Material Safety Data Sheet
Omni Specialty Packaging
For Compliance with OSHA 29 CFR 1910.1200 and ANSI Z400.1-1998
1. Product and Company Identification
Product Name MSDS Code Number
STIHL 2-CYCLE HP ENGINE OIL
Trade Name & Synonyms Date of Last Revision
2/22/2008
Chemical Name Manufacturer
Omni Specialty Packaging
C.A.S. Number Address
10399 Hwy. 1
Grades or Minor Variant Identities Information Telephone Number
(318) 524-1100
Foreign Emergency Telephone Number
Product Use (for Canada) Emergency Telephone Number
(318) 524-1100
2. Composition/Information on Ingredients
Hazardous Components C.A.S Number Exposure Limits Oil Mist %
5 mg/m3
Petroleum Distillates, Hydrotreated Heavy Paraffinic 64742-54-7 Blend
5 mg/m3
Petroleum Distillates, Solvent Dewaxed heavy Paraffinic 64742-65-0 Blend
3
Residual Oils (petroleum). Solvent Dewaxed 64742-62-7 5 mg/m Blend
3
RESIDUAL Oils (petroleum), Hydrotreated 64742-57-0 5 mg/m Blend
3
Stoddard Solvent 8052-41-3 525 mg/m 8
Additive Package Mixture N/A <7
Dye Mixture N/A 0.14
OSHA Regulatory Status
29 CFR 1910.1200.
3. Hazards Identification
Emergency Overview
This product is considered not hazardous under 29 CFR 1910.1200 (Hazard Communication).
Routes of Signs and Symptoms Single, Repeated, or Severity (Mild, Acute and Target
Exposure Lifetime Exposures Moderate, Chronic Organ(s)
Severe) Health
Effect(s)
Eye Practically non- irritating to the eye upon direct contact.
Skin Minimally irritating upon direct contact. May cause
irritation/dermatitis.
Inhalation Low hazard at standard temperatures and pressures.
Inhalation of oil mist or fumes can cause irritation of the
nose, throat and upper respiratory tract
Ingestion Don not ingest. May cause nausea, vomiting/diarrhea.
Other On rare occasions, prolonged and repeated exposure to oil
mist poses a risk of pulmonary disease such as chronic lung
inflammation. This condition is usually asymptomatic as a
result of repeated small aspirations.
MSDS 鈥? OMNI SPECIALTY PACKAGING
Medical Conditions Aggravated by Exposure
Personnel with pre-existing skin disorders should avoid contact with this product.
4. First Aid Measures
Routes of Exposure First Aid Instructions Immediate Medical Attention Delayed
Eye Flush with large amount of water for 15 minutes. Get medical If material is hot, treat for thermal
attention if eye irritation develops or persists. burns and take victim to the
hospital immediately.
Skin Wash with soap and water. Remove contaminated clothes and wash
before reuse. Get medical attention if skin discolor develop.
Inhalation This material is not expected to present an inhalation exposure at
ambient conditions
Ingestion Do not induce vomiting. Get immediate medical attention or advice.
Other Not available
Note to Physicians (Treatment, Testing, and Monitoring)
Not available
5. Fire Fighting Measures
Flashpoint Flammable (Explosive) Limits in Air Autoignition Hazard rating
Method: 掳F LEL UEL Temperature 掳F
PMCC 170 Not determined Not determined N/A N/A Fire 1
Health 0
Flame Propagation or Burning Rate Properties Contributing to Fire Flammability
(for solids) Intensity Classification
reactivity 0
Not Available Not Determined Not Available
Extinguishing Media Extinguishing Media to Avoid Reactions to Extinguishing Media
Water for, foam, CO2, dry chemical Not Available Not Available
Protection and Procedures for Firefighters
Wear positive pressure self-contained breathing apparatus (SCUBA). Use water to cool containers exposed to flames. Structural firefighters鈥?
protective clothing will only provide limited protection.
Unusual Fire and Explosion Hazards
Mist or sprays may be flammable below the product normal flash point.
6. Accidental Release Measures
Spill/Leak Clean-up Procedures and Equipment
Observing health hazards described above, ventilate area. Dike to contain spill. Pick up free liquid for recycle and/or disposal. Residual liquid
and/or solid can be absorbed on inert material. Keep from sewers and natural water.
Evacuation Procedures
Large spill
* Consider initial downwind evacuate for at least 300 meters (1000 feet).
Fire
* If tank, rail car or tank car is involved in a fire, isolate for 800 meters (1/2 mile) in all directions; also consider initial evacuation for 800
meters (1/2 mile) in all directions.
Special Instructions
When using this material, do not eat, drink, or smoke. Wash thoroughly after handling. Keep away from animals and children.
Reporting Requirements
Spills that enter a water body must be reported immediately to the USEPA鈥檚 National Response Center at (800)546-2972. Check with your local
and state regulators regarding their reporting requirements.
7. Handling and Storage
Handling Practices and Warnings
Do not pressure, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of
ignition; they may explode. See NFPA 30 and OSHA 1910.106 鈥? flammable and combustible liquids.
Storage Practices and Warnings
Store away from heat, sparks, open flame, or strong oxidizing agents in closed and properly labeled containers. Empty containers retain product
residue (liquid, and/or vapor) and can be dangerous.
Page 2 of 6
MSDS 鈥? OMNI SPECIALTY PACKAGING
8. Exposure Control/Personal Protection
Other Engineering controls Ventilation
N/A Additional area ventilation or local exhaust may be required to maintain air concentrations below recommended limits.
Routes of Entry: Personal Protective Equipment (PPE) for Normal Use: PPE for Emergencies
Eye/Face Safety glasses or face shield where splashing is possible. Full face shield
Skin As needed to prevent repeated skin contact. Solvent resistant
gloves should be used if needed.
Inhalation Not normally needed. Respirator
9. Physical and Chemical Properties
Appearance Odor
Blue Liquid Mild petroleum odor
Normal Physical State: Boiling Point N/A 掳F
Melting Point N/A
x 掳F
Liquid Gas
Freezing Point 0 掳F
Solid (Other)
Specific Gravity or Density (H20 = 1) Solubility in Water pH
Negligible N/A
0.87
Vapor Density (AIR = 1) Evaporation Rate (Butyl Acetate = 1)
Vapor Pressure (mm Hg.)
Not Determined Not Available
<0.01
Other
N/A
10. Stability and Reactivity
Incompatibility (Materials to Avoid)
Heat, open flame, and oxidizing agents.
Hazardous Products Produced During Decomposition
Combustion products may include smoke, fumes, oxides of phosphorus, boron, sulfur, nitrogen, carbon dioxide, carbon monoxide, and other low
molecular weight hydrocarbons.
Conditions to Avoid
X
Hazardous Polymerization? May Occur Will Not Occur
Conditions to Avoid
Sources of ignition
X
Stability? Stable Unstable
11. Toxicological Information
Toxicity Data, Epidemiology Studies, Carcinogenicity, Neurological Effects, Genetic Effects, Reproductive Effects, or Structure Activity Data
Acute Toxicity: Test on similar materials show a low order of acute oral and dermal toxicity.
Acute Oral Effects: Test on similar materials indicates low order of acute toxicity.
Acute Inhalation Effects: Low acute toxicity expected on inhalation.
Skin Effects: Practically non-toxic if absorbed. Other similar highly refined products have not shown skin tumors in mouse skin painting studies.
Eye Irritation: Minimal irritation on contact. Eye irritation slightly or practically non-irritating base on similar products.
Carcinogenicity:
Skin: Not considered a potential carcinogen base on IP346 DMSO of less tan 3.0 wt%
Genotoxicity: This product is considered non-mutagenic and has negative potential for tumor development based on from Modified Ames Assay, with Mutagenic
Index of less than 1.0.
Page 3 of 6
MSDS 鈥? OMNI SPECIALTY PACKAGING
12. Ecological Information
Toxicity, Environmental Fate, Physical/Chemical Data, or Other Data Supporting Environmental Hazard Statements
If applied to leaves, this product may kill grasses and small plants by interfering with transpiration and respiration. This product is not toxic to
fish but may coat gill structures resulting in suffocation if spilled in shallow, running water. Product may be moderately toxic to amphibians
by preventing dermal respiration. This product may cause gastrointestinal distress to birds and mammals through ingestion during pelage
grooming.
13. Disposal Considerations
Regulations
Dispose in accordance with all local, state, and federal regulations. Keep this product out of sewers and waterways.
Note: State or local requirements may differ from federal regulations. Processing or using this product may make the information here inappropriate. Waste
generators are responsible for waste classification, transport, and disposal.
14. Transport Information
Regulated for shipping? Proper Shipping Name Packing Group
N/A N/A
Yes X No
Do changes in quantity, packaging, or shipment Hazard Class Identification Number
method change product qualification?
N/A N/A
Yes x No
Other
N/A
Page 4 of 6
MSDS 鈥? OMNI SPECIALTY PACKAGING
15. Regulatory Information
Federal Regulations (OSHA, TSCA, CERCLA, FIFRA, EPCRA, CAA, CWA, SDWA, CPSA, DEA, FDA/USDA, etc.)
State Regulations
U.S. Federal Regulatory Information:
CERCLA/SARA
302/303/304 Categories: Extremely Hazardous Substances No
(40 CFR 355 Appendix A)
311/312 Categories: Immediate (Acute) Health Effects No
(40 CFR 370) Delayed (Chronic) Health Effects No
Fire Hazard No
Sudden Release of Pressure Hazard No
Reactivity Hazard No
313 Categories: Toxic Chemicals (40 CFR 372) No
Clean Air Act: Hazardous Air Pollutants (HAPS) No
Clean Water Act: If spilled into navigable waters it is reportable to National Response Center, 800-424-8802
(40 CFR 116; 401.15) Reportable Quantity = Oil Sheen present on navigable water surface
OSHA (29 CFR 1910): This product is not hazardous under Hazard Communication Standard 29 CFR 1910.1200
RCRA (40 CFR 261.133) This product does not meet hazardous waste criteria.
EPA/TSCA Inventory: The components of this product are listed on the EPA/TSCA inventory of chemicals.
CAS No. 64742-54-7
State Regulations:
California Prop 65 No Proposition 65 chemicals exist in this product, no labeling required.
Florida No listed ingredients are present
Massachusetts RTK No listed ingredients are present
Minnesota RTK No listed ingredients are present
New Jersey RTK Lists petroleum oil, but this product does not contain hazardous ingredients.
Pennsylvania RTK Lists petroleum oil, but this product does not contain hazardous ingredients greater than 3%.
Illinois DOL TSL No listed ingredients are present
Other Regulations:
WHMIS (Canada) Not listed on the Canadian Controlled Product Ingredient Disclosure and is compliant with Controlled Products Regulation
CONEG Metals: Since cadmium, chromium, lead and mercury are not detectable and it does not exceed 100 ppm total in this product, it is compliant with
CONEG Metals regulation.
EEC (Europe): This product is not known to be a dangerous good internationally.
No known R-Phrases or S-Phrases
Hazard Label None
Danger Symbol None
International Regulations
N/A
Other
N/A
Page 5 of 6
MSDS 鈥? OMNI SPECIALTY PACKAGING
16. Other Information
Label Text, Hazard Rating System, Key Legend, or Other
Abbreviations
ACGIH(American Conference of Governmental Industrial Hygienists); ANSI(American National Standards Institute); CAS(Chemical Abstract Service);
CERCLA(Comprehensive Environmental Response, Compensation, & Liability Act); CFR(Code of Federal Regulations); CHIP (Chemicals Hazard Information &
Packaging for Supply); CONCAWE (European Organization for Environment, Health & Safety); CPR(Controlled Products Regulations); DOL (Department of Labor);
EED(European Economic Community Directives); EINECS (European Inventory of Existing Commercial Chemical Substances); EL50 (Effective loading rate required
to immobilize 50% invertebrate species); ELINCS(European List of New Chemical Substances); EPA (Environmental Protection Agency); EPCRA(Emergency
Planning & Community Right-To-Know Act of 1986); EU(European Union); FDA(Food & Drug Administration-USA); GHS (Global Harmonization System); HCS
(Hazard Communication Standard); IARC(International Agency for Research on Cancer); ILO(International Labor Organization); LC50(Lethal Concentration 50%
test organisms); LD50(Lethal Dose 50% test organisms); LVP-VOC(Low Vapor Pressure Volatile Organic Compound); MSDS(Material Safety Data Sheet);
MSHA(Mine Safety & Health Administration); NIOSH(National Institute of Occupational Safety & Health);NTP(National Toxicology Program); OSHA(Occupational
Safety & Health Administration); PEL(Permissible Exposure Limit); Prop 65(California Proposition 65); PMCC(Pensky Martin Closed Cup); RCRA(Resource
Conservation & Recovery Act); RTK(Right-To-Know); R-Phrases(EU Risk Phrases; S-Phrases (EU Safety Phrases); SARA(Superfund Amendments & Reauthorization
Act); TSCA (Toxic Substances Control Act); TSL (Toxic Substance List); TLV(Threshold Limit Value); WHMIS(Workplace Hazardous Materials Information System-
Canada); lrL50 (Inhibitory loading rate required to reduce algal growth rate by 50%; lbL50 (Inhibitory loading rate required to reduce area under growth curve or
biomass by 50%); ppm (parts per million); mg/m3 (milligrams per cubic meter); N(no); Y (yes)
NFPA Hazard Rating 鈥? Health 0 Slight
-Fire 1 Slight
Reactivity 0 Least
Prepared By: Juan Parker Phone: (318) 524-1100
This MSDS complies with OSHA Hazard Communication Standard (HCS) 29 CFR 1910.1200 and conforms to ANSI Z 400.1 16-Section Format.
Disclaimer: Omni Specialty Packaging believes this information is accurate but not all-inclusive in all circumstances. It is the responsibility of the user to determine
suitability of the material for their purposes. No warranty, expressed or implied, is given.
NOTE: OSHA鈥檚 Hazard Communication Standard (29 CFR 1910.1200) does not require the information requested in Sections 11, 12, 13, 4, 15, and 16 for
MSDSs. If your company chooses not to fill in these sections, you may wish to enter something (like N/R for 鈥渘ot regulated鈥? or N/A for 鈥渘ot applicable鈥?) to indicate
that the field is purposely being left blank.
Page 6 of 6
|