Gazette
Commonwealth
of Australia
No. C 08, Tuesday, 2 August 2005
CHEMICAL
Published by the Commonwealth of Australia
?Commonwealth of Australia 2004
ISBN 1035-9877
This work is copyright. Apart from any use as permitted under the Copyright Act 1968, no part may be reproduced by any
process without prior written permission from the Commonwealth available from the Australian Government Department of
Communications, Information Technology and the Arts. Requests and inquiries concerning reproduction and rights should
be addressed to:
The Commonwealth Copyright Administration
Intellectual Property Branch
Department of Communications, Information Technology and the Arts
GPO Box 2154
Canberra ACT 2601
Or posted at: http://www.dcita.gov.au/cca
The Industrial Chemicals (Notification and Assessment) Act 1989 (the Act) commenced on
17 July 1990. As required by Section 5 of the Act, a Chemical Gazette is published on the
first Tuesday in any month or on any days prescribed by the regulations.
CONTENTS
SPECIAL NOTICES
1 DRAFT PRIORITY EXISTING CHEMICAL (PEC) REPORT FOR 5
TRIS(2,3-DIBROMOPROPYL) PHOSPHATE (TBPP)
6
2 SUMMARY OF DATA COLLECTED BY NICNAS ON CHEMICALS
INCLUDED IN THE ROTTERDAM CONVENTION ON PRIOR
INFORMED CONSENT (PIC) PROCEDURE FOR CERTAIN
HAZARDOUS CHEMICALS AND PESTICIDES IN
INTERNATIONAL TRADE
8
3 PUBLIC COMMENT SOUGHT ON THE PROPOSED
AMENDMENTS TO THE ADOPTED NATIONAL EXPOSURE
STANDARDS FOR ATMOSPHERIC CONTAMINANTS IN THE
OCCUPATIONAL ENVIRONMENT [NOHSC:1003(1995)] :
NOTATIONS RELATING TO SENSITISATION AND CARCINOGEN
CLASSIFICATIONS
4 THREE POLYBROMINATED FLAME RETARDANTS AS 9
PRIORITY EXISTING CHEMICALS
5 PRIORITY EXISTING CHEMICAL PROGRAM - CALL FOR 10
INFORMATION
6 CANDIDATE LIST OF CHEMICALS 11
NEW CHEMICALS
SUMMARY REPORTS
7 LTD/1139 M-1114 15
8 LTD/1155 POLYMER IN BYK-9077 18
9 LTD/1182 POLYMER IN DOBECKAN FT 2015 20
10 LTD/1189 POLYMER IN E7844 22
11 LTD/1201 HME-313 24
12 STD/1073 SYNACTO-976 26
29
13 STD/1138 COMPONENT 1 OF XC6170
14 STD/1139 COMPONENT 2 OF XC6170 32
15 STD/1140 COMPONENT 3 OF XC6170 35
16 STD/1141 COMPONENT 1 OF OLOA 249S 38
17 STD/1142 COMPONENT 2 OF OLOA 249S 41
18 STD/1145 POLYMER IN XC 1367 44
46
19 PLC/543 7-OXABICYCLO[4.1.0]HEPTANE-3-
CARBOXYLIC ACID, 7-
OXABICYCLO[4.1.0]HEPT-3-YLMETHYL
ESTER, POLYMER WITH ETHENYLBENZENE
AND 2-PROPENENITRILE
20 PLC/557 KP-1 48
21 PLC/558 RKP-02 50
22 PLC/592 POLYMER IN UROTUF F97-MPW-33 52
23 EX/72 U915 55
24 ACCESS TO FULL PUBLIC REPORT 58
PERMITS ISSUED
59
25 COMMERCIAL EVALUATION CATEGORY PERMITS
26 EARLY INTRODUCTION PERMITS 61
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES
62
27 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES FIVE
YEARS AFTER ISSUING OF ASSESSMENT CERTIFICATES
64
28 NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING
ON THE AUSTRALIAN INVENTORY OF CHEMICAL
SUBSTANCES AFTER ISSUING OF ASSESSMENT
CERTIFICATES
5
1 DRAFT PRIORITY EXISTING CHEMICAL (PEC) REPORT FOR TRIS(2,3-
DIBROMOPROPYL) PHOSPHATE (TBPP)
The draft PEC assessment report on Tris(2,3-dibromopropyl) phosphate was released to the
applicant for corrections under Section 60D of the Industrial Chemicals (Notification and
Assessment) Act 1989 (the Act), as amended. No corrections were received during this stage
which ended on 28 July 2005. However, significant additional information on use of TBPP
has been provided to the Director late in the Corrections Stage. The PEC report will be
released for Public Comment in September 2005, following the incorporation of the
additional information.
For further information please contact Dr Marie Verghis on (02) 8577 8848, Fax (02) 8577
8888 or email marie.verghis@nicnas.gov.au.
Review & Treaties
NICNAS
GPO Box 58
Sydney NSW 2001
Australia
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
6
2 SUMMARY OF DATA COLLECTED BY NICNAS ON CHEMICALS
INCLUDED IN THE ROTTERDAM CONVENTION ON PRIOR INFORMED
CONSENT (PIC) PROCEDURE FOR CERTAIN HAZARDOUS CHEMICALS AND
PESTICIDES IN INTERNATIONAL TRADE
The Director of NICNAS recently sought information under section 100G of the Industrial
Chemicals (Notification and Assessment) Act 1989 (the Act) on two chemicals 璽etramethyl
lead (CAS No. 75-74-1) and tetraethyl lead (CAS No. 78-00-2) - that have been added to
Annex III of the Rotterdam Convention.
A notice calling for information was published in the Chemical Gazette of 1 February 2005.
Background information to the Rotterdam Convention may be accessed from the NICNAS
website at http://www.nicnas.gov.au/Treaties/Rotterdam_Convention.asp
Information obtained from responses to the section 100G Gazette Notice was supplemented
by information obtained by NICNAS from the Australian Customs Service regarding goods
that may contain the chemicals.
Below is a summary of the information collected.
Tetramethyl lead (CAS 75-74-1)
There was no reported import, export, or use of this chemical.
Tetraethyl lead (CAS 78-00-2)
Industry response to the section 100G Notice indicates that this chemical is used in aviation
fuel (`Avgas'), and motor sport racing fuel as an octane enhancer and anti-valve seat
recession additive for piston engines.
For the period 12 months prior 1 February 2005, the following yearly amounts were
submitted:
Approximately 250 tonnes of tetraethyl lead was imported as additive for use in the
production of Avgas. Concentration of tetraethyl lead in the final blended Avgas ranged from
0.55g/L to 2.08 g/L.
Avgas containing approximately 2.5 tonnes of tetraethyl lead, in concentrations ranging from
0.55g/L to 0.662g/L, was also imported. Most Avgas used in Australia is sourced from
Australian manufacturers, and import of avgas is an irregular occurrence. Avgas is available
in Australia from airfields, aviation distributors and a minor amount from motor vehicle
racing organizations. Avgas that was supplied to remote aboriginal communities under the
Comgas Scheme in 2003 has been replaced by a non-leaded, non-aromatic motor fuel.
Less than 100 kg of tetraethyl lead is also imported in motor racing fuel for use in car,
motorcycle and boats used in motor and water sports, and vintage cars. Concentrations of
tetraethyl lead in these products ranges from 1.19 ?1.64 g/L. Supply and use of leaded fuels
for motor racing sports is regulated under section 13 of the Fuel Quality Standard Act 2000.
Approvals granted under this Act expire on 30 June 2005, and management of access to and
supply of leaded fuel after this date is currently under review by the Department of the
Environment and Heritage.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
7
In addition, less than 50 kg of tetraethyl lead is imported in fuel additives for engines
designed for running on leaded fuel. Information from industry indicated that these products
are available to the public.
Approximately 18 tonnes of tetraethyl lead in Avgas was exported. Concentrations of
tetraethyl lead in the Avgas ranged from 0.55 g/L to 1.29 g/L. Avgas was exported to Papua
New Guinea, Taiwan, Japan, New Zealand, Phillipines, Malaysia, Guam, Saipan, Tahiti,
Noumea, New Caledonia, Fiji, Micronesia, Norfolk Island.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
8
3 PUBLIC COMMENT SOUGHT ON THE PROPOSED AMENDMENTS TO
THE ADOPTED NATIONAL EXPOSURE STANDARDS FOR ATMOSPHERIC
CONTAMINANTS IN THE OCCUPATIONAL ENVIRONMENT
[NOHSC:1003(1995)] : NOTATIONS RELATING TO SENSITISATION AND
CARCINOGEN CLASSIFICATIONS
The National Occupational Health and Safety Commission is releasing the following Public
Consultation Paper for public comment:
Proposed amendments to the Adopted National Exposure Standards for Atmospheric
?br>
Contaminants in the Occupational Environment [NOHSC:1003(1995)]: Notations
relating to sensitisation and carcinogen classifications.
The document is available free of charge from the NOHSC Website at:
http://www.nohsc.gov.au/PublicComment
Alternatively, if you wish to have a copy of the document sent to you, place your request by:
?Telephone to Freecall 1800 552 488 ?at the prompts speak slowly and clearly and
state your name and postal or email address; or
? Fax to (02) 6276 8733 ?mark your fax `Public Comment: Notations Relating to
Sensitisation and Carcinogen Classifications' and include your name and postal or
email address; or
? Email to Chemicals@dewr.gov.au ?place `Public Comment: Notations Relating to
Sensitisation and Carcinogen Classifications' in the subject line and include your
name and postal or email address in the body of the email.
NOHSC will revise the Adopted National Exposure Standards for Atmospheric Contaminants
in the Occupational Environment [NOHSC:1003(1995)] in light of public comment received
with the expectation that these amendments will be finalised during 2006.
Public comment closes on 31 October 2005.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
9
4 THREE POLYBROMINATED FLAME RETARDANTS AS PRIORITY
EXISTING CHEMICALS
Decabromodiphenyl ether (CAS No. 1163-19-5), hexabromocyclododecane (CAS No.
25637-99-4 & 3194-55-6) and tetrabromobisphenol A (CAS No. 79-94-7) were declared
Priority Existing Chemicals (PECs) for full risk assessment on 7 June 2005. The declaration
notices can be accessed at:
http://www.nicnas.gov.au/Publications/Chemical_Gazette/chemgazettejun2005.asp
All those who wish to manufacture or import decabromodiphenyl ether (deca-BDE),
hexabromocyclododecane or tetrabromobisphenol A during the period that these are PECs
must apply in writing using the PEC application form. Importers of products/mixtures
containing these chemicals must also apply for assessment. There are no application fees.
However, there is a penalty for manufacturing or importing a PEC without first applying for
assessment of the chemical. We would like to thank those who have already applied for
assessment and have provided the required information as set out in the declaration notices.
This notice is a reminder that the closing date for provision of information is 26 August
2005.
The declaration notice for deca-BDE also covers its degradation products
pentabromodiphenyl ether (CAS No. 32534-81-9) and octabromodiphenyl ether (CAS No.
32536-52-0). The information provision requirements in the deca-BDE notice also apply to
its degradation products pentabromodiphenyl ether (penta-BDE) and octabromodiphenyl
ether (octa-BDE). NICNAS will conduct full risk assessments of penta-BDE and octa-BDE
ether along with deca-BDE. NICNAS recommends those manufacturing or importing penta-
BDE or octa-BDE also apply for assessment and provide the required information.
For further information or assistance, please contact Dr Janith Wickramaratna on (02) 8577
8846 or fax (02) 8577 8888 or email: janith.wickramaratna@nicnas.gov.au
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
10
5 PRIORITY EXISTING CHEMICAL PROGRAM -
CALL FOR INFORMATION
In accordance with Section 48 of the Industrial Chemicals (Notification and Assessment) Act
1989 (the Act), the Director is seeking information on uses of and potential exposure to
polyhexanide (technical grade) CAS no. 27083-27-8 due to potential health concerns.
Please note, this notice is in addition to the call for information on polyhexanide, CAS no.
32289-58-0, that was published in 5 July Chemical Gazette.
This notice is directed to all persons who have manufactured or imported the chemical or
products containing the chemical during the past 18 months. Any other persons with
information on this chemical, including users, past importers or manufacturers, are
encouraged to provide this information to the Director.
Chemical Name Other Names CAS Number
Poly(iminocarbonimidoyliminocarbonimidoyli Polyhexanide; 27083-27-8
mino-1,6-hexanediyl), hydrochloride Polihexanide
The following specific information is sought for this chemical for the calendar year 2004 to
the present:
Estimate of the total quantity (tonnes/year) of polyhexanide imported to Australia (in
?br>
raw form or in products) and/or manufactured in Australia; and
Uses of polyhexanide or the products containing the chemical, the concentration of
?br>
polyhexanide in products and whether any products are available to the public.
Responses regarding this chemical are required by 1 September, 2005. In accordance with
section 50 of the Act, the information may be accompanied by an application that some or all
of the information provided be treated as `exempt information'. Application forms may be
obtained from Ms Virginia Parish on 02 8577 8893 or downloaded from the Existing
Chemicals forms section of the NICNAS website at http://www.nicnas.gov.au/forms/.
Information collected by NICNAS may be provided to State, Territory or Commonwealth
regulatory agencies for the purposes of monitoring compliance under relevant legislation. All
information collected is treated in accordance with strict confidentiality guidelines and in
compliance with the Privacy Act 1988.
If you would like any further information, please contact Virginia Parish on
02 8577 8893.
Information is to be sent to Virginia Parish
Existing Chemicals
NICNAS
GPO Box 58
Sydney NSW 2001
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
11
6 CANDIDATE LIST OF CHEMICALS
The Candidate List of chemicals along with the Standby section of the List has been reviewed
and updated as of July 2005.
Chemicals contained in the standby section of the Candidate List were reviewed to determine
whether the awaited data has become available. Where new information has come to hand
this has been reviewed and the status of all the chemicals on the List redetermined. Two (2)
new nominations (Polyvinyl chloride and Iron pentacarbonyl) were received and have been
screened. Polyvinyl chloride met the selection criteria and has been added to the Candidate
List. Iron pentacarbonyl did not meet the selection criteria and a summary of the information
on this chemical is provided in Attachment 1.
Table 1 gives the Candidate List of chemicals following the review of the standby section.
The Candidate List will be used by NICNAS as a basis for selecting chemicals from time to
time for declaration and assessment as priority existing chemicals.
Table 2 gives the chemicals remaining on the Standby section of the List following the
review. This list will be reviewed periodically and chemicals transferred to the main section
of the Candidate List or the Not Selected List depending on the outcomes of awaited
assessments and/or testing.
Table 3 lists the chemicals moved from the main or standby sections of the Candidate List in
the current review and the reasons for the change.
Table 1: Candidate List of Chemicals
Chemical CAS No
Various Azo dyes Not assigned
Alkyl phenol ethoxylates (including the
specific chemicals listed):
Nonyl phenol ethoxylate 9016-45-9
Nonyl phenol ethoxylate blend 63496-57-1
Octylphenolethoxylate 9036-19-5
1,3 butadiene 106-99-0
Bismuth oxychloride 7787-59-9
t-butyl alcohol 75-65-0
Carbon disulphide 75-15-0
N,N Dimethylformamide 68-12-2
Epichlorohydrin 106-89-8
Ethylene oxide 75-21-8
di(2-ethylhexyl) adipate 103-23-1
Hydroquinone 123-31-9
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
12
Isocyanates (including the specific
chemicals listed):
2,4 TDI 584-84-9
2,4'-MDI 5873-54-1
2,6-TDI 91-08-7
4,4'-MDI 101-68-8
Polymethylene polyphenylene 9016-87-9
isocyanate
Isopropyl alcohol 67-63-0
Mercury compounds
Methyl ethyl ketone peroxide 1338-23-4
Methyl ethyl ketone 78-93-3
Methyl methacrylate 80-62-6
Methyl tert butyl ether 1634-04-4
Methylene chloride 75-09-2
N-methyl pyrrolidone 872-50-4
Naphthalene 91-20-3
Peracetic acid 79-21-0
Phenolphthalein 77-09-8
Phthalates (including the specific chemicals
listed):
diethylhexyl phthalate (DEHP) 117-81-7
Diethylphthalate (DEP) 84-66-2
Dibutylphthalate 84-74-2
di isodecyl phthalate (DIDP) 26761-40-0
di isononyl phthalate (DINP) 28553-12-0
butylbenzyl phthalate (BBP) 85-68-7
dimethyl phthalate (DMP) 131-11-3
dicyclohexyl phthalate 84-61-7
di-n-hexyl phthalate 84-75-3
di-n-pentyl phthalate 131-18-0
di-n-propyl phthalate 131-16-8
Polyvinyl acetate 9003-20-7
Sodium hydroxide 1310-73-2
Sodium hypochlorite 7681-52-9
Styrene 100-42-5
1,1,1,2-tetrafluoroethane 811-97-2
Tetrafluoroethylene 116-14-3
Toluene 108-88-3
Triethanolamine 102-71-6
Triethylene tetramine 112-24-3
Xylene ?mixed isomers 1330-20-7
o-xylene 95-47-6
p-xylene 106-42-3
m-xylene 108-38-3
Table 2: Standby Section of Candidate List
Chemical CAS No
Chromium (VI) compounds (including the
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
13
specific chemicals listed):
Lead chromate 7758-97-6
Lead sulphochromate 1344-37-2
Zinc chromate 13530-65-9
1-Naphthalenamine 134-32-7
1-Naphthalenamine, N-phenyl 90-30-2
2-Naphthalenamine 91-59-8
2-Naphthalenamine, N-phenyl 135-88-6
Tricresol phosphate 1330-78-5
Nickel 7440-02-0
Nickel oxide 1313-99-1
Nickel sulfate 7786-81-4
Table 3: Chemicals Moved from Main or Standby Sections of the Candidate List as of
July 2005
Chemical CAS No Moved Reason
from
di(2-ethylhexyl) adipate 103-23-1 Standby NIEHS report
section published.
Main Awaiting completion
Chromium (VI) compounds
section of a 2-year toxicity
(including the specific
and carcinogenicity
chemicals listed):
studies of hexavalent
chromium in rats and
mice.
Lead chromate 7758-97-6 Main Awaiting completion
section of a 2-year toxicity
and carcinogenicity
studies of hexavalent
chromium in rats and
mice.
Lead sulphochromate 1344-37-2 Main Awaiting completion
section of a 2-year toxicity
and carcinogenicity
studies of hexavalent
chromium in rats and
mice.
Zinc chromate 13530-65- Main Awaiting completion
9 section of a 2-year toxicity
and carcinogenicity
studies of hexavalent
chromium in rats and
mice.
Naphthalene 91-20-3 Standby Final report of EU
section Risk Assessment
Report published.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
14
Attachment 1
IRON PENTACARBONYL
CAS Number
13463-40-6
Reasons for Nomination
The chemical was nominated by a member of the public due to concerns about toxic effects
of exposure to iron in high doses
Import, Manufacture & Use
The chemical was subject to a call for information under S48 of the Act. No data from
industry was received. According to published literature, uses for the chemical include:
To make carbonyl iron which is used to make high frequency coils for radio and television.
As an antiknock agent in motor fuels
As a catalyst and reagent in chemical reactions
Databases Searched
During screening of chemicals nominated by the public background work done by NICNAS
included a search of websites of overseas regulatory agencies, the TOMES CPS database,
Exichem and OECD databases. The searches indicated that the chemical has not been
evaluated by any overseas agency, or that any work has been undertaken or is underway in
the OECD Existing Chemicals Program.
Information on the Chemical
The chemical is supplied as an oily yellow liquid. Studies in rats showed a medium acute
toxicity and dermal toxicity in rabbits was low. The chemical was a lung irritant in animals
and repeated exposure to rats caused severe lung effects. In humans, high concentrations have
been reported to have caused headaches, dizziness, fever, cyanosis, respiratory and central
nervous system effects, kidney and liver damage. Iron pentacarbonyl has an occupational
exposure standard assigned of 0.23 mg/m3 TWA and 0.45 mg/m3 STEL.
Reasons for Non-Selection
As far as NICNAS could determine, iron pentacarbonyl is not used in Australia. The
chemical did not meet the published screening criteria for prioritisation of nominated
chemicals.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
15
7 PUBLICATION SUMMARY REPORT
M-1114
Summary Report
Reference No: LTD/1139
Ilford Imaging Asia Pacific Pty Ltd (ABN 69 004 283 701) of Unit 1, 10 Duerdin Street
Clayton North VIC 3149. has submitted a limited notification statement in support of their
application for an assessment certificate for M-1114. The notified polymer is intended to be
used as a component in printing ink. Up to 1 tonnes of the notified chemical will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
? Irritant (Xi): R36/ 38 (Irritating to eyes and skin).
As a comparison only, the classification of notified chemical using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) (United Nations, 2003) is
presented below. This system is not mandated in Australia and carries no legal status but is
presented for information purposes.
Hazard Hazard statement
category
Skin irritation 3 Causes mild skin irritation
Eye irritation 2A Causes serious eye irritation
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health based on its reported use pattern.
Environmental Effects
On the basis of the PEC/PNEC ratio:
? The chemical is not considered to pose a risk to the environment based on its reported
use pattern.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
16
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- Irritant (Xi): R36/ 38 (Irritating to eyes and skin).
? Use the following risk phrases for products/mixtures containing the notified chemical:
- Concentration cut-off 20%: R36/ 38 (Irritating to eyes and skin).
Control Measures
Occupational Health and Safety
No special precautions are required for the notified chemical when used at low quantities in
inkjet printer cartridges. However, in the interests of good occupational health and safety, the
following guidelines and precautions should be observed:
? Personnel should wear cotton or disposable gloves when servicing printers and
refilling cartridges.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? Avoid contact with the eyes and skin.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
Disposal
? The notified chemical should be disposed of by incineration or landfill.
Emergency procedures
? No special precaution necessary (cartridges).
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
17
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical;
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
18
8 PUBLICATION SUMMARY REPORT
Polymer in BYK-9077
Summary Report
Reference No: LTD/1155
Nuplex Industries (Australia) Pty Ltd (ABN 25 000 045 572) of 49-61 Stephen Road Botany
NSW 2019, Degussa Coatings & Colourants Pty Ltd (ABN 16 079 823 313) 30 Commercial
Drive Dandenong VIC 3175, and Clariant (Australia) Pty Ltd (ABN 30 069 435 552) 675
Warrigal Road Chadstone VIC 3148 have submitted a limited notification statement in
support of their application for an assessment certificate for Polymer in BYK-9077. The
notified polymer is intended to be used as a component of printing ink and paint products for
industrial and general coating applications. Thirty to fifty tonnes tonnes of the notified
polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified polymer is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
As a comparison only, the classification of notified polymer using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) is presented below. This
system is not mandated in Australia and carries no legal status but is presented for
information purposes.
Based on the available data, the notified chemical does not meet the criteria for the
Classification and Labelling of Chemicals according to the United Nations Globally
Harmonised System.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as a component of printing ink and
paint products in the pattern described.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
patterns.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
19
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced.
?S24 Avoid contact with skin
?S25 Avoid contact with eyes
?S37 Wear suitable gloves
?S39 Wear suitable eye/face protection
? No specific engineering controls or personal protective equipment are required for the
safe use of the notified chemical as introduced (<5% in product), however, these
should be selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by incineration, recycling or landfill.
Emergency procedures
? Place inert, non-combustible absorbent such as vermiculite, sand or soil onto material.
Collect the material and place in suitable labelled containers.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- uses are proposed which will result in more significant release to the aquatic
compartment, a secondary notification should be submitted with results and reports
for aquatic toxicity, since this is estimated to be high.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
20
9 PUBLICATION SUMMARY REPORT
Polymer in Dobeckan FT 2015
Summary Report
Reference No: LTD/1182
Siemens Ltd (ABN 98 004 347 880) of 885 Mountain Highway, Bayswater, VIC 3153 has
submitted a limited notification statement in support of their application for an assessment
certificate for Polymer in Dobeckan FT 2015. The notified polymer is intended to be used as
electric insulating resin for impregnating electrical windings. Three tonnes of the notified
polymer will be imported in the first year followed by 500 kg per annum for each of the next
four years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as described in the notification.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified polymer as introduced in the product [Dobeckan
FT 2015]:
- Exhaust ventilation when the containers are opened and the product containing the
notified polymer poured into treating chambers, and when impregnating electrical
windings.
- Enclosed system when impregnating electrical windings.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer as introduced:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
21
- Protective gloves,
- safety glasses or goggles,
- half-facepiece respirator and
- industrial clothing
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
? Do not allow the polymer/resin to enter sewer or containers to contaminate drains or
waterways or sewer.
Disposal
? Wastes generated during industrial application should be disposed of through a
licensed waste contractor or consigned to landfill.
Emergency procedures
? Spills/release of the notified polymer should be handled by qualified personnel. Do
not flush into surface water or sanitary sewer system. Take up mechanically or with
an adsorbent material, either sand, diatomaceous earth, universal adsorbent or saw
dust and dispose of appropriately.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
22
10 PUBLICATION SUMMARY REPORT
Polymer in E7844
Summary Report
Reference No: LTD/1189
Afton Chemical Asia Pacific LLC (ABN 99 109 644 288) of Level 9, 20 Berry Street, North
Sydney NSW 2059 has submitted a limited notification statement in support of their
application for an assessment certificate for Polymer in E7844. The notified polymer is
intended to be used as an additive in automotive fuels. Up to 300 tonnes of the notified
polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified polymer is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
R38: Irritating to skin
?br>
As a comparison only, the classification of notified polymer using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) (United Nations 2003) is
presented below. This system is not mandated in Australia and carries no legal status but is
presented for information purposes.
Hazard category Hazard statement
Skin corrosion/ irritation 2 Irritant Causes skin irritation
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used as a fuel additive.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
23
- R38 Irritating to skin
? Use the following risk phrases for products/mixtures containing the notified chemical:
- > 20%: R38 Irritating to skin
Control Measures
Occupational Health and Safety
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer as introduced in
the product E7844:
- Chemical-resistant gloves, chemical goggle or face shields, and long sleeves.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of by incineration.
Emergency procedures
? Spills/release of the notified polymer should be soaked up with inert material and
placed in labelled containers for recycling or disposal by incineration.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within
28 days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
24
11 PUBLICATION SUMMARY REPORT
HME-313
Summary Report
Reference No: LTD/1201
Ricoh Australia Pty Ltd (ABN: 30 000 593 171) of 8 Rodborough Rd, Frenchs Forest, NSW
2086 has submitted a limited notification statement in support of their application for an
assessment certificate for HME-313. The notified chemical is intended to be used as a
component of printing ink. Less than one tonne of the notified chemical will be imported per
annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used in the proposed manner.
Environmental Effects
On the basis of the PEC/PNEC ratio of 9 x 10-5, the chemical is not considered to pose a risk
to the environment based on its reported use pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? A copy of the MSDS should be easily accessible to employees.
? Service personnel should wear cotton or disposable gloves and ensure adequate
ventilation is present when removing spent printer cartridges containing the notified
polymer and during routine maintenance and repairs.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
25
Disposal
? The notified chemical should be disposed of by thermal decomposition in high
temperature incinerators or to secure landfill.
Emergency procedures
? Spills/release of the notified chemical should be handled by physical containment and
collection using absorbent material, with subsequent disposal by thermal
decomposition in high temperature incinerators or to secure landfill.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical; or
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
26
12 PUBLICATION SUMMARY REPORT
Synacto 976
Summary Report
Reference No: STD/1073
Infineum Australia Pty Ltd (ABN 24 084 881 863) of Level 2, 6 Riverside Quay, Southbank
VIC 3006 has submitted a standard notification statement in support of their application for
an assessment certificate for Synacto 976. The notified chemical is intended to be used as an
antioxidant/anticorrosion additive component in the formulation of emulsifiable cutting oil
concentrates for use in mines and other metalworking industries. Up to 300 tonnes of the
notified chemical as a concentrated mineral oil based product will be imported per annum for
each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as a hazardous substance
under the NOHSC Approved Criteria for Classifying Hazardous Substances.
As a comparison only, the classification of notified chemical using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) (United Nations 2003) is
presented below. This system is not mandated in Australia and carries no legal status but is
presented for information purposes.
The notified chemical is not classified under the Globally Harmonised System of
Classification and Labelling of Chemicals (GHS) for both health and environmental hazards.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner
Environmental Effects
On the basis of the PEC/PNEC ratio, the chemical is considered to pose an acceptable risk to
the environment based on its reported use pattern
RECOMMENDATIONS
Control Measures
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical introduced as a mineral oil-based
product:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
27
- Use of closed systems at the blending and packaging sites, including enclosed and
automatic transfer lines/pumps for loading and emptying of transport drums and
mixing vessels;
- Adequate ventilation for the plant operators.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical during reformulation
and end use:
- Adequate training for staff in handling lubricant and oil products;
- Implementation of general health surveillance and monitoring programs as required
including any potential for skin sensitisation.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical during
reformulation and end use:
- Chemical goggles/face shields for plant operators;
- Industrial standard protective clothing and impermeable gloves for plant operators and
metalworking workers;
- Vapour masks or appropriate respirators if required.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of either by recycling, burning, refining or
incineration.
Emergency procedures
? Spills/release of the notified chemical should be handled by containment with suitable
absorbents (eg sand or earth), collection and storage in a sealable and labelled
container for recycle or disposal in accord with local regulations.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
28
Under Section 64(1) of the Act; if
- Import volume exceeds 300 tonnes per annum, it is required a better set of
physiochemical data for the notified chemical, a better estimate of release to the
sewer, particularly in the rural areas, and an acute toxicity test report for algae be
submitted for review and assessment.
- Additional skin sensitisation information/studies on and adverse effects of the notified
chemical have become available.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
29
13 PUBLICATION SUMMARY REPORT
Component 1 of XC6170
Summary Report
Reference No: STD/1138
Chevron Oronite Australia (ABN: 16 101 548 716) of Level 8, 520 Collins St, Melbourne,
Victoria, 3000 has submitted a standard notification statement in support of their application
for an assessment certificate for Component 1 of XC6170. The notified chemical is intended
to be used as a lubricant additive. Up to 100 tonnes of the notified chemical will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
? R43 ?May cause sensitisation by skin contact
? R38 ?Irritating to skin
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described, based on the expected low exposure.
Public Health
There is High Concern to public health when used as a lubricant additive due to the
hazardous nature and proposed use patterns.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R43 May cause sensitisation by skin contact
- R38 Irritating to skin
? Use the following risk phrases for products/mixtures containing the notified chemical:
- >1% R43 May cause sensitisation by skin contact
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
30
- >20% R38 Irritating to skin
? The National Drugs and Poisons Standing Committee (NDPSC) should consider the
notified chemical for listing on the SUSDP.
? Products containing more than 1% notified chemical and available to the public
should carry the following safety phrases on the label:
- S2 Keep out of reach of children
- S24 Avoid contact with skin
- S36 Wear suitable protective clothing
- S37 Wear suitable gloves
Control Measures
Occupational Health and Safety
? Employers should implement the following safe practices to minimise occupational
exposure during handling of the notified chemical as introduced:
- Minimise spills and drips
- Where possible, automated processes should be used to reduce worker contact
- Use closed systems for reformulation
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use in the lubricant product:
- Chemical resistant gloves
- Protective clothing
- Safety goggles
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by landfill or incineration.
Emergency procedures
? Contain release to prevent further contamination of soil, surface water or
groundwater. Clean up spillage as soon as possible by applying non-combustible
absorbent materials (small spills) or pumping (large spills). Remove contaminated soil
and place contaminated material in disposable containers.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
31
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
32
14 PUBLICATION SUMMARY REPORT
Component 2 of XC6170
Summary Report
Reference No: STD/1139
Chevron Oronite Australia (ABN: 16 101 548 716) of Level 8, 520 Collins St, Melbourne,
Victoria, 3000 has submitted a standard notification statement in support of their application
for an assessment certificate for Component 2 of XC6170. The notified chemical is intended
to be used as a lubricant additive. Up to 100 tonnes of the notified chemical will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
? R43 ?May cause sensitisation by skin contact
? R38 ?Irritating to skin
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described, based on the expected low exposure.
Public Health
There is High Concern to public health when used as a lubricant additive due to the
hazardous nature and proposed use patterns.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R43 May cause sensitisation by skin contact
- R38 Irritating to skin
? Use the following risk phrases for products/mixtures containing the notified chemical:
- >1% R43 May cause sensitisation by skin contact
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
33
- >20% R38 Irritating to skin
? The National Drugs and Poisons Standing Committee (NDPSC) should consider the
notified chemical for listing on the SUSDP.
? Products containing more than 1% notified chemical and available to the public
should carry the following safety phrases on the label:
- S2 Keep out of reach of children
- S24 Avoid contact with skin
- S36 Wear suitable protective clothing
- S37 Wear suitable gloves
Control Measures
Occupational Health and Safety
? Employers should implement the following safe practices to minimise occupational
exposure during handling of the notified chemical as introduced:
- Minimise spills and drips
- Where possible, automated processes should be used to reduce worker contact
- Use closed systems for reformulation
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use in the lubricant product:
- Chemical resistant gloves
- Protective clothing
- Safety goggles
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by landfill or incineration.
Emergency procedures
? Contain release to prevent further contamination of soil, surface water or
groundwater. Clean up spillage as soon as possible by applying non-combustible
absorbent materials (small spills) or pumping (large spills). Remove contaminated soil
and place contaminated material in disposable containers.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
34
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
35
15 PUBLICATION SUMMARY REPORT
Component 3 of XC6170
Summary Report
Reference No: STD/1140
Chevron Oronite Australia (ABN: 16 101 548 716) of Level 8, 520 Collins St, Melbourne,
Victoria, 3000 has submitted a standard notification statement in support of their application
for an assessment certificate for Component 3 of XC6170. The notified chemical is intended
to be used as a lubricant additive. Up to 100 tonnes of the notified chemical will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
? R43 ?May cause sensitisation by skin contact
? R38 ?Irritating to skin
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described, based on the expected low exposure.
Public Health
There is High Concern to public health when used as a lubricant additive due to the
hazardous nature and proposed use patterns.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R43 May cause sensitisation by skin contact
- R38 Irritating to skin
? Use the following risk phrases for products/mixtures containing the notified chemical:
- >1% R43 May cause sensitisation by skin contact
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
36
- >20% R38 Irritating to skin
? The National Drugs and Poisons Standing Committee (NDPSC) should consider the
notified chemical for listing on the SUSDP.
? Products containing more than 1% notified chemical and available to the public
should carry the following safety phrases on the label:
- S2 Keep out of reach of children
- S24 Avoid contact with skin
- S36 Wear suitable protective clothing
- S37 Wear suitable gloves
Control Measures
Occupational Health and Safety
? Employers should implement the following safe practices to minimise occupational
exposure during handling of the notified chemical as introduced:
- Minimise spills and drips
- Where possible, automated processes should be used to reduce worker contact
- Use closed systems for reformulation
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use in the lubricant product:
- Chemical resistant gloves
- Protective clothing
- Safety goggles
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by landfill or incineration.
Emergency procedures
? Contain release to prevent further contamination of soil, surface water or
groundwater. Clean up spillage as soon as possible by applying non-combustible
absorbent materials (small spills) or pumping (large spills). Remove contaminated soil
and place contaminated material in disposable containers.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
37
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
38
16 PUBLICATION SUMMARY REPORT
Component 1 of OLOA 249S
Summary Report
Reference No: STD/1141
Chevron Oronite Australia (ABN: 16 101 548 716) of Level 8, 520 Collins St, Melbourne,
Victoria, 3000 has submitted a standard notification statement in support of their application
for an assessment certificate for Component 1 of OLOA 249S. The notified chemical is
intended to be used as a lubricant additive. Up to 100 tonnes of the notified chemical will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
? R43 ?May cause sensitisation by skin contact
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described, based on the expected low exposure.
Public Health
There is High Concern to public health when used as a lubricant additive due to the
hazardous nature and proposed use patterns.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R43 May cause sensitisation by skin contact
? Use the following risk phrases for products/mixtures containing the notified chemical:
- >1% R43 May cause sensitisation by skin contact
? The National Drugs and Poisons Standing Committee (NDPSC) should consider the
notified chemical for listing on the SUSDP.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
39
? Products containing more than 1% notified chemical and available to the public
should carry the following safety phrases on the label:
- S2 Keep out of reach of children
- S24 Avoid contact with skin
- S36 Wear suitable protective clothing
- S37 Wear suitable gloves
Control Measures
Occupational Health and Safety
? Employers should implement the following safe practices to minimise occupational
exposure during handling of the notified chemical as introduced:
- Minimise spills and drips
- Where possible, automated processes should be used to reduce worker contact
- Use closed systems for reformulation
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use in the lubricant product:
- Chemical resistant gloves
- Protective clothing
- Safety goggles
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by landfill or incineration.
Emergency procedures
? Contain release to prevent further contamination of soil, surface water or
groundwater. Clean up spillage as soon as possible by applying non-combustible
absorbent materials (small spills) or pumping (large spills). Remove contaminated soil
and place contaminated material in disposable containers.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
40
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
41
17 PUBLICATION SUMMARY REPORT
Component 2 of OLOA 249S
Summary Report
Reference No: STD/1142
Chevron Oronite Australia (ABN: 16 101 548 716) of Level 8, 520 Collins St, Melbourne,
Victoria, 3000 has submitted a standard notification statement in support of their application
for an assessment certificate for Component 2 of OLOA 249S. The notified chemical is
intended to be used as a lubricant additive. Up to 100 tonnes of the notified chemical will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
? R43 ?May cause sensitisation by skin contact
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described, based on the expected low exposure.
Public Health
There is High Concern to public health when used as a lubricant additive due to the
hazardous nature and proposed use patterns.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R43 May cause sensitisation by skin contact
? Use the following risk phrases for products/mixtures containing the notified chemical:
- >1% R43 May cause sensitisation by skin contact
? The National Drugs and Poisons Standing Committee (NDPSC) should consider the
notified chemical for listing on the SUSDP.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
42
? Products containing more than 1% notified chemical and available to the public
should carry the following safety phrases on the label:
- S2 Keep out of reach of children
- S24 Avoid contact with skin
- S36 Wear suitable protective clothing
- S37 Wear suitable gloves
Control Measures
Occupational Health and Safety
? Employers should implement the following safe practices to minimise occupational
exposure during handling of the notified chemical as introduced:
- Minimise spills and drips
- Where possible, automated processes should be used to reduce worker contact
- Use closed systems for reformulation
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use in the lubricant product:
- Chemical resistant gloves
- Protective clothing
- Safety goggles
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by landfill or incineration.
Emergency procedures
? Contain release to prevent further contamination of soil, surface water or
groundwater. Clean up spillage as soon as possible by applying non-combustible
absorbent materials (small spills) or pumping (large spills). Remove contaminated soil
and place contaminated material in disposable containers.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
43
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
44
18 PUBLICATION SUMMARY REPORT
Polymer in XC 1367
Summary Report
Reference No: STD/1145
Chevron Oronite Australia (ABN: 16 101 548 716) of Level 8, 520 Collins St, Melbourne,
Victoria, 3000 has submitted a standard notification statement in support of their application
for an assessment certificate for Polymer in XC 1367. The notified polymer is intended to be
used as part of a lubricant additive package. Up to 25 tonnes of the notified polymer will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified polymer is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as a lubricant additive.
Environmental Effects
On the basis of the PEC/PNEC ratio the chemical is not considered to pose a risk to the
environment based on its reported use pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? A copy of the MSDS should be easily accessible to employees.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced or
as diluted for use:
- Avoid contact with eyes and skin
- Wear chemical resistant apron, jacket and rubber boots.
- Wear chemical resistant gloves
- Wear safety goggles
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
45
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical during reformulation
and end use:
- Implementation of general health surveillance and monitoring programs as required
including any potential for skin sensitisation.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
Environment
Disposal
? The notified chemical should be disposed of to landfill or be incinerated.
Emergency procedures
? Spills/release of the notified chemical should be handled by soaking up with inert
absorbent material and follow state or local regulation for the disposal of the waste.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
? Additional skin sensitisation information/studies on the notified chemical and adverse
effects of the notified chemical have become available.
or
Under Section 64(2) of the Act:
? if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
46
19 PUBLICATION SUMMARY REPORT
7-Oxabicyclo[4.1.0]heptane-3-carboxylic acid, 7-oxabicyclo[4.1.0]hept-3-
ylmethyl ester, polymer with ethenylbenzene and 2-propenenitrile
Summary Report
Reference No: PLC/543
GE Advanced Materials Plastics Pty Ltd, (ABN 92 005 837 454) of 175 Hammond Road
Dandenong, VIC 3175 has submitted a polymer of low concern (PLC) notification statement
in support of their application for an assessment certificate for 7-Oxabicyclo[4.1.0]heptane-3-
carboxylic acid, 7-oxabicyclo[4.1.0]hept-3-ylmethyl ester, polymer with ethenylbenzene and
2-propenenitrile. The notified polymer is used as polymer additive to modify surface
appearance. Less than 75 tonnes of the notified polymer will be imported per annum for each
of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
? The level of atmospheric nuisance dust should be maintained as low as possible. The
NOHSC exposure standard for atmospheric dust is 10 mg/m3.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
47
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of to landfill.
Emergency procedures
? Spills/release of the notified polymer should be handled by physical containment,
collection and disposal to landfill.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
48
20 PUBLICATION SUMMARY REPORT
KP-1
Summary Report
Reference No: PLC/557
Ricoh Australia Limited, (ABN 30 000 593 171) of 8 Rodborough Road, Frenchs Forest
NSW 2986 has submitted a polymer of low concern (PLC) notification statement in support
of their application for an assessment certificate for KP-1. The notified polymer is intended to
be used as used as a component of printing ink. Less than 1 tonne of the notified polymer will
be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
? Service personnel should wear cotton or disposable gloves when replenishing
developer and servicing copying machines and printers.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
49
- Use according to the manufacturer's instructions.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Public Health
? The following measures should be taken to minimise public exposure to the notified
polymer:
Do not swallow. Keep out of reach of children. Avoid contact with eyes
Environment
? Do not allow material or contaminated packaging to enter drains, sewers or water
courses.
Disposal
? The notified polymer should be disposed of in landfill or be destroyed through
incineration
Emergency procedures
? Spills/release of the notified polymer should be handled by collecting the cartridge
intact and landfilled.
?Contain the spill and absorb with sawdust, sand or earth.
?Place used absorbent in suitable sealed containers and follow state or local regulation
for the disposal of the waste.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
50
PUBLICATION SUMMARY REPORT
21
RKP-02
Summary Report
Reference No: PLC/558
Ricoh Australia Limited, (ABN 30 000 593 171) of 8 Rodborough Road, Frenchs Forest
NSW 2986 has submitted a polymer of low concern (PLC) notification statement in support
of their application for an assessment certificate for RKP-02. The notified polymer is
intended to be used as used as a component of printing ink. Less than 1 tonne of the notified
polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
? Service personnel should wear cotton or disposable gloves when replenishing
developer and servicing copying machines and printers.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
51
- Use according to the manufacturer's instructions.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Public Health
? The following measures should be taken to minimise public exposure to the notified
polymer:
Do not swallow. Keep out of reach of children. Avoid contact with eyes
Environment
? Do not allow material or contaminated packaging to enter drains, sewers or water
courses.
Disposal
? The notified polymer should be disposed of in landfill or be destroyed through
incineration
Emergency procedures
? Spills/release of the notified polymer should be handled by collecting the cartridge
intact and landfilled.
?Contain the spill and absorb with sawdust, sand or earth.
?Place used absorbent in suitable sealed containers and follow state or local regulation
for the disposal of the waste.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
52
22 PUBLICATION SUMMARY REPORT
Polymer in Urotuf F97-MPW-33
Summary Report
Reference No: PLC/592
DIC International (Australia) Pty. Ltd (ABN 17 003 441 067) of 30-32 Kilkenny Crt,
Dandenong South, VIC. 3175 has submitted a polymer of low concern (PLC) notification
statement in support of their application for a self-assessed assessment certificate for Polymer
in Urotuf F97-MPW-33. The notified polymer is intended to be used as a water borne paint
for wood and concrete coating. Paint formulation and application will occur in Australia. Up
to 50 tonnes of the notified polymer will be imported per annum for each of the first five
years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
The product Urotuf F97-MPW-33 is classified as hazardous to health according to the criteria
of NOHSC Approved Criteria for Classifying Hazardous Substances, as a result of the
additives 1-methyl-2-pyrrolidinone (NMP) and N,N-diethylethanamine.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
53
? A copy of the MSDS should be easily accessible to employees.
? Personal protective equipment required during formulation of the Urotuf F97-MPW-
33 product are:
- Eye protection (safety glasses or goggles)
- Impermeable gloves
- Industrial clothing and footwear
- Respirator with organic vapour cartridge when occupational exposure standards are
exceeded.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer as introduced and in
formulated paint products:
- Use of spray paints containing the notified polymer should be in accordance with the
NOHSC National Guidance Material for Spray painting.
Environment
? The following control measures should be implemented by the notifier to minimise
environmental exposure during formulation of the notified polymer:
- Bunding
? The following control measures should be implemented by end users (spray painters)
to minimise environmental exposure during use of the notified polymer:
- Exhaust ventilation with filter
Disposal
? The notified polymer should be disposed of to landfill or incinerated.
? Empty containers should be sent to local recycling or waste disposal facilities.
Emergency procedures
? Spills/release of the notified polymer should be handled by absorbing with sand and
put into suitable container for disposal. Contaminated containers can be re-used after
cleaning.
?The notified polymer should not be allowed to enter drains or waterways.
Storage
? If products and mixtures containing the notified polymer are classified dangerous
goods, dangerous goods storage requirements may apply.
Transport and Packaging
? If products and mixtures containing the notified polymer are classified dangerous
goods, dangerous goods transport and packaging requirements may apply.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
54
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
55
23 PUBLICATION SUMMARY REPORT
U915
Summary Report
Reference No: EX/72
Parchem Construction Products Pty Ltd (ABN 80 069 961 968) of 7 Lucca Road Wyong
NSW 2259 has submitted a synthetic polymer of low concern (PLC) notification statement in
support of their application for an assessment certificate for U915. The notified polymer is
intended to be used as a floor finish. Less than 20 tonnes of the notified chemical will be
imported per annum for each of the first five years.
Since granting of the abovementioned Assessment Certificate, Multichem Pty Ltd (ABN 47
006 115 886) of Suite 5, 400 High Street Kew VIC 3101 and Orica Australia Pty Ltd (ABN
99 004 117 828) of 1 Nicholson St Melbourne VIC 3000 have submitted a notification
statement in support of their application for an extension of the original Assessment
Certificate for U195. Company Parchem Construction Products Pty Ltd has agreed to this
extension. Information submitted by Orica Australia Pty Ltd pertains to the introduction of
notified chemical in the product Alberdingk Resin U-195 which will be used in water based
floor finishes/coating. The introduction volume will less than 35 tonnes per annum.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
No toxicological information has been provided for the notified polymer. However, due to
the high molecular weight and low reactivity, the notified polymer is expected to be of low
toxicity and not absorbed through the skin.
The imported polymer dispersion contains 9.6% N-methylpyrrolidone, which is a skin and
eye irritant, with a hazardous substance cut-off concentration of 10%. The polymer
dispersion is therefore expected to be a moderate eye and skin irritant.
Toxicological information on the material safety data sheet (MSDS) supplied for the final
product indicates that the product may cause moderate eye irritation and result in transient
corneal damage. In sensitive individuals, skin contact may cause dermatitis. Vapours from
the product in poorly ventilated areas may cause slight to moderate irritation to respiratory
tract. These effects are anticipated to be associated with the solvents present in the product,
rather than related to the notified polymer.
Occupational health and safety
There is little potential for occupational exposure to the notified polymer during transport and
storage or sale of the polymer emulsion or the finished product containing the polymer.
However, exposure to the notified polymer during reformulation, use and disposal is possible.
During the reformulation process, the main exposure route for the notified polymer will be
dermal. Inhalation exposure is not likely, as the emulsion contains 55% water and ready
formation of aerosols is not expected. Skin and eye irritation may occur during transfer of
the polymer dispersion to the mixing vessel and during the filling operation, however, the
engineering controls and personal protective equipment specified in the notification statement
(ventilation, impervious gloves, safety goggles and coveralls) are sufficient to provide
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
56
protection against the irritating effects. Therefore, the risk of adverse health effects arising
from contact with the notified polymer is expected to be very low.
Application of the floor finish by roller coating may lead to dermal exposure to the notified
polymer and the organic solvents present in the product. Inhalation exposure to organic
vapours is also possible. As exposure may be high and irritation of skin, eye and respiratory
tract may occur, workers should be protected from contamination with the end use product
during use. Once the applied coating has cured (dried in air), the polymer will not be
separately available for exposure or uptake.
Public health
The potential for public exposure to the notified polymer during all stages of its life cycle is
considered to be very low. Floor coating containing the notified polymer will not be sold to
the public. Once applied to the surface, the crosslinked polymer in the floor sealant hardens
and dries, and public exposure by dermal contact with the dried paint film is expected to be
negligible.
Based on the above information, it is considered that Alberdinkg Polyurethane Dispersion
U915 will not pose a significant hazard to public health when used in the proposed manner.
Environmental effects
The products containing the notified substance are likely to be used throughout Australia. The
major environmental exposure to the substance will come from disposal of the waste polymer
from the reformulation process and empty containers to landfill. This should be of low
hazard to the environment as the polymer will remain bound within the landfill soils and
sediments and slowly degrade by the abiotic processes.
The waste polymer produced during the application process is likely to be discharged in
domestic wash waters to waste water treatment systems. If it is assumed as a worst case
scenario that there is no removal of the polymer in the sewage treatment plant, the resultant
Predicted Environmental Concentration (PEC) in receiving waters was calculated to be 0.01
礸/mL.
The ecotoxicological data summarised in the polymer MSDS indicates that under normal use,
where release is dispersed all over Australia, it should be of low concern to aquatic
organisms. Adsorption to sludge, soil and sediment, and dilution in receiving waters should
reduce environmental concentrations to low levels.
Polymer spilt on land is expected to become immobilised in the soil layer. Contaminated soil
can then be collected and disposed to landfill. Polymer disposed to landfill either from spills,
the reformulation process or as drum residues which will similarly remain bound in the soil
and sediments.
Given the above, environmental exposure and the overall environmental hazard are expected
to be low.
RECOMMENDATIONS
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
57
To minimise occupational exposure to U 915, the following guidelines and precautions
should be observed:
? Protective eyewear, chemical resistant industrial clothing and footwear and
impermeable gloves should be used during occupational use of products containing
the notified polymer;
? Spillage of the notified chemical should be avoided. Spillages should be cleaned up
promptly with absorbents which should then be put into containers for disposal;
? A copy of the MSDS should be easily accessible to employees.
? If products containing the notified polymer are hazardous to health in accordance with
the NOHSC Approved Criteria for Classifying Hazardous Substances (NOHSC,
1999b), workplace practices and control procedures consistent with State and territory
hazardous substances regulations must be in operation.
Guidance in the selection, personal fit and maintenance of personal protective equipment can
be obtained from:
? Protective eyewear AS 1336; AS/NZS 1337
? Chemical impermeable clothing AS 3765.2.
? Impermeable gloves AS 2161.2.
? Occupational footwear AS/NZS 2210
? Respirators AS/NZS 1715 and AS/NZS 1716
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
58
24 ACCESS TO FULL PUBLIC REPORT
NICNAS publishes a Full Public Report for each new chemical assessed. These reports are
available for public inspection at the library of the National Occupational Health & Safety
Commission at their Canberra office by appointment only. Please call the library on (02)
6279 1161 or (02) 6279 1163 to arrange to view the Full Public Report.
Reports can also be viewed and downloaded free of charge from our website at
www.nicnas.gov.au. Copies of these reports may also be requested, free of charge, by
contacting the Administration Section of NICNAS by phone: (02) 8577 8816 or fax: (02)
8577 8888.
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
59
25 COMMERCIAL EVALUATION CATEGORY PERMIT
The permits listed in Table 1 were issued to import or manufacture the following chemicals
for commercial evaluation under section 21G of the Industrial Chemicals (Notification and
Assessment) Act 1989.
Table 1
Commercial Evaluation Category Permits
PERMIT COMPANY COMPANY CHEMICAL OR HAZARDO QUANTITY USE PERIOD
NUMBER NAME POSTCODE TRADE NAME US APPROVED
SUBSTANC
E
Yes 4000 kg Textile Dye 2 yrs
609 Ciba 3074 2,7-
Specialty Naphthalenedisu
Chemicals lfonic acid, 3-
Pty Ltd amino-4-[[4-[[4-
[[2-[2-
(ethenylsulfonyl
)ethoxy]ethyl]a
mino]-6-fluoro-
1,3,5-triazin-2-
yl]amino]-2-
sulfophenyl]azo]
-5-hydroxy-,
trisodium salt
2 yrs
No 1500 kg UV
610 Ciba 3074 Chemical in
Absorber
Specialty Cibafast HLF
for Textiles
Chemicals
Pty Ltd
Yes 880 kg Textile Dye 1 yr
611 Ciba 3074 benzenesulfonic
Specialty acid, 2,4-
Chemicals diamino-3-[[4-
Pty Ltd [[2-
(sulfooxy)ethyl]
sulfonyl]-
phenyl]azo]-5-
[[2-sulfo-4-[[2-
(sulfooxy)ethyl]
sulfonyl]phenyl]
azo]-, potassium
sodium salt
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
60
Yes 800 kg Textile Dye 1 yr
612 Ciba 3074 2-
Specialty Naphthalenesulf
Chemicals onic acid, 7-
Pty Ltd amino-4-
hydroxy,
coupled with
diazotized 2-[(4-
aminophenyl)
sulfonyl] ethyl
hydrogen sulfate
and diazotized
2-amino-5-[[2-
(sulfooxy) ethyl]
sulfonyl]
benzenesulfonic
acid, potassium
sodium salts
Yes 3000 kg Textile Dye 2 yrs
613 Ciba 3074 3-Bromo-2-[4-
Specialty N,N-bis(2-
Chemicals cyanoethyl)amin
Pty Ltd ophenylazo]-5-
nitro-
benzotrifluoride
Yes 2000 kg Oil Pipeline 18 mths
614 Baker 3195 Amine
Additive
Petrolite, A compound in
Division of RE5911HIWLD
Baker Hughes HI
Aust Pty Ltd
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
61
26 EARLY INTRODUCTION PERMITS FOR NON-HAZARDOUS INDUSTRIAL
CHEMICALS
The permits listed in Table 3 were issued to import or manufacture the following chemicals
prior to the issue of their respective assessment certificates under section 30A of the Act.
Table 2
Early Introduction Permits
PERMIT COMPANY CHEMICAL OR USE
NUMBER NAME TRADE NAME
380 International Polymer in Tego Airex Component in paint
Sales & 900
Marketing Pty
Ltd
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
62
27 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE AUSTRALIAN
INVENTORY OF CHEMICAL SUBSTANCES FIVE YEARS AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 14(1) of the Industrial Chemicals (Notification
and Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 3
Chemicals Eligible for Listing on the Australian Inventory of Chemical Substances
CHEMICAL NAME CAS MOLECULA
NUMBER R FORMULA
239441-91-9 ((C15H16O2.C3H
2-Propenoic acid, 2-methyl-, polymer with
(chloromethyl)oxirane polymer with 4,4'-(1- 5ClO)x.C8H8.xC
methylethylidene)bis[phenol] 3- 4H6O3.C4H6O2)x
oxobutanoate, and ethenylbenzene
Butanoic acid, 3-oxo-, 2-[(2-methyl-1-oxo-2- 239107-45-0 (C10H14O5.C7H1
propenyl) oxy]ethyl ester, polymer with butyl 2O2.C5H8O2.C5
2-propenoate, ethyl 2-propenoate and methyl H8O2)x
2-methyl-2-propenoate
845730-14-5 C31H27N5O13S2
1H-Pyrazole-3-carboxylic acid, 4-[5-[3-
.4 K
carboxy-5-hydroxy-1-(4-sulfophenyl)-1H-
pyrazol-4-yl]-3-(1-piperidinylcarbonyl)-2,4-
pentadienylidene]-4,5-
dihydro-5-oxo-1-(4-sulfophenyl)-,
tetrapotassium salt
68920-56-9 Unspecified
Clarified oils, petroleum, catalytic cracked,
reaction products with cresol and
polymethylenepolyphenylene isocyanate
184785-42-0 (C21H28O4.C19H
1,4-Benzenedicarboxylic acid, polymer with
24O4.C9H4O5.C8
1,3-dihydro-1,3-dioxo-5-
H6O4.C2H6O2)x
isobenzofurancarboxylic acid, 1,2-ethanediol,
2,2'-[(1-methylethylidene)bis(4,1-
phenyleneoxy)]bis[ethanol] and 1,1'-[(1-
methylethylidene)bis(4,1-
phenyleneoxy)]bis[2-propanol]
149530-92-7 (C18H34O3.C6H1
9-Octadecenoic acid, 12-hydroxy-, (9Z,12R)-
0O2.C2H5N)x
, polymer with aziridine and 2-oxepanone
23911-56-0 C11H10O2
Ethanone, 1-(3-methyl-2-benzofuranyl)-
852998-92-6 (C14H26O2.C10H
Neodecanoic acid, polymer with butyl 2-
20O2.C8H8.C7H1
propenoate, ethenylbenzene, 2-hydroxyethyl
2O2.C6H10O3.C5
2-methyl-2-propenoate, isodecyl 2-methyl-2-
H8O2.C3H6O2.C
propenoate, methyl 2-methyl-2-propenoate,
3H4O2)x
oxiranemethanol and 2-propenoic acid
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
63
Octadecanoic acid, monoester with 1,2,3- 852999-22-5 C21H42O4.C9H6
propanetriol, polymer with 1,3- N2O2.C5H13NO2
diisocyanatomethylbenzene, 3-hydroxy-2- .C5H10O4.C3H8
(hydroxymethyl)-2-methylpropanoic acid, O3)x.Na
2,2'-(methylimino)bis[ethanol] and 1,2,3-
propanetriol, sodium salt
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
64
28 NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 13B of the Industrial Chemicals (Notification and
Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 5
Chemicals Eligible for Immediate Listing on the Australian Inventory of Chemical
Substances
CHEMICAL NAME CAS MOLECULA
NUMBER R FORMULA
145417-44-3 (C14H20O4.C8H8
7-Oxabicyclo[4.1.0]heptane-3-carboxylic
acid, 7-oxabicyclo[4.1.0]hept-3-ylmethyl .C3H3N)x
ester, polymer with ethenylbenzene and 2-
propenenitrile
Chemical Gazette Commonwealth of Australia Gazette
No. C 8,2 August 2005
|