NFPA 704 (Section 16)
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
1. CHEMICAL PRODUCT and COMPANY INFORMATION (rev. Jan-98)
Amerada Hess Corporation
1 Hess Plaza
Woodbridge, NJ 07095-0961
EMERGENCY TELEPHONE NUMBER (24 hrs): CHEMTREC (800) 424-9300
COMPANY CONTACT (business hours): Corporate Safety (732) 750-6000
SYNONYMS: #2 Heating Oil; 2 Oil; Off-road Diesel Fuel
See Section 16 for abbreviations and acronyms.
2. COMPOSITION and INFORMATION ON INGREDIENTS (rev. Sep-98)
CONCENTRATION
INGREDIENT NAME EXPOSURE LIMITS PERCENT BY WEIGHT
5 mg/m3 as mineral oil mist
OSHA PEL-TWA: 100
#2 Fuel Oil
ACGIH TLV-TWA: 1997 NOIC - 100 mg/m3, skin, A3
CAS NUMBER: 68476-30-2
OSHA PEL-TWA: 10 ppm Typically 0.1
Naphthalene
ACGIH TLV-TWA/STEL: 10 / 15 ppm, A4
CAS NUMBER: 91-20-3
A complex combination of hydrocarbons with carbon numbers in the range C9 and higher produced from
the distillation of petroleum crude oil.
3. HAZARDS IDENTIFICATION (rev. Jan-98; Tox-98)
EMERGENCY OVERVIEW
CAUTION!
OSHA/NFPA COMBUSTIBLE LIQUID - SLIGHT TO MODERATE IRRITANT - EFFECTS CENTRAL
NERVOUS SYSTEM - HARMFUL OR FATAL IF SWALLOWED
Moderate fire hazard. Avoid breathing vapors or mists. May cause dizziness and drowsiness. May cause
moderate eye irritation and skin irritation. Long-term, repeated exposure may cause skin cancer.
If ingested, do NOT induce vomiting, as this may cause chemical pneumonia (fluid in the lungs).
EYES
Contact with eyes may cause mild irritation.
SKIN
Practically non-toxic if absorbed following acute (single) exposure. May cause skin irritation with
prolonged or repeated contact. Liquid may be absorbed through the skin in toxic amounts if large areas of
skin are repeatedly exposed.
INGESTION
The major health threat of ingestion occurs from the danger of aspiration (breathing) of liquid drops into
the lungs, particularly from vomiting. Aspiration may result in chemical pneumonia (fluid in the lungs),
severe lung damage, respiratory failure and even death.
Ingestion may cause gastrointestinal disturbances, including irritation, nausea, vomiting and diarrhea, and
central nervous system (brain) effects similar to alcohol intoxication. In severe cases, tremors,
convulsions, loss of consciousness, coma, respiratory arrest, and death may occur.
INHALATION
Excessive exposure may cause irritations to the nose, throat, lungs and respiratory tract. Central nervous
system (brain) effects may include headache, dizziness, loss of balance and coordination,
unconsciousness, coma, respiratory failure, and death.
Revision Date: 02/28/01 Page 1 of 7
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
WARNING: the burning of any hydrocarbon as a fuel in an area without adequate ventilation may result in
hazardous levels of combustion products, including carbon monoxide, and inadequate oxygen levels,
which may cause unconsciousness, suffocation, and death.
CHRONIC EFFECTS and CARCINOGENICITY
Similar products have produced skin cancer and systemic toxicity in laboratory animals following repeated
applications. The significance of these results to human exposures has not been determined - see
Section 11Toxicological Information.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
Irritation from skin exposure may aggravate existing open wounds, skin disorders, and dermatitis (rash).
4. FIRST AID MEASURES (rev. Jan-98; Tox-98)
EYES
In case of contact with eyes, immediately flush with clean, low-pressure water for at least 15 min. Hold
eyelids open to ensure adequate flushing. Seek medical attention.
SKIN
Remove contaminated clothing. Wash contaminated areas thoroughly with soap and water or with
waterless hand cleanser. Obtain medical attention if irritation or redness develops.
INGESTION
DO NOT INDUCE VOMITING. Do not give liquids. Obtain immediate medical attention. If spontaneous
vomiting occurs, lean victim forward to reduce the risk of aspiration. Monitor for breathing difficulties.
Small amounts of material which enter the mouth should be rinsed out until the taste is dissipated.
INHALATION
Remove person to fresh air. If person is not breathing, provide artificial respiration. If necessary, provide
additional oxygen once breathing is restored if trained to do so. Seek medical attention immediately.
5. FIRE FIGHTING MEASURES (rev. Sep-94)
FLAMMABLE PROPERTIES:
o o
FLASH POINT: 100 F (38 C) minimum PMCC
o o
AUTOIGNITION POINT: 494 F (257 C)
LOWER EXPLOSIVE LIMIT (%): 0.6
UPPER EXPLOSIVE LIMIT (%): 7.5
FIRE AND EXPLOSION HAZARDS
OSHA and NFPA Class 2 COMBUSTIBLE LIQUID (see Section 14 for transportation classification).
Vapors may be ignited rapidly when exposed to heat, spark, open flame or other source of ignition. When
mixed with air and exposed to an ignition source, flammable vapors can burn in the open or explode in
confined spaces. Being heavier than air, vapors may travel long distances to an ignition source and flash
back. Runoff to sewer may cause fire or explosion hazard.
EXTINGUISHING MEDIA
SMALL FIRES: Any extinguisher suitable for Class B fires, dry chemical, CO2, water spray, fire fighting
foam, or Halon.
LARGE FIRES: Water spray, fog or fire fighting foam. Water may be ineffective for fighting the fire, but
may be used to cool fire-exposed containers.
FIRE FIGHTING INSTRUCTIONS
Small fires in the incipient (beginning) stage may typically be extinguished using handheld portable fire
extinguishers and other fire fighting equipment.
Revision Date: 02/28/01 Page 2 of 7
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
Firefighting activities that may result in potential exposure to high heat, smoke or toxic by-products of
combustion should require NIOSH/MSHA- approved pressure-demand self-contained breathing apparatus
with full facepiece and full protective clothing.
Isolate area around container involved in fire. Cool tanks, shells, and containers exposed to fire and
excessive heat with water. For massive fires the use of unmanned hose holders or monitor nozzles may
be advantageous to further minimize personnel exposure. Major fires may require withdrawal, allowing
the tank to burn. Large storage tank fires typically require specially trained personnel and equipment to
extinguish the fire, often including the need for properly applied fire fighting foam.
See Section 16 for the NFPA 704 Hazard Rating.
6. ACCIDENTAL RELEASE MEASURES (rev. Jan-98)
ACTIVATE FACILITY'S SPILL CONTINGENCY OR EMERGENCY RESPONSE PLAN.
Evacuate nonessential personnel and remove or secure all ignition sources. Consider wind direction; stay
upwind and uphill, if possible. Evaluate the direction of product travel, diking, sewers, etc. to confirm spill
areas. Spills may infiltrate subsurface soil and groundwater; professional assistance may be necessary to
determine the extent of subsurface impact.
Carefully contain and stop the source of the spill, if safe to do so. Protect bodies of water by diking,
absorbents, or absorbent boom, if possible. Do not flush down sewer or drainage systems, unless system
is designed and permitted to handle such material. The use of fire fighting foam may be useful in certain
situations to reduce vapors. The proper use of water spray may effectively disperse product vapors or the
liquid itself, preventing contact with ignition sources or areas/equipment that require protection.
Take up with sand or other oil absorbing materials. Carefully shovel, scoop or sweep up into a waste
container for reclamation or disposal. Response and clean-up crews must be properly trained and must
utilize proper protective equipment (see Section 8).
7. HANDLING and STORAGE (rev. Jan-98)
HANDLING PRECAUTIONS
Handle as a combustible liquid. Keep away from heat, sparks, excessive temperatures and open flame!
No smoking or open flame in storage, use or handling areas. Bond and ground containers during product
transfer to reduce the possibility of static-initiated fire or explosion.
Special slow load procedures for "switch loading" must be followed to avoid the static ignition hazard that
can exist when this product is loaded into tanks previously containing low flash point products (such as
gasoline) - see API Publication 2003, "Protection Against Ignitions Arising Out Of Static, Lightning and
Stray Currents."
STORAGE PRECAUTIONS
Keep containers closed and clearly labeled. Use approved vented storage containers. Empty product
containers or vessels may contain explosive vapors. Do not pressurize, cut, heat, weld or expose such
containers to sources of ignition.
Store in a well-ventilated area. This storage area should comply with NFPA 30 "Flammable and
Combustible Liquid Code". Avoid storage near incompatible materials. The cleaning of tanks previously
containing this product should follow API Recommended Practice (RP) 2013 "Cleaning Mobile Tanks In
Flammable and Combustible Liquid Service" and API RP 2015 "Cleaning Petroleum Storage Tanks."
WORK/HYGIENIC PRACTICES
Emergency eye wash capability should be available in the near proximity to operations presenting a
potential splash exposure. Use good personal hygiene practices. Avoid repeated and/or prolonged skin
exposure. Wash hands before eating, drinking, smoking, or using toilet facilities. Do not use as a
cleaning solvent or harsh abrasive skin cleaners for washing this product from exposed skin areas.
Waterless hand cleaners are effective. Promptly remove contaminated clothing and launder before reuse.
Revision Date: 02/28/01 Page 3 of 7
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
Use care when laundering to prevent the formation of flammable vapors which could ignite via washer or
dryer. Consider the need to discard contaminated leather shoes and gloves.
8. EXPOSURE CONTROLS and PERSONAL PROTECTION (rev. Jan-98)
ENGINEERING CONTROLS
Use adequate ventilation to keep vapor concentrations of this product below occupational exposure and
flammability limits, particularly in confined spaces.
EYE/FACE PROTECTION
Safety glasses or goggles are recommended where there is a possibility of splashing or spraying.
SKIN PROTECTION
Gloves constructed of nitrile, neoprene, or PVC are recommended. Chemical protective clothing such as
of E.I. DuPont TyChem? Saranex?or equivalent recommended based on degree of exposure. Note: The
resistance of specific material may vary from product to product as well as with degree of exposure.
Consult manufacturer specifications for further information.
RESPIRATORY PROTECTION
A NIOSH/MSHA-approved air-purifying respirator with organic vapor cartridges or canister may be
permissible under certain circumstances where airborne concentrations are or may be expected to exceed
exposure limits or for odor or irritation. Protection provided by air-purifying respirators is limited. Refer to
OSHA 29 CFR 1910.134, ANSI Z88.2-1992, NIOSH Respirator Decision Logic, and the manufacturer for
additional guidance on respiratory protection selection.
Use a positive pressure, air-supplied respirator if there is a potential for uncontrolled release, exposure
levels are not known, in oxygen-deficient atmospheres, or any other circumstance where an air-purifying
respirator may not provide adequate protection.
9. PHYSICAL and CHEMICAL PROPERTIES (rev. Jul-98)
APPEARANCE
Red or reddish/orange colored (dyed) liquid
ODOR
Mild, petroleum distillate odor
BASIC PHYSICAL PROPERTIES
o o
BOILING RANGE: 340 to 700 F (171 to 371 C)
o o
VAPOR PRESSURE: 0.009 psia @ 70 F (21 C)
VAPOR DENSITY (air = 1): > 1.0
SPECIFIC GRAVITY (H2O = 1): AP 0.87
PERCENT VOLATILES: 100 %
EVAPORATION RATE: Slow; varies with conditions
SOLUBILITY (H2O): Negligible
10. STABILITY and REACTIVITY (rev. Sep-94)
STABILITY: Stable. Hazardous polymerization will not occur
CONDITIONS TO AVOID and INCOMPATIBLE MATERIALS
Avoid high temperatures, open flames, sparks, welding, smoking and other ignition sources. Keep away
from strong oxidizers; Viton ? Fluorel ?br>
HAZARDOUS DECOMPOSITION PRODUCTS
Carbon monoxide, carbon dioxide and non-combusted hydrocarbons (smoke).
Revision Date: 02/28/01 Page 4 of 7
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
11. TOXICOLOGICAL PROPERTIES (rev. Jan-98; Tox-98)
ACUTE TOXICITY
Acute Oral LD50 (rat): 14.5 ml/kg
Acute Dermal LD50 (rabbit): > 5 ml/kg
Guinea Pig Sensitization: negative
Primary dermal irritation: moderately irritating (Draize mean irritation score - 3.98 rabbits)
Draize eye irritation: mildly irritating (Draize score, 48 hours, unwashed - 2.0 rabbits)
CHRONIC EFFECTS AND CARCINOGENICITY
Carcinogenic: IARC: NO NTP: NO OSHA: NO ACGIH: 1997 NOIC: A3
Dermal carcinogenicity: positive - mice
Studies have shown that similar products produce skin tumors in laboratory animals following repeated
applications without washing or removal. The significance of this finding to human exposure has not been
determined. Other studies with active skin carcinogens have shown that washing the animal's skin with
soap and water between applications reduced tumor formation.
This product is similar to Diesel Fuel. IARC classifies whole diesel fuel exhaust particulates as probably
carcinogenic to humans (Group 2A) and NIOSH regards it as a potential cause of occupational lung
cancer based on animal studies and limited evidence in humans.
MUTAGENICITY (genetic effects)
Material of similar composition has been positive in a mutagenicity study.
12. ECOLOGICAL INFORMATION (rev. Jan-98)
Keep out of sewers, drainage areas and waterways. Report spills and releases, as applicable, under
Federal and State regulations.
13. DISPOSAL CONSIDERATIONS(rev. Jan-98)
Consult federal, state and local waste regulations to determine appropriate disposal options.
14. TRANSPORTATION INFORMATION (rev. Jan-98)
PROPER SHIPPING NAME: FUEL OIL, NO. 2
HAZARD CLASS & PACKING GROUP: 3, PG III
DOT IDENTIFICATION NUMBER: NA 1993
DOT SHIPPING LABEL: FLAMMABLE LIQUID
May be reclassified for transportation as a COMBUSTIBLE LIQUID under conditions of DOT 49 CFR
173.120(b)(2).
15. REGULATORY INFORMATION (rev. Feb-01)
U.S. FEDERAL, STATE, and LOCAL REGULATORY INFORMATION
This product and its constituents listed herein are on the EPA TSCA Inventory. Any spill or uncontrolled
release of this product, including any substantial threat of release, may be subject to federal, state and/or
local reporting requirements. This product and/or its constituents may also be subject to other regulations
at the state and/or local level. Consult those regulations applicable to your facility/operation.
CLEAN WATER ACT (OIL SPILLS)
Any spill or release of this product to "navigable waters" (essentially any surface water, including certain
wetlands) or adjoining shorelines sufficient to cause a visible sheen or deposit of a sludge or emulsion
must be reported immediately to the National Response Center (1-800-424-8802) or, if not practical, the
U.S. Coast Guard with follow-up to the National Response Center, as required by U.S. Federal Law. Also
contact appropriate state and local regulatory agencies as required.
Revision Date: 02/28/01 Page 5 of 7
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
CERCLA SECTION 103 and SARA SECTION 304 (RELEASE TO THE ENVIRONMENT)
The CERCLA definition of hazardous substances contains a "petroleum exclusion" clause which exempts
crude oil, refined, and unrefined petroleum products and any indigenous components of such. However,
other federal reporting requirements (e.g., SARA Section 304 as well as the Clean Water Act if the spill
occurs on navigable waters) may still apply.
SARA SECTION 311/312 - HAZARD CLASSES
ACUTE HEALTH CHRONIC HEALTH FIRE SUDDEN RELEASE OF PRESSURE REACTIVE
X X X -- --
SARA SECTION 313 - SUPPLIER NOTIFICATION
This product may contain listed chemicals below the de minimis levels which therefore are not subject to
the supplier notification requirements of Section 313 of the Emergency Planning and Community Right-To-
Know Act (EPCRA) of 1986 and of 40 CFR 372. If you may be required to report releases of chemicals
listed in 40 CFR 372.28, you may contact Amerada Hess Corporate Safety if you require additional
information regarding this product.
CANADIAN REGULATORY INFORMATION (WHMIS)
Class B, Division 3(Combustible Liquid); Class D, Division 2, Subdivision B (Toxic by other means)
16. OTHER INFORMATION (rev. Feb-01)
NFPA?HAZARD RATING HEALTH: 0 Negligible
FIRE: 2 Moderate
REACTIVITY: 0 Negligible
HEALTH: 1* Slight
HMIS?HAZARD RATING
FIRE: 2 Moderate
REACTIVITY: 0 Negligible
* Chronic
SUPERSEDES MSDS DATED: 09/03/98
ABBREVIATIONS:
AP = Approximately < = Less than > = Greater than
N/A = Not Applicable N/D = Not Determined ppm = parts per million
ACRONYMS:
ACGIH American Conference of Governmental NFPA National Fire Protection Association
Industrial Hygienists (617) 770-3000
AIHA American Industrial Hygiene Association NIOSH National Institute of Occupational Safety
ANSI American National Standards Institute (212) and Health
642-4900 NOIC Notice of Intended Change (proposed
API American Petroleum Institute change to ACGIH TLV)
(202) 682-8000 NTP National Toxicology Program
CERCLA Comprehensive Emergency Response, OPA Oil Pollution Act of 1990
Compensation, and Liability Act OSHA U.S. Occupational Safety & Health
DOT U.S. Department of Transportation Administration
[General info: (800) 467-4922] PEL Permissible Exposure Limit (OSHA)
EPA U.S. Environmental Protection Agency RCRA Resource Conservation and Recovery
HMIS Hazardous Materials Information System Act
IARC International Agency For Research On REL Recommended Exposure Limit (NIOSH)
Cancer SARA Superfund Amendments and
MSHA Mine Safety and Health Administration Reauthorization Act of 1986 Title III
SCBA Self-Contained Breathing Apparatus
Revision Date: 02/28/01 Page 6 of 7
MATERIAL SAFETY DATA SHEET
No. 2 Fuel Oil MSDS No. 0088
SPCC Spill Prevention, Control, and TWA Time Weighted Average (8 hr.)
Countermeasures WEEL Workplace Environmental Exposure
STEL Short-Term Exposure Limit (generally 15 Level (AIHA)
minutes) WHMIS Canadian Workplace Hazardous
TLV Threshold Limit Value (ACGIH) Materials Information System
TSCA Toxic Substances Control Act
DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIES
Information presented herein has been compiled from sources considered to be dependable, and is accurate and reliable to the
best of our knowledge and belief, but is not guaranteed to be so. Since conditions of use are beyond our control, we make no
warranties, expressed or implied, except those that may be contained in our written contract of sale or acknowledgment.
Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety
procedures are not adhered to as stipulated in the data sheet. Additionally, vendor assumes no responsibility for injury to vendee
or third persons proximately caused by abnormal use of the material, even if reasonable safety procedures are followed.
Furthermore, vendee assumes the risk in their use of the material.
Revision Date: 02/28/01 Page 7 of 7
|