Material Safety Data Sheet
Emergency Phone:(248)-373-8100 24-Hour CHEMTREC (800)-424-9300 CHEMTREC, D.C. Area (800)-483-7616
I. Chemical Product And Company Data
2
Health
PRODUCT: ISO-FLEX Epoxy 200 PART A
CHEMICALFAMILY: Epoxy resin 1
Flammability
REVISION DATE: MAR 2007 0
Reactivity
MANUFACTURER: LymTal International, Inc. H
Personal Protection
4150 S. Lapeer Rd. Orion, MI 48359
II. Composition / Information On Ingredients
This document is prepared pursuant to the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Where a proprietary ingredient is shown, the identity may be made available as provided in this standard.
All components of this product are included in the EPA Toxic Substances Control Act (TSCA) Chemical
Substance Inventory.
EXPOSURE LIMITS
HAZARDOUS INGREDIENTS CAS NO TLV STEL PEL CONTENT
N/E N/E N/E
Bis A Epoxy Resin 25068-38-6 0 ?80%
N/E N/E N/E
Bis F Epoxy Resin 28064-14-4 0 ?40%
N/E N/E N/E
Glycidyl Diluent 2461-15-6 0 ?20%
N/E = Not Established
California Proposition 65 ingredients
None
Section 313 Supplier Notification
This product contains the following toxic chemicals subject to the reporting requirements of section 313 of
the Emergency Planning and Community Right to Know Act of 1986 (40CFR372)
None
III. Hazards Identification
HMIS Hazard Rating No. 2
PRIMARY ROUTE OF ENTRY: Eye and skin contact, breathing and ingestion.
Symptoms of Exposure
Skin Contact: Product may cause irritation, redness and discomfort which is transient.
Eyes: Product may cause severe irritation to the eyes.
Inhalation Vapors from product may cause irritation to the nose, throat and respiratory tract.
Coughing and chest pains may result. High vapor concentrations may produce CNS
depression.
Ingestion: Not expected to be a relevant route of exposure. Product may be slightly toxic if ingested.
LymTal International, Inc. ISOFLEX EPOXY 200 PART A Page 1 of 4
IV. First Aid Measures
Inhalation Remove victim from exposure. If difficulty with breathing, administer oxygen and
seek medical assistance
Eyes Flush eyes with cold water for a minimum of 15 minutes, lifting lower and upper eye
lids throughout. Seek immediate medical attention.
Skin Immediately remove contaminated clothing. Wash thoroughly with soap and water. If
irritation persists seek medical attention. Wash contaminated clothing before reuse.
Ingestion Do not induce vomiting, get immediate medical attention, if vomiting occurs
spontaneously keep head below hips to prevent aspiration of liquids into lungs. Do
not give anything by mouth to an unconscious person
V. Fire Fighting Methods
HMIS Hazard Rating No. 1
Flash Point: > 93oC (200oF) Method: Pensky Martin C.C.
General Hazard: None
Auto-Ignition Temp.: Not Available
Limits of Flammability LEL: Not Available UEL: Not Available
Extinguishing Media For small fires, use water spray, foam, CO2, or dry chemical. For large
fires, use water spray, fog, or alcohol foam.
Special Fire & Unusual Hazards Move containers from area if it can be done without risk. Cool fire-
exposed containers with water from the side. As in any fire, wear
NIOSH/MSHA approved, pressure demand self contained breathing
apparatus and full protective gear.
VI. Accidental Release Measures
Action To Take For Spills/ Leaks: Avoid contact with skin or eyes. Ventilate area, eliminate all sources of
ignition. Wear appropriate protective gear, contain leak or spill, salvage, clean up residue with absorbent
material.
Waste Disposal Method: Handle disposal of waste material in manner which complies with local, state,
province and federal regulation. Landfill if solidified, or incineration at agency approved waste-disposal
facilities.
VII. Handling And Storage
Average Shelf Life: Refer to Product Data Sheet
Special Instructions Store away from oxidizing agents and high
temperatures
VIII. Exposure Controls / Personal Protection
Ventilation: Ventilation is recommended. Air movement must be designed to insure turnover at all
locations in work area to avoid build up of heavy vapors.
Personal Protection Equipment: Do NOT wear contact lenses when working with this material. Use
chemical goggles/safety glasses with side shields and impervious gloves. Wear clothing with long sleeves
and pants. In operations where mists can be generated or the exposure limits for crystalline silica
exceeded, wear a NIOSH/MSHA approved dust/fume respirator selected by a technically qualified person
for the specific work conditions. Wear respirator protection whenever airborne concentrations exceed TLV
ceilings or TWA, use NIOSH approved respirators for listed hazard.
Confined spaces, room, or tanks are areas where concern for TLV's is especially important. Reference
OSHA regulation CFR 29 1910.134 for recommended respiratory protection.
LymTal International, Inc. ISOFLEX EPOXY 200 PART A Page 2 of 4
IX. Physical And Chemical Properties
Boiling Point (oC): N/D Water/Oil Distribution N/A
Coefficient:
Percent Volatile: 0.1% ( 1.14 g/l) Solubility in Water: Negligible
Freezing Point (oC): N/A Specific Gravity @20?C 1.13
Vapor Pressure @ 20o C <10 pH: N/A
Vapor Density >air Evaporation Rate: N/A
Odor Threshold: N/A Odor: slight
Appearance: Amber liquid
N/A = Not Available N/D=NOT Determined Ca. = Approximate
X. Stability And Reactivity
HMIS Hazard Rating No. 0
Stability Stable
Incompatibility: Strong acids, oxidizing agents, bases, amines and mercaptans.
Hazardous Decomposition Products Oxides of Carbon; aldehydes and acids. Decomposition and
combustion products may be toxic.
Conditions To Avoid Strong acids in bulk.
XI. Toxicity Information
HMIS Hazard Rating No. 2
PRIMARY ROUTE OF ENTRY: Inhalation, dermal, and eyes.
Effects Of Overexposure
Inhalation: May cause irritation to the respiratory tract.
Eyes: May be severely irritating to the eyes.
Skin Contact: Irritating to the skin. In some individuals it may cause sensitization.
Ingestion: May cause permanent damage to the mouth throat and stomach.
Chronic: This product does not contain chemicals considered to be carcinogenic by
NTP, IRAC, ACGIH, OSHA.
However this product does contain (<5ppm) of epichlorohydrin ECH cas no
106-89-8. It is unlikely that normal work practices with this product could result
in measurable concentrations in the workplace. Please be aware that ECH
has been reported to produce cancer in lab animals and top cause mutagenic
changes in bacteria and cultured human cells. It has been classified as a
suspected human carcinigen by the NTP.
XII. Ecological Information
Marine Pollutant: NL
(NL = Not Listed; P = Moderate; PP = Severe; ND = Not Determined)
XIII. Disposal Considerations
Handle disposal of waste material in manner which complies with all applicable local, state, provincial and
federal regulations.
LymTal International, Inc. ISOFLEX EPOXY 200 PART A Page 3 of 4
XIV. Transport Information
DOT SHIPPING INFORMATON
Not Regulated
XV. Regulatory Information
OSHA Hazard Communication Standard Hazardous
(29 CFR 1910.1200)
CERCLA/ Super fund (40 CFR 117,302) N/A
SARA Extremely Hazardous Substances N/A
(40 CFR 355)
SARA Hazard Categories (40 CFR 370) Health : Immediate
Physical: Fire
SARA Toxic Chemicals (40 CFR 372) None
Inventory Status The chemicals in this product are listed on the US
TSCA Chemical Substance Inventory and the
Canadian Domestic Substances List.
XVI. Other Information
THE INFORMATION HEREIN HAS BEEN COMPLIED FROM SOURCES BELIEVED TO BE RELIABLE
AND IS ACCURATE TO THE BEST OF OUR KNOWLEDGE. HOWEVER, LymTal INTERNATIONAL INC.
CAN NOT GIVE ANY GUARANTEES REGARDING INFORMATION FROM OTHER SOURCES, AND
EXPRESSLY DOES NOT MAKE ANY WARRANTIES, NOR ASSUMES ANY LIABILITY, FOR ITS USE.
LymTal International, Inc. ISOFLEX EPOXY 200 PART A Page 4 of 4
Material Safety Data Sheet
Emergency Phone:(248)-373-8100 24-Hour CHEMTREC (800)-424-9300 CHEMTREC, D.C. Area (800)-483-7616
I. Chemical Product And Company Data
3
Health
PRODUCT: ISO-FLEX Epoxy 200 PART B
CHEMICALFAMILY: Amine Mixture 1
Flammability
REVISION DATE: MAR 2007 0
Reactivity
MANUFACTURER: LymTal International, Inc. H
Personal Protection
4150 S. Lapeer Rd. Orion, MI 48359
II. Composition / Information On Ingredients
This document is prepared pursuant to the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Where a proprietary ingredient is shown, the identity may be made available as provided in this standard.
All components of this product are included in the EPA Toxic Substances Control Act (TSCA) Chemical
Substance Inventory.
EXPOSURE LIMITS
HAZARDOUS INGREDIENTS CAS NO TLV STEL PEL CONTENT
N/E N/E N/E
Polyamine 68953-36-6 <30%
N/E N/E N/E
Trade Secret X >20%
4.2 mg/m3 10-30 ppm
N/E
Aliphatic Amine 111-40-0 <10%
N/E N/E N/E
Amino Phenol 90-72-2 <5%
N/E N/E N/E
Bisphenol A 80-05-7 <5%
N/E = Not Established
California Proposition 65 ingredients
None
Section 313 Supplier Notification
This product contains the following toxic chemicals subject to the reporting requirements of section 313 of
the Emergency Planning and Community Right to Know Act of 1986 (40CFR372)
None
III. Hazards Identification
HMIS Hazard Rating No. 3
PRIMARY ROUTE OF ENTRY: Eye and skin contact, breathing and ingestion.
Symptoms of Exposure
Skin Contact: Corrosive to the skin. May cause skin sensitization.
Eyes: Product may cause severe irritation to the eyes. Corrosive to the eyes and may cause
severe damage including blindness.
Inhalation Vapors or mist may be corrosive to the upper respiratory tract. Long term exposure may
result in lung damage which will be apparent by shortness of breath and a chronic cough.
Ingestion: Not expected to be a relevant route of exposure. It may however cause permanent
damage to the throat mouth and stomach.
LymTal International, Inc. ISOFLEX EPOXY 200 PART B Page 1 of 4
IV. First Aid Measures
Inhalation Remove victim from exposure. If difficulty with breathing, administer oxygen and
seek medical assistance
Eyes Flush eyes with cold water for a minimum of 15 minutes, lifting lower and upper eye
lids throughout. Seek immediate medical attention.
Skin Immediately remove contaminated clothing. Wash thoroughly with soap and water. If
irritation persists seek medical attention. Wash contaminated clothing before reuse.
Ingestion Do not induce vomiting, get immediate medical attention, if vomiting occurs
spontaneously keep head below hips to prevent aspiration of liquids into lungs. Do
not give anything by mouth to an unconscious person
V. Fire Fighting Methods
HMIS Hazard Rating No. 1
Flash Point: > 93oC (200oF) Method: Pensky Martin C.C.
General Hazard: None
Auto-Ignition Temp.: Not Available
Limits of Flammability LEL: Not Available UEL: Not Available
Extinguishing Media For small fires, use water spray, foam, CO2, or dry chemical. For large
fires, use water spray, fog, or alcohol foam.
Special Fire & Unusual Hazards Move containers from area if it can be done without risk. Cool fire-
exposed containers with water from the side. As in any fire, wear
NIOSH/MSHA approved, pressure demand self contained breathing
apparatus and full protective gear.
VI. Accidental Release Measures
Action To Take For Spills/ Leaks: Avoid contact with skin or eyes. Ventilate area, eliminate all sources of
ignition. Wear appropriate protective gear, contain leak or spill, salvage, clean up residue with absorbent
material.
Waste Disposal Method: Handle disposal of waste material in manner which complies with local, state,
province and federal regulation. Landfill if solidified, or incineration at agency approved waste-disposal
facilities.
VII. Handling And Storage
Average Shelf Life: Refer to Product Data Sheet
Special Instructions Store away from open flames and high
temperatures
VIII. Exposure Controls / Personal Protection
Ventilation: Ventilation is recommended. Air movement must be designed to insure turnover at all
locations in work area to avoid build up of heavy vapors.
Personal Protection Equipment: Do NOT wear contact lenses when working with this material. Use
chemical goggles/safety glasses with side shields and impervious gloves. Wear clothing with long sleeves
and pants. In operations where mists can be generated or the exposure limits for crystalline silica
exceeded, wear a NIOSH/MSHA approved dust/fume respirator selected by a technically qualified person
for the specific work conditions. Wear respirator protection whenever airborne concentrations exceed TLV
ceilings or TWA, use NIOSH approved respirators for listed hazard.
Confined spaces, room, or tanks are areas where concern for TLV's is especially important. Reference
OSHA regulation CFR 29 1910.134 for recommended respiratory protection.
LymTal International, Inc. ISOFLEX EPOXY 200 PART B Page 2 of 4
IX. Physical And Chemical Properties
Boiling Point (oC): N/D Water/Oil Distribution N/A
Coefficient:
Percent Volatile: 0.1% ( 1.01 g/l ) Solubility in Water: Negligible
Freezing Point (oC): N/A Specific Gravity @20?C 1.20
Vapor Pressure @ 20o C <10 pH: N/A
Vapor Density >air Evaporation Rate: N/A
Odor Threshold: N/A Odor: Ammonical
Appearance: Amber liquid
N/A = Not Available N/D=NOT Determined Ca. = Approximate
X. Stability And Reactivity
HMIS Hazard Rating No. 0
Stability Stable
Incompatibility: Strong acids, oxidizing agents, bases, amines and mercaptans.
Hazardous Decomposition Products Carbon dioxide and oxides of nitrogen. Decomposition and
combustion products may be toxic.
Conditions To Avoid Avoid heat, flame and contact with strong oxidizing agents.
XI. Toxicity Information
HMIS Hazard Rating No. 3
PRIMARY ROUTE OF ENTRY: Inhalation, dermal, and eyes.
Effects Of Overexposure
Inhalation: Vapors may be corrosive to the upper respiratory tract.
Eyes: May cause severe damage including blindness.
Skin Contact: Irritating to the skin. In some individuals it may cause sensitization.
Ingestion: May cause permanent damage to the mouth throat and stomach.
Chronic: This product does not contain chemicals considered to be carcinogenic by
NTP, IRAC, ACGIH, OSHA.
XII. Ecological Information
Marine Pollutant: NL
(NL = Not Listed; P = Moderate; PP = Severe; ND = Not Determined)
XIII. Disposal Considerations
Handle disposal of waste material in manner which complies with all applicable local, state, provincial and
federal regulations.
XIV. Transport Information
DOT SHIPPING INFORMATON
Corrosive liquid, N.O.S (alkaline amine )
DOT Proper Shipping Name
Class 8 ( corrosive liquid ), PG III
DOT Hazard Class
UN1760 Class 60 DOT PLACARD Corrosive
DOT I.D. Number
LymTal International, Inc. ISOFLEX EPOXY 200 PART B Page 3 of 4
XV. Regulatory Information
OSHA Hazard Communication Standard Hazardous
(29 CFR 1910.1200)
CERCLA/ Super fund (40 CFR 117,302) N/A
SARA Extremely Hazardous Substances N/A
(40 CFR 355)
SARA Hazard Categories (40 CFR 370) Health : Immediate
Physical: Fire
SARA Toxic Chemicals (40 CFR 372) None
Inventory Status The chemicals in this product are listed on the US
TSCA Chemical Substance Inventory and the
Canadian Domestic Substances List.
XVI. Other Information
THE INFORMATION HEREIN HAS BEEN COMPLIED FROM SOURCES BELIEVED TO BE RELIABLE
AND IS ACCURATE TO THE BEST OF OUR KNOWLEDGE. HOWEVER, LymTal INTERNATIONAL INC.
CAN NOT GIVE ANY GUARANTEES REGARDING INFORMATION FROM OTHER SOURCES, AND
EXPRESSLY DOES NOT MAKE ANY WARRANTIES, NOR ASSUMES ANY LIABILITY, FOR ITS USE.
LymTal International, Inc. ISOFLEX EPOXY 200 PART B Page 4 of 4
|