232376 E. Pacifica Place Rancho Dominguez, CA 90220 (800) 675-1118 www.alliedhightech.com
MATERIAL/CHEMICAL SAFETY DATA SHEET
SECTION 3: HAZARDS IDENTIFICATION
SECTION 1: CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Warning: Flammable liquid and vapor. Causes eye, skin and
Product Details respiratory tract irritation.
Silicone Cold Mold Release
Product Name:
Routes of Entry: Skin, inhalation, eyes.
- Spray
200-10010
Allied Item No.:
Chemical Name: Silicon Solution
SECTION 4: FIRST AID MEASURES
Company Identification Potential First Aid/
Health Effects Medical Info.
Allied High Tech Products, Inc.
Eye Contact: Moderate eye irritation. Flush with water for 15
2376 East Pacifica Place
minutes, seek medical
Rancho Dominguez, CA 90220 attention.
(310) 635-2466
Contact Point
Transportation for United States
Skin Contact: Prolonged or repeated Wash with soap and
Chemtrec (800) 424-9300 * (202) 483-7616
contact may cause water. Remove contami-
irritation. nated clothing. If irritation
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENT persists, seek medical
Exposure Limits in Air Carcin. attention.
Chemical Name CAS No. ACGIH TLV or TWA OSHA PEL Y/N
Remove to fresh air. If
Inhalation: Vapors and mists will
Hydrotreated Heavy 64742-48-9 NA NA N
discomfort persists, seek
irritate nose, throat and
Naphtha 60-100%
medical attention.
possibly the eyes.
Dibutyl Ether 10-30% 142-96-1 NA NA N
Octane 1-5% 111-65-9 NA N
2350 mg/m3/
500 ppm Ingestion: May be harmful if Keep individual calm. Do
swallowed. NOT induce vomiting:
contains petroleum
distillates and/or aromatic
solvents. Seek medical
attention immediately.
Note: Existing Conditions Aggravated by Exposure: Skin disorders.
SECTION 5: FIRE FIGHTING MEASURES
Extinguishing Media: Alcohol foam, carbon dioxide or dry chemical.
Fire Fighting Instruction: Wear full protective clothing and OSHA/NIOSH self-
contained breathing apparatus with full facepiece.
Special Hazards: Containers exposed to fire should be cooled with water to prevent
vapor pressure buildup which could result in container rupture. If a leak or spill has
not ignited use water spray to disperse vapors. The liquid is volatile and gives off
invisible vapors.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Remove all sources of ignition. Prevent material from contaminating
ground water system. Contain with absorbent material such as clay,
soil or any commercially available absorbent. Transfer contaminated
HMIS Ratings
Ingredients are listed on the TSCA Inventory of absorbent, soil and other materials into recovery or salvage drums for
1
Health:
Chemical Substances. disposal.
Flammability: 3
Those not identified are non-hazardous.
Reactivity: 0
Page 1 of 2:
2376 E. Pacifica Place ?Rancho Dominguez, CA 90220 ?(800) 675-1118 ?www.alliedhightech.com
SECTION 7: HANDLING & STORAGE SECTION 12: ECOLOGICAL INFORMATION
Handling: Keep away from heat, spark and flame. Keep No specific studies have been conducted on the ecotoxicity or environmental
container closed. Avoid contact with eyes, skin and clothing. Do fate of this material; however, commonly available data on the material
indicate that uncontrolled releases to soil, groundwater or surface waters
not wear contact lenses. Observe good house keeping practices.
could entail acute and/or chronic ecological effects depending on the quantity
and concentration of such releases. Releases of volatile components to the
Storage: Store away from heat, sparks, flames or other sources
atmosphere are not believed to entail significant ecological consequences
of ignition. Keep container closed. Store at or below 120 癋
provided such releases are within the exposure levels set forth in this
(48.8 癈). document. Accordingly, all appropriate measure should be taken to avoid
uncontrolled releases to the environment and any spills or other uncontrolled
releases which may occur should be contained and cleaned up immediately
in accordance with Section 6.
SECTION 8: EXPOSURE CONTROL & PERSONAL PROTECTION SECTION 13: DISPOSAL INFORMATION
Engineering Measures: Local exhaust system designed for flammable gas
Incinerate of waste material according to Federal,
atmospheres to remove vapors.
State and Local regulations. Dispose of contami-
Respiratory Protection: Use OSHA/NIOSH approved respiratory protection if level nated packaging as residue.
of air contaminants is excessive.
Protective Gloves: Use impervious gloves, apron and boots.
Eye Protection: Safety glasses or chemical splash goggles.
Other: Eyewash, safety shower and impervious clothing are recommended.
SECTION 9: PHYSICAL & CHEMICAL PROPERTIES SECTION 14: TRANSPORT INFORMATION
DOT Shipping Name: Resin solution.
Appearance: Colorless liquid
Odor: Mild, solvent DOT Hazard Class: 3, III
Solubility: Slight DOT Id Number: UN1866
Boiling Point: >235 癋 (112 癈)
IATA & IMO/IMDG Shipping Name/Class: Resin solution.
Melting Point: NA
Flash Point: 87 癋 (31 癈) IATA & IMO/IMDG Class: 3, PGII
Vapor Pressure: NA IATA & IMO/IMDG UN or Id Number: UN1866
Vapor Density: Heavier than air
Evaporation Rate: Slower than ether
SECTION 15: REGULATORY INFORMATION
Specific Gravity: .754
Flammable Limits LEL: NA CA Proposition 65: This product contains chemicals known to the state of
California to cause cancer, birth defects or other reproductive harm.
Flammable Limits UEL: NA
Toxic Substance Control Act TSCA: All ingredients are TSCA listed.
SECTION 10: STABILITY & REACTIVITY CERCLA: This product is not classified as hazardous.
Stability: Stable
Canada CEPA DSL/NDSL Status: One or more components are not listed on and
are not exempt from listing on either the DSL or the NDSL.
Conditions to Avoid/Incompatibles: Keep away from heat, sparks and
flame. Oxidizing agents. Canada WHMIS Hazard Class: B.2, D.2.A, D.2.B
Decomposition Products: None under normal use.
SECTION 16: OTHER INFORMATION
Hazardous Polymerization: Will not occur.
Legend
SECTION 11: TOXICOLOGICAL INFORMATION NAIF: No Applicable Information Found
NA: Not Available/Applicable
This material is not listed as a carcinogen by IARC, NTP or
NE: None Established
OSHA.
DISCLAIMER: The above information and recommendations are
believed accurate and reliable. Because it is not possible to anticipate
all conditions of use, additional safety precautions may be required.
ALLIED HIGH TECH PRODUCTS, INC. makes no warranty, either
express or implied, as to its accuracy or completeness and none is
made as to the fitness of this material for any purpose. The
manufacturer/distributor shall not be liable for damages to person or
property resulting from its use. Nothing herein shall be construed as a
recommendation for use in violation of any patent.
Page 2 of 2: Form Prepared By: Allied High Tech Products, Inc. January 2010
|