ColorLineTM/UnisubTM FRP MSDS No: 00027 Date: 02/20/2006 Page 1 of 4
ColorLineTM/UnisubTM FRP
Material Safety Data Sheet
1. PRODUCT AND COMPANY IDENTIFICATION
Rowmark, Inc. EMERGENCY PHONE NUMBERS:
2040 Industrial Drive Medical: 911
Findlay, OH 45840 Poison Control: 800-589-3897
USA
Telephone Numbers Phone Number Available Hours
Rowmark Customer Service 1-877-ROWMARK 7:00am-5:00pm EST
International 419-425-8974
Product Name: ColorLineTM/UnisubTM FRP
Product Synonym(s): Fiberglass Reinforced Polyester
Chemical Family: Polyester Polymer
Chemical Formula:
Chemical Name: Fiberglass Reinforced Polyester
EPA Reg Number:
Product Use: Signage, Other
2. COMPOSITION / INFORMATION ON INGREDIENTS
Ingredient Name CAS Registry Number Typical Wt. % OSHA
1,3 Dichloropropane 142-28-9
Acetone 67-64-1
Chlorobenzene 108-90-7
Ethyl Methacrylate 97-63-2
Hexachlorobutadiene 87-68-3
Isopropyl Benzene 98-82-8
n-Propylbenzene 103-65-1
Butylbenzene 98-06-6
Toluene 108-88-3
Trichlorofluromethane 75-69-4
Xylene 1330-20-7
The substance(s) marked with a "Y" in the OSHA column are identified as hazardous
chemicals according to the criteria of the OSHA Hazardous Communication Standard (29
CFR 1910.1200).
While this material is not classified as hazardous under Federal OSHA regulations, this
MSDS contains valuable information critical to the safe handling and proper use of this
product. This MSDS should be retained and available for employees and other users of
this product.
The components of this product are all on the TSCA Inventory list.
ColorLineTM/UnisubTM FRP MSDS No: 00027 Date: 02/20/2006 Page 2 of 4
3. HAZARDS INDENTIFICATION
Emergency Overview:
APPEARANCE: Various colors; Characteristic odor
Potential Health Effects:
EYE: Solid or dust may cause irritation or corneal injury due to mechanical action.
SKIN: Essentially non-irritating to the skin. Mechanical injury only. Under normal
processing conditions, material is heated to elevated temperatures; contact with the
material may cause thermal burns. No adverse effects anticipated by skin absorption.
INGESTION: Very low toxicity if swallowed. Harmful effects not anticipated from
swallowing small amounts.
INHALATION: Dust may cause irritation to upper respiratory tract (nose and throat).
4. FIRST AID MEASURES
IF IN EYES: Flush eyes with plenty of water; remove contact lenses after the first 1-2
minutes then continue flushing for several minutes. Only mechanical effects expected.
IN CASE OF CONTACT: If molten material comes in contact with the skin, do not apply
ice but cool under ice water or running stream of water. DO NOT attempt to remove the
material from skin. Removal could result in severe tissue damage.
IF INHALED: Move person to fresh air; if effects occur, consult a physician.
5. FIRE FIGHTING MEASURES
Fire and Explosive Properties
Auto-Ignition Temperature: 800 Degrees F ASTM D 1929
Flash Point: N/A
Flammable Limits: Upper: N/A
Lower: N/A
EXTINGUISHING MEDIA:
Use water spray, carbon dioxide or dry chemical.
FIRE FIGHTING INSTRUCTIONS:
Fire fighters and others who may be exposed to products of combustion should wear full
fire fighting turn out gear (full Bunker Gear) and self-contained breathing apparatus
(pressure demand NIOSH approved or equivalent). Fire fighting equipment should be
thoroughly decontaminated after use.
FIRE AND EXPLOSION HAZARDS:
Heated material can form flammable vapors with air.
6. ACCIDENTAL RELEASE MEASURES
PROTECT PEOPLE: Chips or dust may present a slipping hazard.
CLEANUP: Sweep up chips or dust in a waste disposal container. Flush area with water.
ColorLineTM/UnisubTM FRP MSDS No: 00027 Date: 02/20/2006 Page 3 of 4
7. HANDLING AND STORAGE
HANDLING: Good housekeeping and controlling dusts are necessary for safe handling of
product. Workers should be protected from the possibility of contact with molten resin
during fabrication. Large masses of molten polymer held at elevated temperatures for
extended periods of time may auto-ignite.
STORAGE: Store horizontally in a dry place.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS: Adequate ventilation in work area is needed due to dust or
vapors created during fabrication.
PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION: Safety glasses or face shield should be used. If exposed
to dust, chemical glasses may be required.
SKIN PROTECTION: No precautions other than clean body-covering clothing should
be needed. Use insulated gloves for thermal protection, when desired.
RESPIRATORY PROTECTION: In dusty atmospheres, use an approved respirator.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE/ODOR: Various colors, characteristic odor
BOILING POINT: N/A
VAPOR PRESSURE: N/A
VAPOR DENSITY: N/A
SPECIFIC GRAVITY: 1.2 ?1.8
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY: Stable
CONDITIONS TO AVOID: None known
11. TOXICOLOGY INFORMATION
No data available
12. ECOLOGICAL INFORMATION
MOVEMENT & PARTITIONING: In the terrestrial environment, material is expected to
remain in the soil. In the aquatic environment, material will sink and remain in the
sediment.
DEGRADATION & PERSISTENCE: This water insoluble polymeric solid is expected to be
inert in the environment. Surface photo degradation is expected with exposure to sunlight.
No appreciable biodegradation is expected.
ECOTOXICITY: Not expected to be acutely toxic, but chips may mechanically cause
adverse effects if ingested by waterfowl or aquatic life.
ColorLineTM/UnisubTM FRP MSDS No: 00027 Date: 02/20/2006 Page 4 of 4
13. DISPOSAL CONSIDERATIONS
Disposal must be in accordance with applicable governmental regulations.
14. TRANSPORT INFORMATION
No data available
15. REGULATORY INFORMATION
(Not meant to be all-inclusive ?selected regulations represented)
NOTICE: The information herein is presented in good faith and believed to be accurate as
of the effective date shown above. However, no warranty, express or implied is given.
Regulatory requirements are subject to change and may differ from one location to
another; it is the buyer's responsibility to ensure that its activities comply with federal,
state or provincial, and local laws. The following specific information is made for the
purpose of complying with numerous federal, state or provincial, and local laws and
regulations. See other sections for health and safety information.
U.S. REGULATIONS
No data available
CANADIAN REGULATIONS
No data available
16. OTHER INFORMATION
NFPA HAZARD RATING (National Fire Protection Association):
FIRE: Materials that must be preheated before ignition can
Fire occur.
1 HEALTH: Materials that under emergency conditions would
Health 0 0 Reactivity offer no hazard beyond that of ordinary
? combustible materials.
Special REACTIVITY: Materials that in themselves are normally
stable, even under fire exposure conditions.
The actual sublimation process emits extremely small amounts of 1,3 Dichloropropane,
Acetone, Chlorobenzene Ethyl Methacrylate, Hexachlorobutadiene, Isopropyl Benzene, n-
Butylbenzene, n-Propylbenzene, Butylbenzene, Toluene, Trichlorofluromethane, Xylene
REASON FOR ISSUE:
The information herein is given in good faith, but no warranty, express or implied, is made. Consult Rowmark, Inc. for
further information.
|