MATERIAL SAFETY 3M
DATA SHEET 3M Center
St. Paul, Minnesota
55144-1000
1-800-364-3577 or (651) 737-6501 (24 hours)
Copyright, 2000, Minnesota Mining and Manufacturing Company.
All rights reserved. Copying and/or downloading of this
information for the purpose of properly utilizing 3M products
is allowed provided that:
1) the information is copied in full with no changes unless
prior agreement is obtained from 3M, and
2) neither the copy nor the original is resold or otherwise
distributed with the intention of earning a profit thereon.
DIVISION: AUTOMOTIVE AFTERMARKET
TRADE NAME:
3M FINESSE-IT II Finishing Material P/N 05927, 05928, 05929, 05932
ID NUMBER/U.P.C.:
60-9800-1029-6 00-51131-05928-3 60-9800-1131-0 00-51131-05929-0
60-9800-1525-3 00-51131-05932-0 60-9800-2090-7 00-51131-06049-4
CN-1006-9451-8 - - -
ISSUED: October 24, 2000
SUPERSEDES: October 05, 2000
DOCUMENT: 11-0395-1
-----------------------------------------------------------------------------
1. INGREDIENT C.A.S. NO. PERCENT
-----------------------------------------------------------------------------
WATER................................... 7732-18-5 50.0 - 75.0
HYDROTREATED HEAVY NAPHTHA (PETROLEUM).. 64742-48-9 5.0 - 15.0
ALUMINUM OXIDE.......................... 1344-28-1 5.0 - 15.0
DISTILLATES (PETROLEUM), ACID TREATED,
LIGHT................................. 64742-14-9 5.0 - 15.0
GLYCERIN................................ 56-81-5 1.0 - 5.0
The components of this product are in compliance with the chemical
notification requirements of TSCA.
-----------------------------------------------------------------------------
2. PHYSICAL DATA
-----------------------------------------------------------------------------
BOILING POINT:................. >200
VAPOR PRESSURE:................ <1 MM HG
VAPOR DENSITY:................. 4.50 Air=1
EVAPORATION RATE:.............. N/D
SOLUBILITY IN WATER:........... DISPERSABLE
SPECIFIC GRAVITY:.............. 1 Water=1
PERCENT VOLATILE:.............. 85 - 90 % by wt
pH:............................ 8.0 - 8.3
VISCOSITY:..................... 12K - 18K CPS
MELTING POINT:................. N/D
-----------------------------------------------------------------------------
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M FINESSE-IT II Finishing Material P/N 05927, 05928, 05929, 05932
October 24, 2000 PAGE 2
-----------------------------------------------------------------------------
2. PHYSICAL DATA (continued)
-----------------------------------------------------------------------------
APPEARANCE AND ODOR:
Liquid, white, no odor
-----------------------------------------------------------------------------
3. FIRE AND EXPLOSION HAZARD DATA
-----------------------------------------------------------------------------
FLASH POINT:................... > 200.00 F
ASTM Method D93
FLAMMABLE LIMITS - LEL:........ 0.7%
FLAMMABLE LIMITS - UEL:........ 7.0%
AUTOIGNITION TEMPERATURE:...... N/D
EXTINGUISHING MEDIA:
Water spray, Carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES:
Wear full protective clothing, including helmet, self-contained,
positive pressure or pressure demand breathing apparatus, bunker coat
and pants, bands around arms, waist and legs, face mask, and
protective covering for exposed areas of the head.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
None known.
NFPA HAZARD CODES: HEALTH: 1 FIRE: 1 REACTIVITY: 0
UNUSUAL REACTION HAZARD: none
-----------------------------------------------------------------------------
4. REACTIVITY DATA
-----------------------------------------------------------------------------
STABILITY: Stable
INCOMPATIBILITY - MATERIALS/CONDITIONS TO AVOID:
None known.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon Monoxide and Carbon Dioxide, Toxic Vapors, Gases or
Particulates.
-----------------------------------------------------------------------------
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M FINESSE-IT II Finishing Material P/N 05927, 05928, 05929, 05932
October 24, 2000 PAGE 3
-----------------------------------------------------------------------------
5. ENVIRONMENTAL INFORMATION
-----------------------------------------------------------------------------
SPILL RESPONSE:
Observe precautions from other sections. Contain spill. Cover with
absorbent material. Collect spilled material. Clean up residue with
water. Place in a closed container.
RECOMMENDED DISPOSAL:
Incinerate in an industrial or commercial facility in the presence of
a combustible material.
ENVIRONMENTAL DATA:
Not determined.
REGULATORY INFORMATION:
Volatile Organic Compounds: 1.92 lb/gal calculated per SCAQMD rule 443.1.
Volatile Organic Compounds: 230 gms/liter calculated per SCAQMD rule
443.1.
VOC Less H2O & Exempt Solvents: 638 gms/liter calculated per SCAQMD rule
443.1.
Since regulations vary, consult applicable regulations or authorities
before disposal. U.S. EPA Hazardous Waste Number = None (Not U.S.
EPA Hazardous).
EPCRA HAZARD CLASS:
FIRE HAZARD: No PRESSURE: No REACTIVITY: No ACUTE: Yes CHRONIC: No
-----------------------------------------------------------------------------
6. SUGGESTED FIRST AID
-----------------------------------------------------------------------------
EYE CONTACT:
Immediately flush eyes with large amounts of water. Get immediate
medical attention.
SKIN CONTACT:
Flush skin with large amounts of water. If irritation persists, get
medical attention.
INHALATION:
If signs/symptoms occur, remove person to fresh air. If
signs/symptoms continue, call a physician.
IF SWALLOWED:
Do not induce vomiting. Drink two glasses of water. Call a physician.
-----------------------------------------------------------------------------
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M FINESSE-IT II Finishing Material P/N 05927, 05928, 05929, 05932
October 24, 2000 PAGE 4
-----------------------------------------------------------------------------
7. PRECAUTIONARY INFORMATION
-----------------------------------------------------------------------------
EYE PROTECTION:
Avoid eye contact.
SKIN PROTECTION:
Avoid prolonged or repeated skin contact. Wear appropriate gloves
when handling this material. A pair of gloves made from the
following material(s) are recommended: nitrile rubber, polyvinyl
alcohol, fluoroelastomer (Viton).
RECOMMENDED VENTILATION:
Use in a well-ventilated area. Provide sufficient ventilation to
maintain emissions below recommended exposure limits.
RESPIRATORY PROTECTION:
Avoid prolonged breathing of vapors.
PREVENTION OF ACCIDENTAL INGESTION:
Wash hands after handling and before eating. Do not ingest.
RECOMMENDED STORAGE:
Keep container closed when not in use. Keep out of the reach of
children.
FIRE AND EXPLOSION AVOIDANCE:
Keep container tightly closed. Keep away from heat, sparks, open
flame, and other sources of ignition.
EXPOSURE LIMITS
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
-----------------------------------------------------------------------------
WATER................................ NONE NONE NONE NONE
HYDROTREATED HEAVY NAPHTHA
(PETROLEUM)........................ 100 PPM TWA 3M
HYDROTREATED HEAVY NAPHTHA
(PETROLEUM)........................ 300 PPM TWA CMRG
ALUMINUM OXIDE....................... 1.0 FIBER/CC TWA CMRG
ALUMINUM OXIDE....................... 1.0 FIBER/CC TWA OSHA
PROPOSED
ALUMINUM OXIDE....................... 10 MG/M3 TWA OSHAV
AS DUST
OSHA VACATED PEL: TOTAL DUST
ALUMINUM OXIDE....................... 10 MG/M3 TWA ACGIH
as Al
ALUMINUM OXIDE....................... 15 MG/M3 TWA OSHA
AS DUST
TOTAL DUST
ALUMINUM OXIDE....................... 5 MG/M3 TWA OSHA
AS DUST
-----------------------------------------------------------------------------
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M FINESSE-IT II Finishing Material P/N 05927, 05928, 05929, 05932
October 24, 2000 PAGE 5
EXPOSURE LIMITS (continued)
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
-----------------------------------------------------------------------------
RESPIRABLE FRACTION
DISTILLATES (PETROLEUM), ACID
TREATED, LIGHT..................... NONE NONE NONE NONE
GLYCERIN............................. 10 MG/M3 TWA ACGIH
AS MIST
GLYCERIN............................. 10 MG/M3 TWA OSHAV
AS MIST
OSHA VACATED PEL: TOTAL DUST
GLYCERIN............................. 15 MG/M3 TWA OSHA
AS MIST
TOTAL DUST
GLYCERIN............................. 5 MG/M3 TWA OSHA
AS MIST
RESPIRABLE FRACTION
* SKIN NOTATION: Listed substances indicated with 'Y' under SKIN refer to
the potential contribution to the overall exposure by the cutaneous route
including mucous membrane and eye, either by airborne or, more particularly,
by direct contact with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA:
- 3M: 3M Recommended Exposure Guidelines
- ACGIH: American Conference of Governmental Industrial Hygienists
- CMRG: Chemical Manufacturer Recommended Exposure Guidelines
- OSHA: Occupational Safety and Health Administration
- OSHAV: Occupational Safety and Health Administration Vacated PEL.
Vacated Permissible Exposure Limits (PEL) are enforced as
the OSHA PEL in some states. Check with your local
regulatory authority.
- NONE: None Established
-----------------------------------------------------------------------------
8. HEALTH HAZARD DATA
-----------------------------------------------------------------------------
EYE CONTACT:
Mild Eye Irritation: signs/symptoms can include redness, swelling,
pain, and tearing.
SKIN CONTACT:
Mild Skin Irritation (after prolonged or repeated contact):
signs/symptoms can include redness, swelling, and itching.
INHALATION:
Irritation (upper respiratory): signs/symptoms can include soreness
of the nose and throat, coughing and sneezing.
Prolonged or repeated overexposure, above recommended guidelines, may
cause:
-----------------------------------------------------------------------------
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M FINESSE-IT II Finishing Material P/N 05927, 05928, 05929, 05932
October 24, 2000 PAGE 6
-----------------------------------------------------------------------------
8. HEALTH HAZARD DATA (continued)
-----------------------------------------------------------------------------
Central Nervous System Depression: signs/symptoms can include
headache, dizziness, drowsiness, incoordination, slowed reaction
time, slurred speech, giddiness and unconsciousness.
IF SWALLOWED:
Ingestion may cause:
Irritation of Gastrointestinal Tissues: signs/symptoms can
include pain, vomiting, abdominal tenderness, nausea, blood in
vomitus, and blood in feces.
Central Nervous System Depression: signs/symptoms can include
headache, dizziness, drowsiness, muscular weakness,
incoordination, slowed reaction time, fatigue, blurred vision,
slurred speech, giddiness, tremors and convulsions.
-----------------------------------------------------------------------------
SECTION CHANGE DATES
-----------------------------------------------------------------------------
PRECAUTIONARY INFO. SECTION CHANGED SINCE October 05, 2000 ISSUE
-----------------------------------------------------------------------------
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
-----------------------------------------------------------------------------
The information in this Material Safety Data Sheet (MSDS) is believed to
be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining
whether the 3M product is fit for a particular purpose and suitable for
user's method of use or application. Given the variety of factors that
can affect the use and application of a 3M product, some of which are
uniquely within the user's knowledge and control, it is essential that
the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers.
Due to the remote possibility that electronic transfer may have resulted
in errors, omissions or alterations in this information, 3M makes no
representations as to its completeness or accuracy. In addition,
information obtained from a database may not be as current as the
information in the MSDS available directly from 3M.
|