--------------------------------------------------------------------------
603183-00 MOBIL ALMO 525
MATERIAL SAFETY DATA BULLETIN
--------------------------------------------------------------------------
--------------------------------------------------------------------------
1. PRODUCT AND COMPANY IDENTIFICATION
--------------------------------------------------------------------------
PRODUCT NAME: MOBIL ALMO 525
SUPPLIER: EXXONMOBIL OIL CORPORATION
3225 GALLOWS RD.
FAIRFAX, VA 22037
24 - Hour Health and Safety Emergency (call collect): 609-737-4411
24 - Hour Transportation Emergency:
CHEMTREC: 800-424-9300 202-483-7616
LUBES AND FUELS: 281-834-3296
Product and Technical Information:
Lubricants and Specialties: 800-662-4525 800-443-9966
Fuels Products: 800-947-9147
MSDS Fax on Demand: 713-613-3661
MSDS Internet Website: http://www.exxon.com, http://www.mobil.com
--------------------------------------------------------------------------
2. COMPOSITION/INFORMATION ON INGREDIENTS
--------------------------------------------------------------------------
CHEMICAL NAMES AND SYNONYMS: PET. HYDROCARBONS AND ADDITIVES
GLOBALLY REPORTABLE MSDS INGREDIENTS:
None.
See Section 8 for exposure limits (if applicable).
--------------------------------------------------------------------------
3. HAZARDS IDENTIFICATION
--------------------------------------------------------------------------
This product may be considered hazardous according to regulatory
guidelines (See Section 15).
EMERGENCY OVERVIEW: Amber Liquid. DOT ERG No. : NA
POTENTIAL HEALTH EFFECTS: This product may be used in certain
applications where misting can occur. Exposure to oil mist may
result in eye and skin irritation. Excessive exposure to mists
may cause respiratory irritation or damage.
For further health effects/toxicological data, see Section 11.
--------------------------------------------------------------------------
4. FIRST AID MEASURES
--------------------------------------------------------------------------
EYE CONTACT: Flush thoroughly with water. If irritation occurs, call
a physician.
SKIN CONTACT: Wash contact areas with soap and water. Remove and
clean oil soaked clothing daily and wash affected area. (See
Section 16 - Injection Injury)
INHALATION: If respiratory irritation, dizziness, nausea, or
unconsciousness occurs due to excessive vapor or mist exposure,
seek immediate medical assistance. If breathing has stopped,
assist ventilation with a mechanical device or mouth-to-mouth
resuscitation.
INGESTION: Not expected to be a problem. Seek medical attention if
discomfort occurs. Do not induce vomiting.
NOTE TO PHYSICIANS: Pre-existing conditions which may be aggravated by
exposure include emphysema and asthma.
--------------------------------------------------------------------------
5. FIRE-FIGHTING MEASURES
--------------------------------------------------------------------------
EXTINGUISHING MEDIA: Carbon dioxide, foam, dry chemical and water fog.
SPECIAL FIRE FIGHTING PROCEDURES: Water or foam may cause frothing.
Use water to keep fire exposed containers cool. Water spray may
be used to flush spills away from exposure. Prevent runoff from
fire control or dilution from entering streams, sewers, or
drinking water supply.
SPECIAL PROTECTIVE EQUIPMENT: For fires in enclosed areas, fire
fighters must use self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: None.
COMBUSTION PRODUCTS: Fumes, smoke, carbon monoxide, sulfur oxides,
metal oxides, aldehydes and other decomposition products, in the
case of incomplete combustion.
Flash Point C(F): > 121(250) (ASTM D-93).
Flammable Limits (approx.% vol.in air) - LEL: 0.9%, UEL: 7.0%
NFPA HAZARD ID: Health: 0, Flammability: 1, Reactivity: 0
--------------------------------------------------------------------------
6. ACCIDENTAL RELEASE MEASURES
--------------------------------------------------------------------------
NOTIFICATION PROCEDURES: Report spills/releases as required to
appropriate authorities. U.S. Coast Guard and EPA regulations
require immediate reporting of spills/releases that could reach
any waterway including intermittent dry creeks. Report
spill/release to Coast Guard National Response Center toll free
number (800)424-8802. In case of accident or road spill notify
CHEMTREC (800) 424-9300.
PROCEDURES IF MATERIAL IS RELEASED OR SPILLED:
LAND SPILL: Shut off source taking normal safety precautions. Take
measures to minimize the effects on ground water. Recover by
pumping or contain spilled material with sand or other suitable
absorbent and remove mechanically into containers. If necessary,
dispose of adsorbed residues as directed in Section 13.
WATER SPILL: Confine the spill immediately with booms. Warn other
ships in the vicinity. Notify port and other relevant authorities.
Remove from the surface by skimming or with suitable absorbents. If
permitted by regulatory authorities the use of suitable dispersants
should be considered where recommended in local oil spill
procedures.
ENVIRONMENTAL PRECAUTIONS: Prevent material from entering sewers,
water sources or low lying areas; advise the relevant authorities
if it has, or if it contaminates soil/vegetation.
PERSONAL PRECAUTIONS: See Section 8
--------------------------------------------------------------------------
7. HANDLING AND STORAGE
--------------------------------------------------------------------------
HANDLING: Avoid inhalation of vapors or mists. See Section 8 for
additional personal protection advice when handling this product.
STORAGE: Keep containers closed when not in use. Do not store in open
or unlabelled containers. Store away from strong oxidizing
agents and combustible materials. Do not store near heat,
sparks, flame or strong oxidants.
SPECIAL PRECAUTIONS: Prevent small spills and leakages to avoid slip
hazard.
EMPTY CONTAINER WARNING: Empty containers retain residue (liquid
and/or vapor) and can be dangerous. DO NOT PRESSURIZE, CUT, WELD,
BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT,
FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION;
THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to
refill or clean container since residue is difficult to remove.
Empty drums should be completely drained, properly bunged and
promptly returned to a drum reconditioner. All containers should
be disposed of in an environmentally safe manner and in
accordance with governmental regulations.
--------------------------------------------------------------------------
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
--------------------------------------------------------------------------
OCCUPATIONAL EXPOSURE LIMITS:
When mists/aerosols can occur, the following are recommended: 5 mg/m3
(as oil mist)- ACGIH Threshold Limit Value (TLV), 10 mg/m3 (as oil mist)
- ACGIH Short Term Exposure Limit (STEL), 5 mg/m3 (as oil mist) - OSHA
Permissible Exposure Limit (PEL)
VENTILATION: Use adequate ventilation, local exhaust, or enclosures to
control below exposure limits.
RESPIRATORY PROTECTION: When ventilation is not adequate, wear
approved respirator.
EYE PROTECTION: Chemical type goggles should be worn during misting
operations. Normal industrial eye protection practices should be
employed for other use conditions.
SKIN PROTECTION: Not normally required. When splashing or liquid
contact can occur frequently, wear oil resistant gloves and/or
other protective clothing. Good personal hygiene practices
should always be followed.
--------------------------------------------------------------------------
9. PHYSICAL AND CHEMICAL PROPERTIES
--------------------------------------------------------------------------
Typical physical properties are given below. Consult Product Data Sheet
for specific details.
APPEARANCE: Liquid
COLOR: Amber
ODOR: Mild
ODOR THRESHOLD-ppm: NE
pH: NA
BOILING POINT C(F): > 316(600)
MELTING POINT C(F): NA
FLASH POINT C(F): > 121(250) (ASTM D-93)
FLAMMABILITY (solids): NE
AUTO FLAMMABILITY C(F): NA
EXPLOSIVE PROPERTIES: NA
OXIDIZING PROPERTIES: NA
VAPOR PRESSURE-mmHg 20 C: < 0.1
VAPOR DENSITY: > 2.0
EVAPORATION RATE: NE
RELATIVE DENSITY, 15/4 C: 0.883
SOLUBILITY IN WATER: Negligible
PARTITION COEFFICIENT: NE
VISCOSITY AT 40 C, cSt: 38.5
VISCOSITY AT 100 C, cSt: 6.6
POUR POINT C(F): < -24(-11)
FREEZING POINT C(F): NE
VOLATILE ORGANIC COMPOUND: NE
DMSO EXTRACT, IP-346 (WT.%): <3, for mineral oil only
NA=NOT APPLICABLE NE=NOT ESTABLISHED D=DECOMPOSES
FOR FURTHER TECHNICAL INFORMATION, CONTACT YOUR MARKETING REPRESENTATIVE
--------------------------------------------------------------------------
10. STABILITY AND REACTIVITY
--------------------------------------------------------------------------
STABILITY (THERMAL, LIGHT, ETC.): Stable.
CONDITIONS TO AVOID: Extreme heat and high energy sources of ignition.
INCOMPATIBILITY (MATERIALS TO AVOID): Strong oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Product does not decompose at
ambient temperatures.
HAZARDOUS POLYMERIZATION: Will not occur.
--------------------------------------------------------------------------
11. TOXICOLOGICAL DATA
--------------------------------------------------------------------------
---ACUTE TOXICOLOGY---
ORAL TOXICITY (RATS): Practically non-toxic (LD50: greater than 2000
mg/kg). ---Based on testing of similar products and/or the
components.
DERMAL TOXICITY (RABBITS): Practically non-toxic (LD50: greater than
2000 mg/kg). ---Based on testing of similar products and/or the
components.
INHALATION TOXICITY (RATS): Practically non-toxic (LC50: greater
than 5 mg/l). ---Based on testing of similar products and/or the
components.
EYE IRRITATION (RABBITS): Practically non-irritating. (Draize score:
greater than 6 but 15 or less). ---Based on testing of similar
products and/or the components.
SKIN IRRITATION (RABBITS): Practically non-irritating. (Primary
Irritation Index: greater than 0.5 but less than 3). ---Based
on testing of similar products and/or the components.
OTHER ACUTE TOXICITY DATA: Although an acute inhalation study was not
performed with this product, a variety of mineral oils, such as
those in this product, have been tested. These samples had
virtually no effect other than a nonspecific inflammatory
response in the lung to the aerosolized mineral oil. The
presence of additives in other tested formulations (in
approximately the same amounts as in the present formulation) did
not alter the observed effects.
---SUBCHRONIC TOXICOLOGY (SUMMARY)---
Severely solvent refined and severely hydrotreated mineral base oils
have been tested at ExxonMobil by dermal application to rats
5/days/week for 90 days at doses significantly higher than those
expected during normal industrial exposure. Extensive
evaluations including microscopic examination of internal organs
and clinical chemistry of body fluids, showed no adverse effects.
---CHRONIC TOXICOLOGY (SUMMARY)---
Repeated and/or prolonged exposure may cause irritation to the skin,
eyes or respiratory tract. Overexposure to oil mist may result
in oil droplet deposition and/or granuloma formation. The base
oils in this product are severely solvent refined and/or severely
hydrotreated. Chronic mouse skin painting studies of severely
treated oils showed no evidence of carcinogenic effects. These
results are confirmed on a continuing basis using various
screening methods such as the Modified Ames Test, IP-346, and/or
other analytical methods.
---SENSITIZATION (SUMMARY)---
Not expected to be sensitizing based on tests of this product,
components, or similar products.
---OTHER TOXICOLOGY DATA---
Small metal particles from machining may cause abrasion of the skin
and may predispose to dermatitis.
--------------------------------------------------------------------------
12. ECOLOGICAL INFORMATION
--------------------------------------------------------------------------
ENVIRONMENTAL FATE AND EFFECTS:
ECOTOXICITY: Not established.
MOBILITY: Not established.
PERSISTENCE AND DEGRADABILITY: Not established.
BIOACCUMULATIVE POTENTIAL: Not established.
--------------------------------------------------------------------------
13. DISPOSAL CONSIDERATIONS
--------------------------------------------------------------------------
WASTE DISPOSAL: Product is suitable for burning in an enclosed,
controlled burner for fuel value. Such burning may be limited
pursuant to the Resource Conservation and Recovery Act. In
addition, the product is suitable for processing by an approved
recycling facility or can be disposed of at an appropriate
government waste disposal facility. Use of these methods is
subject to user compliance with applicable laws and regulations
and consideration of product characteristics at time of disposal.
RCRA INFORMATION: The unused product, in our opinion, is not
specifically listed by the EPA as a hazardous waste (40 CFR,
Part 261D), nor is it formulated to contain materials which
are listed hazardous wastes. It does not exhibit the hazardous
characteristics of ignitability, corrosivity, or reactivity. The
unused product is not formulated with substances covered by the
Toxicity Characteristic Leaching Procedure (TCLP). However, used
product may be regulated.
--------------------------------------------------------------------------
14. TRANSPORT INFORMATION
--------------------------------------------------------------------------
USA DOT: NOT REGULATED BY USA DOT.
RID/ADR: NOT REGULATED BY RID/ADR.
IMO: NOT REGULATED BY IMO.
IATA: NOT REGULATED BY IATA.
STATIC ACCUMULATOR (50 picosiemens or less): YES
--------------------------------------------------------------------------
15. REGULATORY INFORMATION
--------------------------------------------------------------------------
US OSHA HAZARD COMMUNICATION STANDARD: This product may be used in
certain applications where misting can occur. According to OSHA
29 CFR 1910.1200, certain mineral oil mists may be considered
hazardous if the workplace airborne concentration exceeds 5 mg/m3
(ACGIH TLV).
EU Labeling: Product is not dangerous as defined by the European Union
Dangerous Substances/Preparations Directives. EU labeling not
required.
Governmental Inventory Status: All components comply with TSCA,
EINECS/ELINCS, AICS, METI, and DSL.
U.S. Superfund Amendments and Reauthorization Act (SARA) Title III:
This product contains no "EXTREMELY HAZARDOUS SUBSTANCES".
SARA (311/312) REPORTABLE HAZARD CATEGORIES: None.
This product contains no chemicals subject to the supplier notification
requirements of SARA (313) toxic release program.
The following product ingredients are cited on the lists below:
CHEMICAL NAME CAS NUMBER LIST CITATIONS *
------------- ---------- --------------
ZINC (ELEMENTAL ANALYSIS) (<0.10%) 7440-66-6 22
CHLORINE (ELEMENTAL ANALYSIS) 7782-50-5 22
(<0.90%)
CHLORO ALKANES (1.93%) 61788-76-9 21, 22
PHOSPHORODITHOIC ACID, O,O-DI 68649-42-3 22
C1-14-ALKYL ESTERS, ZINC SALTS (2:
1) (ZDDP) (0.73%)
--- REGULATORY LISTS SEARCHED ---
1=ACGIH ALL 6=IARC 1 11=TSCA 4 16=CA P65 CARC 21=LA RTK
2=ACGIH A1 7=IARC 2A 12=TSCA 5a2 17=CA P65 REPRO 22=MI 293
3=ACGIH A2 8=IARC 2B 13=TSCA 5e 18=CA RTK 23=MN RTK
4=NTP CARC 9=OSHA CARC 14=TSCA 6 19=FL RTK 24=NJ RTK
5=NTP SUS 10=OSHA Z 15=TSCA 12b 20=IL RTK 25=PA RTK
26=RI RTK
* EPA recently added new chemical substances to its TSCA Section 4 test rules.
Please contact the supplier to confirm whether the ingredients in this product
currently appear on a TSCA 4 or TSCA 12b list.
Code key:CARC=Carcinogen; SUS=Suspected Carcinogen; REPRO=Reproductive
--------------------------------------------------------------------------
16. OTHER INFORMATION
--------------------------------------------------------------------------
USE: AIR TOOL LUBRICANT
NOTE: PRODUCTS OF EXXON MOBIL CORPORATION AND ITS AFFILIATED COMPANIES
ARE NOT FORMULATED TO CONTAIN PCBS.
Health studies have shown that many hydrocarbons pose potential human
health risks which may vary from person to person. Information provided
on this MSDS reflects intended use. This product should not be used for
other applications. In any case, the following advice should be
considered:
INJECTION INJURY WARNING: If product is injected into or under the skin,
or into any part of the body, regardless of the appearance of the wound
or its size, the individual should be evaluated immediately by a
physician as a surgical emergency. Even though initial symptoms from
high pressure injection may be minimal or absent, early surgical
treatment within the first few hours may significantly reduce the
ultimate extent of injury.
Precautionary Label Text:
CAUTION!
Exposure to oil mist may result in eye and skin irritation. Excessive
exposure to mists may cause respiratory irritation and damage.
Keep container closed. Use with adequate ventilation.
FIRST AID: If inhaled and symptoms develop, remove to fresh air and get
medical attention.
For industrial use only. Not intended or suitable for use in or around a
household or dwelling.
Refer to product Material Safety Data Sheet for further safety and health
information.
-------------------------------------------------------------------------
*************************************************************************
For Internal Use Only: MHC: 1* 1* 1* 1* 1*, MPPEC: A, TRN: 603183-00,
ELIS: 400325, CMCS97: 970924, REQ: US - MARKETING, SAFE USE: L
EHS Approval Date: 21OCT2002
*************************************************************************
Information given herein is offered in good faith as accurate, but
without guarantee. Conditions of use and suitability of the product for
particular uses are beyond our control; all risks of use of the product
are therefore assumed by the user and WE EXPRESSLY DISCLAIM ALL
WARRANTIES OF EVERY KIND AND NATURE, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO THE
USE OR SUITABILITY OF THE PRODUCT. Nothing is intended as a
recommendation for uses which infringe valid patents or as extending
license under valid patents. Appropriate warnings and safe handling
procedures should be provided to handlers and users. Alteration of this
document is strictly prohibited. Except to the extent required by law,
republication or retransmission of this document, in whole or in part, is
not permitted. Exxon Mobil Corporation and its affiliated companies
assume no responsibility for accuracy of information unless the document
is the most current available from an official ExxonMobil distribution
system. Exxon Mobil Corporation and its affiliated companies neither
represent nor warrant that the format, content or product formulas
contained in this document comply with the laws of any other country
except the United States of America.
Prepared by: ExxonMobil Oil Corporation
Environmental Health and Safety Department, Clinton, USA
|