine dust may burn rapidly and fiercely if ignited
- Dry dust can also be charged electrostatically by turbulence, pneumatic
transport, pouring, in exhaust ducts and during transport.
- Build-up of electrostatic charge may be prevented by bonding and grounding.
- Powder handling equipment such as dust collectors, dryers and mills may
require additional protection measures such as explosion venting.
- All movable parts coming in contact with this material should have a speed of
less than 1-meter/sec.
Decomposition may produce toxic fumes of, carbon dioxide (CO2), metal oxides,
other pyrolysis products typical of burning organic material.
NOTE: Burns with intense heat. Produces melting, flowing, burning liquid and
dense acrid black smoke.
May emit poisonous fumes.
May emit corrosive fumes.
FIRE INCOMPATIBILITY
Avoid contamination with oxidising agents i.e. nitrates, oxidising acids,
chlorine bleaches, pool chlorine etc. as ignition may result.
HAZCHEM
None
Personal Protective Equipment
Breathing apparatus.
Gas tight chemical resistant suit.
Limit exposure duration to 1 BA set30 mins.
Section 6 - ACCIDENTAL RELEASE MEASURES
EMERGENCY PROCEDURES
MINOR SPILLS
- Remove all ignition sources.
- Clean up all spills immediately.
- Avoid contact with skin and eyes.
- Control personal contact by using protective equipment.
- Use dry clean up procedures and avoid generating dust.
- Place in a suitable labelled container for waste disposal.
MAJOR SPILLS
Moderate hazard.
- CAUTION: Advise personnel in area.
- Alert Emergency Services and tell them location and nature of hazard.
- Control personal contact by wearing protective clothing.
- Prevent, by any means available, spillage from entering drains or water
courses.
- Recover product wherever possible.
- IF DRY: Use dry clean up procedures and avoid generating dust. Collect
residues and place in sealed plastic bags or other containers for disposal. IF
WET: Vacuum/shovel up and place in labelled containers for disposal.
- ALWAYS: Wash area down with large amounts of water and prevent runoff into
drains.
- If contamination of drains or waterways occurs, advise Emergency Services.
EMERGENCY RESPONSE PLANNING GUIDELINES (ERPG)
The maximum airborne concentration below which it is believed that nearly all
individuals could be exposed for up to one hour WITHOUT experiencing or developing
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 5 of 12
Section 6 - ACCIDENTAL RELEASE MEASURES
life-threatening health effects is:
silica amorphous 500 mg/m鲁
irreversible or other serious effects or symptoms which could
impair an individual's ability to take protective action is:
silica amorphous 50 mg/m鲁
other than mild, transient adverse effects
without perceiving a clearly defined odour is:
silica amorphous 30 mg/m鲁
The threshold concentration below which most people.
will experience no appreciable risk of health effects:
silica amorphous 6 mg/m鲁
American Industrial Hygiene Association (AIHA)
Ingredients considered according to the following cutoffs
Very Toxic (T+) >= 0.1% Toxic (T) >= 3.0%
R50 >= 0.25% Corrosive (C) >= 5.0%
R51 >= 2.5%
else >= 10%
where percentage is percentage of ingredient found in the mixture
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
- Avoid all personal contact, including inhalation.
- Wear protective clothing when risk of exposure occurs.
- Use in a well-ventilated area.
- Prevent concentration in hollows and sumps.
- DO NOT enter confined spaces until atmosphere has been checked.
- DO NOT allow material to contact humans, exposed food or food utensils.
- Avoid contact with incompatible materials.
- When handling, DO NOT eat, drink or smoke.
- Keep containers securely sealed when not in use.
- Avoid physical damage to containers.
- Always wash hands with soap and water after handling.
- Work clothes should be laundered separately. Launder contaminated clothing
before re-use.
- Use good occupational work practice.
- Observe manufacturer's storing and handling recommendations.
- Atmosphere should be regularly checked against established exposure standards
to ensure safe working conditions are maintained.
SUITABLE CONTAINER
- Polyethylene or polypropylene container.
- Check all containers are clearly labelled and free from leaks.
STORAGE INCOMPATIBILITY
Avoid reaction with oxidising agents.
STORAGE REQUIREMENTS
Observe manufacturer's storing and handling recommendations.
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 6 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
Source Material TWA TWA STEL STEL Peak Peak
ppm mg/m鲁 ppm mg/m鲁 ppm mg/m鲁
_________________________ ________________ _____ _____ _____ _____ _____ _____
Australia Exposure Portland cement 10
Standards (a)
Australia Exposure Fumed silica 2
Standards (respirable
dust)
Australia Exposure Inspirable dust 10
Standards (Not specified)
No data available: styrene/ butadiene rubber as (CAS: 61789-96-6) / (CAS: 9003-55-8)
No data available: silica amorphous as (CAS: 112945-52-5)
No data available: styrene/ acrylic acid/ butyl acrylate copolymer as (CAS: 25586-20-3)
EMERGENCY EXPOSURE LIMITS
Material Revised IDLH Revised IDLH
Value (ppm) Value (mg/m3)
Portland cement 5,000
Silica, amorphous 3,000
No data for ASA Exelflex Trade.
INGREDIENT DATA
PORTLAND CEMENT:
Portland cement is considered to be a nuisance dust that does not cause
fibrosis and has little potential to induce adverse effects on the lung.
STYRENE/ BUTADIENE RUBBER:
TLV TWA: 0.001 mg/m鲁 (as total proteins) Inhalable fraction skin sensitiser
as rubber processing fume:
MEL-TWA: 0.6 mg/m鲁 as cyclohexane solubles [HSE, UK]
BRMA-TWA: 0.25 mg/m鲁 as cyclohexane solubles [BRMA Code of Practice]
Rubber fume is a complex and indeterminate mixture of substances and is defined
as "fume evolved in the mixing, milling and blending of natural rubber and
synthetic polymers combined with chemicals, and in the processes which convert
the resultant blend into finished products or parts thereof, and including any
inspection procedures where fume continues to be evolved".
"Fume" generally describes solid particles generated by chemical reactions, or
by condensation from the gaseous state, usually after volatilisation from melted
substances, and often accompanied by a chemical reaction such as oxidation or
thermal breakdown.
Several chemical agents may occur in rubber fume which are experimental or
animal carcinogens, however, given the number of chemicals used or formed during
rubber making, difficulties arise in attributing a particular effect to a given
exposure.
Stomach cancer has been associated with work in jobs early in the production
line; lung and lower oesophagus cancer with all work processes; and lymphomas
with jobs where co-exposure to solvents occurs. Other cancers have also been
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 7 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
reported with liver tumours appearing as a secondary phenomenon. No no-effect
levels have been determined.
Two studies showed no excess of bladder cancer in workers entering the industry
after 1950: the excess risk before that date is thought to result from exposure
to residual beta-naphthylamines previously used as anti-oxidants.
as rubber process dust:
MEL-TWA: 6 mg/m鲁 [HSE, UK]
Rubber process dust is a complex, variable mixture of particulates defined as
"dust arising in the stages of rubber manufacture where ingredients are handled,
weighed, added to or mixed with natural or synthetic elastomers. It does not
include dusts arising from the abrasion of cured rubber but occurs during the
preparation of compounds of either synthetic or natural rubber.
There is some evidence that occupational exposure to rubber dusts produces an
excess incidence of stomach cancer. HSE data concluded that there was a small
but significant excess of stomach cancer associated with the initial processes
in rubber manufacture. Stomach cancer shows a marked social class gradient,
which may lead to an over-estimation of the risk.
One report from the USA stated that exposure in rubber processing areas produces
pulmonary disease but this has not been supported by UK epidemiology nor reports
from the industry.
No no-effect level has been determined. The MEL was considered appropriate
because it was felt reasonably practical for industry to comply with this value.
SILICA AMORPHOUS:
IDLH Level: 3000 mg/m鲁
STYRENE/ ACRYLIC ACID/ BUTYL ACRYLATE COPOLYMER:
These "dusts" have little adverse effect on the lungs and do not produce toxic
effects or organic disease. Although there is no dust which does not evoke some
cellular response at sufficiently high concentrations, the cellular response
caused by P.N.O.C.s has the following characteristics:
- the architecture of the air spaces remain intact,
- scar tissue (collagen) is not synthesised to any degree,
- tissue reaction is potentially reversible.
Extensive concentrations of P.N.O.C.s may:
- seriously reduce visibility,
- cause unpleasant deposits in the eyes, ears and nasal passages,
- contribute to skin or mucous membrane injury by chemical or mechanical action,
per se, or by the rigorous skin cleansing procedures necessary for their
removal. [ACGIH]
This limit does not apply:
- to brief exposures to higher concentrations
- nor does it apply to those substances that may cause physiological impairment
at lower concentrations but for which a TLV has as yet to be determined.
This exposure standard applies to particles which
- are insoluble or poorly soluble* in water or, preferably, in aqueous lung
fluid (if data is available) and
- have a low toxicity (i.e.. are not cytotoxic, genotoxic, or otherwise
chemically reactive with lung tissue, and do not emit ionizing radiation, cause
immune sensitization, or cause toxic effects other than by inflammation or by a
mechanism of lung overload).
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 8 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
PERSONAL PROTECTION
EYE
- Chemical goggles.
- Full face shield may be required for supplementary but never for primary
protection of eyes
- Contact lenses may pose a special hazard; soft contact lenses may absorb and
concentrate irritants. A written policy document, describing the wearing of lens
or restrictions on use, should be created for each workplace or task. This
should include a review of lens absorption and adsorption for the class of
chemicals in use and an account of injury experience. Medical and first-aid
personnel should be trained in their removal and suitable equipment should be
readily available. In the event of chemical exposure, begin eye irrigation
immediately and remove contact lens as soon as practicable. Lens should be
removed at the first signs of eye redness or irritation - lens should be removed
in a clean environment only after workers have washed hands thoroughly. [CDC
NIOSH Current Intelligence Bulletin 59].
HANDS/FEET
Wear chemical protective gloves, eg. PVC.
Wear safety footwear or safety gumboots, eg. Rubber.
NOTE: The material may produce skin sensitisation in predisposed individuals.
Care must be taken, when removing gloves and other protective equipment, to
avoid all possible skin contact.
OTHER
- Overalls.
- P.V.C. apron.
- Barrier cream.
- Skin cleansing cream.
- Eye wash unit.
ENGINEERING CONTROLS
Local exhaust ventilation usually required. If risk of overexposure exists, wear
approved respirator. Correct fit is essential to obtain adequate protection.
Supplied-air type respirator may be required in special circumstances. Correct
fit is essential to ensure adequate protection.
An approved self contained breathing apparatus (SCBA) may be required in some
situations.
Provide adequate ventilation in warehouse or closed storage area.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE
Light grey powder; insoluble in water.
PHYSICAL PROPERTIES
Does not mix with water.
Sinks in water.
Alkaline.
Molecular Weight: Not Applicable Boiling Range (C): Not Applicable
Melting Range (C): Not Applicable Specific Gravity (water=1): 1.35
Solubility in water (g/L): Immiscible pH (as supplied): Not Applicable
pH (1% solution): Not Applicable Vapour Pressure (kPa): Not Applicable
Volatile Component (%vol): Not Applicable Evaporation Rate: Not Applicable
Relative Vapour Density (air=1): Not Applicable Flash Point (C): Not Applicable
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 9 of 12
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
Lower Explosive Limit (%): Not Applicable Upper Explosive Limit (%): Not Applicable
Autoignition Temp (C): Not Available Decomposition Temp (掳C): Not Available
State: Divided Solid Viscosity: Not Applicable
Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION
CONDITIONS CONTRIBUTING TO INSTABILITY
- Presence of incompatible materials.
- Product is considered stable.
- Hazardous polymerisation will not occur.
Section 11 - TOXICOLOGICAL INFORMATION
POTENTIAL HEALTH EFFECTS
ACUTE HEALTH EFFECTS
SWALLOWED
The material can produce chemical burns within the oral cavity and
gastrointestinal tract following ingestion.
EYE
The material can produce chemical burns to the eye following direct contact.
Vapours or mists may be extremely irritating.
SKIN
The material can produce chemical burns following direct contact
with the skin.
Entry into the blood-stream, through, for example, cuts, abrasions or lesions,
may produce systemic injury with harmful effects. Examine the skin prior to the
use of the material and ensure that any external damage is suitably protected.
The material may cause skin irritation after prolonged or repeated exposure and
may produce on contact skin redness, swelling, the production of vesicles,
scaling and thickening of the skin.
INHALED
Inhalation of dusts, generated by the material during the course of normal
handling, may be damaging to the health of the individual.
The material can cause respiratory irritation in some persons. The body's
response to such irritation can cause further lung damage.
Effects on lungs are significantly enhanced in the presence of respirable
particles.
CHRONIC HEALTH EFFECTS
Repeated exposures, in an occupational setting, to high levels of fine- divided
dusts may produce a condition known as pneumoconiosis which is the lodgement of
any inhaled dusts in the lung irrespective of the effect. This is particularly
true when a significant number of particles less than 0.5 microns (1/50,000
inch), are present. Lung shadows are seen in the X-ray. Symptoms of
pneumoconiosis may include a progressive dry cough, shortness of breath on
exertion, increased chest expansion, weakness and weight loss. As the disease
progresses the cough produces a stringy mucous, vital capacity decreases further
and shortness of breath becomes more severe. Pneumoconiosis is the accumulation
of dusts in the lungs and the tissue reaction in its presence. It is further
classified as being of noncollagenous or collagenous types. Noncollagenous
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 10 of 12
Section 11 - TOXICOLOGICAL INFORMATION
pneumoconiosis, the benign form, is identified by minimal stromal reaction,
consists mainly of reticulin fibres, an intact alveolar architecture and is
potentially reversible. Asthma-like symptoms may continue for months or even
years after exposure to the material ceases. This may be due to a non-allergenic
condition known as reactive airways dysfunction syndrome (RADS) which can occur
following exposure to high levels of highly irritating compound. Key criteria
for the diagnosis of RADS include the absence of preceding respiratory disease,
in a non-atopic individual, with abrupt onset of persistent asthma-like symptoms
within minutes to hours of a documented exposure to the irritant. A reversible
airflow pattern, on spirometry, with the presence of moderate to severe
bronchial hyperreactivity on methacholine challenge testing and the lack of
minimal lymphocytic inflammation, without eosinophilia, have also been included
in the criteria for diagnosis of RADS. RADS (or asthma) following an irritating
inhalation is an infrequent disorder with rates related to the concentration of
and duration of exposure to the irritating substance. Industrial bronchitis, on
the other hand, is a disorder that occurs as result of exposure due to high
concentrations of irritating substance (often particulate in nature) and is
completely reversible after exposure ceases. The disorder is characterised by
dyspnea, cough and mucous production. There has been some concern that this
material can cause cancer or mutations but there is not enough data to make an
assessment. There is some evidence that inhaling this product is more likely to
cause a sensitisation reaction in some persons compared to the general
population. There is limited evidence that, skin contact with this product is
more likely to cause a sensitisation reaction in some persons compared to the
general population. Respiratory sensitisation may result in allergic/asthma like
responses; from coughing and minor breathing difficulties to bronchitis with
wheezing, gasping.
Section 12 - ECOLOGICAL INFORMATION
DO NOT discharge into sewer or waterways.
Refer to data for ingredients, which follows:
SILICA AMORPHOUS:
Aquatic toxicity (Daphnia magna) 24h EC50: >1000 mg/l
Fish toxicity (Brachydanio rerio) 96h LC50: >10,000 mg/l [Grace]
Section 13 - DISPOSAL CONSIDERATIONS
If container can not be cleaned sufficiently well to ensure none of the original
product remains or if the container cannot be used to store the same product,
then puncture containers, to prevent re-use, and bury at an authorised landfill.
- Recycle wherever possible.
- Consult manufacturer for recycling options or consult local or regional waste
management authority for disposal if no suitable treatment or disposal facility
can be identified.
- Dispose of by: Burial in a licenced land-fill or Incineration in a licenced
apparatus (after admixture with suitable combustible material)
- Decontaminate empty containers. Observe all label safeguards until containers
are cleaned and destroyed.
Section 14 - TRANSPORTATION INFORMATION
HAZCHEM
None
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 11 of 12
Section 14 - TRANSPORTATION INFORMATION
NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS:UN,IATA,IMDG
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE
None
REGULATIONS
portland cement (CAS: 65997-15-1) is found on the following regulatory lists;
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
OECD Representative List of High Production Volume (HPV) Chemicals
styrene/ butadiene rubber (CAS: 61789-96-6) is found on the following regulatory
lists;
Australia Inventory of Chemical Substances (AICS)
styrene/ butadiene rubber (CAS: 9003-55-8) is found on the following regulatory
lists;
Australia Inventory of Chemical Substances (AICS)
International Agency for Research on Cancer (IARC) Carcinogens
silica amorphous (CAS: 7631-86-9) is found on the following regulatory lists;
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
International Agency for Research on Cancer (IARC) Carcinogens
International Council of Chemical Associations (ICCA) - High Production Volume
List
OECD Representative List of High Production Volume (HPV) Chemicals
silica amorphous (CAS: 112945-52-5) is found on the following regulatory lists;
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
OECD Representative List of High Production Volume (HPV) Chemicals
styrene/ acrylic acid/ butyl acrylate copolymer (CAS: 25586-20-3) is found on
the following regulatory lists;
Australia Inventory of Chemical Substances (AICS)
Section 16 - OTHER INFORMATION
Ingredients with multiple CAS Nos
Ingredient Name Cas Nos
styrene/ butadiene 61789-96-6, 9003-55-8
rubber
silica amorphous 7631-86-9, 112945-52-5
This document is copyright. Apart from any fair dealing for the purposes of
private study, research, review or criticism, as permitted under the Copyright
Act, no part may be reproduced by any process without written permission from
CHEMWATCH. TEL (+61 3) 9572 4700.
continued...
ASA EXELFLEX TRADE
Chemwatch Material Safety Data Sheet
Issue Date: 17-Jun-2004 CHEMWATCH 4990-24
C317SC CD 2006/1 Page 12 of 12
Section 16 - OTHER INFORMATION
Issue Date: 17-Jun-2004
Print Date: 9-Mar-2006
|