3M MATERIAL SAFETY DATA SHEET COMPUBLEND(tm) II BASE U 10/23/2002
Material Safety Data Sheet
Copyright, 2002, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: COMPUBLEND(tm) II BASE U
MANUFACTURER: 3M
DIVISION: Commercial Care Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 10/23/2002
Supercedes Date: 10/16/2002
Document Group: 11-3758-7
Product Use:
Specific Use: CLEANING CHEMICAL
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
WATER 7732-18-5 30 - 60
ACRYLIC ACID, POLYMERS 9003-01-4 10 - 30
EDTA TETRASODIUM SALT 64-02-8 10 - 30
SODIUM HYDROXIDE 1310-73-2 5 - 10
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Clear golden yellow color, mild odor
General Physical Form: Liquid
Immediate health, physical, and environmental hazards:
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Single exposure, above recommended guidelines, may cause:
Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness,
Page 1 of 5
3M MATERIAL SAFETY DATA SHEET COMPUBLEND(tm) II BASE U 10/23/2002
and nose and throat pain.
Prolonged or repeated exposure, above recommended guidelines, may cause:
Lung Effects: Signs/symptoms may include difficulty breathing, cough, wheezing, weakness, increased heart rate, bluish
colored skin (cyanosis), sputum production and changes in lung function tests.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, nausea, diarrhea and vomiting.
Chemical (Aspiration) Pneumonitis: Signs/symptoms may include coughing, gasping, choking, burning of the mouth, difficulty
breathing, bluish colored skin (cyanosis), and may be fatal.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get medical attention.
Skin Contact: Immediately flush skin with large amounts of water. If signs/symptoms develop, get medical attention.
Inhalation: If signs/symptoms develop, remove person to fresh air. If signs/symptoms persist, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give
anything by mouth to an unconscious person. Get immediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Not Applicable
Autoignition temperature
Not Applicable
Flash Point
Not Applicable
Flammable Limits - LEL
Not Applicable
Flammable Limits - UEL
Not Applicable
OSHA Flammability Classification:
5.2 EXTINGUISHING MEDIA
Material will not burn.
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Nonflammable.
Unusual Fire and Explosion Hazards: Not applicable.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more
information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be
cleaned up by qualified personnel. Ventilate the area with fresh air. Contain spill. Working from around the edges of the spill
inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it
appears dry. Collect as much of the spilled material as possible. Clean up residue with water. Place in a closed container approved
for transportation by appropriate authorities. Dispose of collected material as soon as possible.
Page 2 of 5
3M MATERIAL SAFETY DATA SHEET COMPUBLEND(tm) II BASE U 10/23/2002
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid eye contact with vapors, mists, or spray. Avoid skin contact. Do not eat, drink or smoke when using this product. Wash
exposed areas thoroughly with soap and water. Keep out of the reach of children.
7.2 STORAGE
Store under normal warehouse conditions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use in a well-ventilated area.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray. The following eye protection(s) are recommended: Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure
assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber, Neoprene, Nitrile Rubber.
8.2.3 Respiratory Protection
Use in a well-ventilated area.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
SODIUM HYDROXIDE ACGIH CEIL 2 mg/m3
SODIUM HYDROXIDE CMRG TWA 2 mg/m3
SODIUM HYDROXIDE OSHA CEIL 2 mg/m3 Table Z-1A
SODIUM HYDROXIDE OSHA TWA 2 mg/m3 Table Z-1
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Clear golden yellow color, mild odor
Odor, Color, Grade:
Liquid
General Physical Form:
Not Applicable
Autoignition temperature
Not Applicable
Flash Point
Not Applicable
Flammable Limits - LEL
Not Applicable
Flammable Limits - UEL
Page 3 of 5
3M MATERIAL SAFETY DATA SHEET COMPUBLEND(tm) II BASE U 10/23/2002
212 篎
Boiling point
No Data Available
Density
No Data Available
Vapor Density
No Data Available
Vapor Pressure
Approximately 1.3 [Ref Std: WATER=1]
Specific Gravity
9.5 - 10.5
pH
Not Applicable
Melting point
Complete
Solubility in Water
Approximately 1 [Ref Std: WATER=1]
Evaporation rate
Not Applicable
Volatile Organic Compounds
40 - 70 %
Percent volatile
Not Applicable
VOC Less H2O & Exempt Solvents
<=100 centipoise
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
CHEMICAL FATE INFORMATION
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility in the presence of a combustible material. As a disposal
alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number UPC ID Number UPC
61-5000-6959-8 00-48011-14708-6
Page 4 of 5
3M MATERIAL SAFETY DATA SHEET COMPUBLEND(tm) II BASE U 10/23/2002
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
CHEMICAL INVENTORIES
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
The components of this product are in compliance with the chemical notification requirements of TSCA.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 0 Reactivity: 0 Special Hazards: None
Acid/Base: Alkaline
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 2 Flammability: 0 Reactivity: 0 Protection: X - See PPE section.
Hazardous Material Identification System (HMIS(r)) hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS(r) ratings are to be used with a fully implemented HMIS(r) program. HMIS(r) is a registered mark of the National Paint and
Coatings Association (NPCA).
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
Page 5 of 5
|