Material Safety Data Sheet
Freeman 90-1 Aluminum Mold-Seal Coating
Date of Preparation: January 3, 2007 Revision:
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: Freeman 90-1 Aluminum Mold-Seal Coating HMIS
Chemical Family: N/A 2
H
CAS Number: N/A 3
F
Other Designations: N/A 0
R
General Use: N/A PPE鈥?
Manufacturer: Freeman Manufacturing and Supply Company, 1101 Moore Road, Avon, OH 44011, 鈥燬ec. 8
Phone (440)934-1902, FAX (440)934-7200, Hours of Operation 8-5, Emergency Phone Number 800-424-9300.
Emergency Overview
Flammable, Irritant, Inhalation
Section 2 - Composition / Information on Ingredients
% wt or
Ingredient Name CAS Number
% vol
Amyl Acetate 628-63-7 10-20
Anhyd. Isopropyl Alcohol 67-63-0 10-20
VM&P Naphtha 64742-89-8 10-20
Toluene* 108-88-3 <10
Methyl Ethyl Ketone * 78-93-3 < 10
Isobutyl Alcohol 78-83-1 <10
Mineral Spirits 66 8052-41-3 <5
Ethylene Glycol Monobutyl Ether 111-76-2 <5
Methyl Isobutyl Ketone * 108-10-1 <5
Xylene 1330-20-7 <1
Ethyl Benzene 100-41-4 <1
* Indicates toxic chemicals subject to the reporting requirements of Section 313 of Title III and of 40 CFR 372. 65
OSHA ACGIH Vapor Pressure
@ Temp掳F
Ingredient PEL STEL TLV STEL MmHg
100 ppm none estab. 100 ppm none estab. 4 68
Amyl Acetate
400 ppm none estab. 400 ppm none estab. 33 68
Anhyd. Isopropyl
Alcohol
300 ppm none estab. 300 ppm none estab. 10.2 68
VM&P Naphtha
100 ppm none estab. 50 ppm none estab. 26 68
Toluene
200 ppm none estab. 200 ppm none estab. 78 68
Methyl Ethyl
Ketone
100 ppm none estab. 50 ppm none estab. 8.8 68
Isobutyl Alcohol
100 ppm none estab. 100 ppm none estab. 2 68
Mineral Spirits 66
25 ppm none estab. 25 ppm none estab. 0.66 68
Ethylene Glycol
Monobutyl Ether
100 ppm none estab. 50 ppm none estab. 16 68
Methyl Isobutyl
Ketone
100 ppm none estab. 50 ppm none estab. 14.2 100
Xylene
100 ppm none estab. 100 ppm none estab. 7.1 68
Ethyl Benzene
Freeman 90-1 Aluminum Mold-Seal Coating Revision:
Section 3 - Physical and Chemical Properties
Appearance and Odor: Aluminum liquid, Strong solvent Water Solubility: Negligible
odor Boiling Range: 175 掳F- 336 掳F
Coating VOC: 5.13 lb/gal Evaporation Rate: Slower than ether
Material VOC: 5.13 lb/gal Vapor Density (Air=1): Heavier than air.
Specific Gravity (H2O=1, at 4 掳C): 0.94
Section 4 - Fire-Fighting Measures
NFPA
Flash Point: 23 掳F (-5潞C)
Flash Point Method: TCC
3
LEL: 0.9% by volume
0
2
UEL: 20% by volume
鈥?
Extinguishing Media: Foam, CO2, dry chemical
Unusual Fire and Explosion Hazards: Keep containers tightly closed. Isolate from heat, electrical
equipment, sparks and open flame. Closed containers may explode when exposed to extreme heat. Do not apply to hot
surfaces.
Fire-Fighting Instructions: Water spray may be ineffective. Use fog nozzles. Cool fire exposed containers with water.
Section 5 - Stability and Reactivity
Stability: Stable under recommended handling and storage conditions.
Conditions to Avoid: High temperatures, flames
Incompatibility (Materials to Avoid): N/A
Hazardous Decomposition Products: May produce hazardous fumes when heated. Carbon monoxide, oxides of nitrogen.
Hazardous Polymerization: Will not occur.
Section 6 - Health Hazard Information
Potential Health Effects
Inhalation: Anesthetic. Irritation of the respiratory tract or acute nervous system depression characterized by headache,
dizziness, staggering gait, confusion, unconsciousness, or coma.
Skin and Eye Contact: Primary irritation.
Skin: Prolonged or repeated exposure to this material may cause redness and burning, during, and cracking of the skin and
dermatitis. Person with pre-existing skin disorders may be more susceptible.
Ingestion: Do not induce vomiting. Consult a physician or poison control center.
Health Hazards (Acute and Chronic): Pre-existing heart disorders may be aggravated by exposure to this material.
Caution: Toluene - may be harmful to the fetus based on laboratory animal studies.
Carcinogenicity: Contains very low levels of Benzene as an impurity either of Toluene or Xylene. Our MSDS on the products
indicate the specific solvents present. Benzene, toluene, xylene and ethyl benzene are classified by the State of California as
cancer hazards.
Medical Conditions Aggravated by Long-Term Exposure: Any medical condition, allergy, or sensitization can become worse
upon exposure.
Emergency and First Aid Procedures
Inhalation: Remove from exposure. Restore breathing. Keep warm and quiet. Notify a physician.
Eyes: Flush immediately with large amounts of water for 15 minutes. See a physician.
Skin: Wash affected areas thoroughly with soap and water. Remove contaminated clothing.
Ingestion: Do not induce vomiting. Consult a physician or poison control center.
Section 7 - Spill, Leak, and Disposal Procedures
Spill /Leak Procedures: Remove all sources of ignition. Ventilate area. Remove with inert absorbent and non-sparking tools.
Disposal: Disposal in accordance with local, state, and federal regulation. Incinerate in approved facility. Do not incinerate
closed containers. Emptied containers may retain hazardous residue and explosive vapors. Contact your supplier or a licensed
contractor for detailed recommendations. Follow applicable Federal, state, and local regulations.
Page 2 of 3
Revision: Freeman 90-1 Aluminum Mold-Seal Coating
State Regulations:
California Proposition 65: Contains - Benzene, toluene, xylene and ethyl benzene
Materials on the New Jersey Right to Know List: Amyl acetate, methyl isobutyl ketone, isopropyl alcohol, methyl ethyl
ketone, toluene; isobutyl alcohol, xylene, and ethyl benzene
Materials on the Pennsylvania Right to Know List: Amyl acetate, methyl isobutyl ketone, isopropyl alcohol, methyl ethyl
ketone, toluene; isobutyl alcohol, xylene and ethyl benzene
Materials on the Massachusetts Right to Know List: Amyl acetate, methyl isobutyl ketone, isopropyl alcohol, methyl ethyl
ketone, toluene; isobutyl alcohol, xylene and ethyl benzene
Regulatory Information:
TSCA Inventory Status: All ingredients listed on TSCA Inventory.
Section 8 - Exposure Controls / Personal Protection
Ventilation: In restricted ventilation areas use Bureau of Mines approved chemical mechanical filters designed to remove a
combination of particulate and gas/vapor. In confined areas use Bureau of Mines approved air line type respirator.
Respiratory Protection: In outdoor or open areas use Bureau of Mines approved mechanical filter respirator to remove solid air
borne particles of overspray during spray application.
Protective Gloves: Wear resistant gloves such as: Natural rubber, or neoprene.
Eye Protection: Chemical splash goggles in compliance with OSHA regulation.
Other Protective Clothing or Equipment: To prevent repeated or prolonged skin contact, wear impervious clothing and boots.
Work/Hygienic Practices: Wash hands before eating or using the washrooms, smoke in smoking areas only.
Section 9 - Special Precautions and Comments
Handling and Storage:
Handling Precautions: Ground containers when pouring. Avoid free fall of liquid in excess of a few inches. Do not flame cut,
braze or weld.
Storage Requirements: Do not store above 120掳F. Store large quantities in building designed and protected for storage of
NFPA Class Liquids.
DOT Transportation Data (49 CFR 172.101):
Shipping Name: Paint Packaging Authorizations Quantity Limitations
Flammable Liquid 3 a) Exceptions: a) Passenger, Aircraft, or Railcar:
Shipping Symbols: b) Non-bulk Packaging: b) Cargo Aircraft Only:
Hazard Class: 3 c) Bulk Packaging:
ID No.: UN 1263 Vessel Stowage Requirements
Packing Group: II a) Vessel Stowage:
Label: Flammable Liquid b) Other:
Special Provisions (172.102):
Prepared By:
Revision Notes:
Disclaimer: The following supersedes Buyer鈥檚 documents. SELLER MAKES NO REPRESENTATION OR WARRANTY,
EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. No statements herein are to be construed as inducements to infringe any relevant patent. Under no circumstances shall
Seller be liable for incidental, consequential or indirect damages for alleged negligence, breach of warranty, strict of liability arising
in connection with the product(s). Buyer鈥檚 sole remedy and Seller鈥檚 sole liability for any claims shall be Buyer鈥檚 purchase price.
Data and results are based on controlled lab work and must be confirmed by Buyer by testing for its intended conditions of use. The
product(s) has not been tested for, and is therefore not recommended for, uses for which prolonged contact with mucous membranes,
abraded skin, or blood is intended; or for uses for which implantation within the human body is intended.
Page 3 of 3
|