MATERIAL SAFETY DATA SHEET
UV CURABLE CLEAR DTM COATING Page: 1
8/5/2009
PRODUCT NAME: UV CURABLE CLEAR DTM COATING
PRODUCT CLASS: UV COATING HMIS CODES:H F R P
PRODUCT CODE: C90-0083U
=====================SECTION I - MANUFACTURER IDENTIFICATION====================
MANUFACTURER'S NAME: STRATHMORE PRODUCTS, INC.
ADDRESS1970 WEST FAYETTE STREET
P.O. BOX 151
SYRACUSE, NY 13201
EMERGENCY PHONE DAY: 315-488-5401
NIGHT: FOR HEALTH - POISON CONTROL CENTER: 315/476-4766
FOR SPILLS - CHEMTEL: 1-800/255-3924
DATE OF PREPARATION: 8/5/2009
TIME OF PREPARATION: 11:07:30 REVISION DATE: 07/28/09
============SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION=============
VAPOR PRESSURE RANGE
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
----------------------------------------------------------------------------------------------------------------------------
CRYSTALLINE SILICA 14808-60-7
ACGIH TLV: 0.05 MG/M3 OSHA PEL: 0.1 MG/M3
2-Hydroxy-2-methyl-1phenyl-1-propanone 7473-98-5 0-2%
TWA/PEL: NOT ESTABLISHED,MFR. 6 mg/m3
1-HYDROXYCYCLOHEXYL PHENYL KETONE 947-19-3 0-2%
ACGIH TLV & OSHA PEL: NOT ESTABLISHED
MFG. RECOMMENDATION: 10 mg/m3
SARA 313 INFORMATION:
*N/A
FOOTNOTE:
SEE MSDS SECTION X.
============SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS=====================
BOILING RANGE OF SEC. II: N/A WEIGHT per GALLON: 9.92 lb/gl
VAPOR DENSITY: HEAVIER THAN AIR
EVAPORATION RATE: SLOWER THAN ETHER % SOLIDS BY VOLUME: 100.
V.O.C.: 0.0 lb/gl
==================SECTION IV - FIRE AND EXPLOSION HAZARD DATA===================
DOT CATEGORY:
NOT REGULATED.
FLASH POINT : >200癋 METHOD USED: SETA FLASH
FLAMMABLE LIMITS IN AIR BY VOLUME-LOWER: N/A
EXTINGUISHING MEDIA:
USE CARBON DIOXIDE OR DRY CHEMICAL MEDIA TO EXTINGUISH SMALL FIRES. FOR LARGE FIRES, APPLY ALCOHOL-TYPE OR ALL-PURPOSE-
TYPE FOAM ACCORDING TO MANUFACTURER'S RECOMMENDED TECHNIQUES.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
MATERIAL SAFETY DATA SHEET
UV CURABLE CLEAR DTM COATING Page: 2
8/5/2009
HIGH TEMPERATURES AND FIRE CONDITIONS MAY CAUSE RAPID AND UNCONTROLLED POLYMERIZATION, WHICH CAN RESULT IN EXPLOSIONS
AND THE VIOLENT RUPTURE OF STORAGE VESSELS OR CONTAINERS. DO NOT DIRECT A STREAM OF WATER OR FOAM INTO HOT, BURNING
POOLS AS THIS MAY CAUSE FROTHING AND INCREASE FIRE INTENSITY.
SPECIAL FIREFIGHTING PROCEDURES:
KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE FROM HEAT, SPARKS, ELECTRICAL EQUIPMENT AND OPEN FLAME. AVOID BREATHING GASES,
VAPORS, FUMES OR DECOMPOSITION PRODUCTS DURING A FIRE. PERSONNEL INVOLVED IN A FIRE SHOULD WEAR FULL PROTECTIVE
EQUIPMENT, INCLUDING SELF-CONTAINED RESPIRATORY EQUIPMENT. WATER SPRAY MAY BE USED TO COOL UNRUPTURED CLOSED CONTAINERS
TO PREVENT PRESSURE BUILDUP AND POSSIBLE AUTOIGNITION OR EXPLOSION WHEN EXPOSED TO EXTREME HEAT. IF WATER IS USED, FOG
NOZZLES ARE PREFERABLE.
=========================SECTION V - HEALTH HAZARD DATA=========================
THRESHOLD LIMIT VALUE: SEE SECTION II
INHALATION HEALTH RISKS AND SYMPTOMS OF ACUTE EXPOSURE:
SHORT TERM HEALTH EFFECTS ARE NOT EXPECTED FROM EXPOSURE TO VAPORS GENERATED AT AMBIENT TEMPERATURES. INHALATION OF
SPRAY MISTS AT AMBIENT TEMPERATURES CAN BE IRRITATING TO THE RESPIRATORY SYSTEM. INHALATION OF VAPORS FROM THE HEATED
PRODUCT CAN CAUSE IRRITATION TO THE RESPIRATORY SYSTEM AND MAY RESULT IN HEADACHES, NAUSEA, AND DIZZINESS.
EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
CONTACT OF LIQUID WITH EYES MAY CAUSE IRRITATION, SEEN AS MILD TO MODERATE REDNESS AND SWELLING OF THE CONJUNCTIVA.
VAPORS FROM HEATED PRODUCT MAY CAUSE EYE IRRITATION.
SKIN CONTACT HEALTH RISKS AND SYMTOMS OF EXPOSURE:
THIS PRODUCT CONTAINS MATERIALS THAT MAY CAUSE MODERATE REDDENING AND SWELLING OF THE SKIN AND POSSIBLE SENSITIZATION.
AVOID SKIN CONTACT IN SUNLIGHT.
REPEATED OR PROLONGED SKIN CONTACT MAY CAUSE IRRITATION AND BLISTER FORMATION (BURNS). SINCE IRRITATION MAY NOT OCCUR
IMMEDIATELY, CONTACT CAN GO UNNOTICED.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
SLIGHTLY TO MODERATELY TOXIC. MAY CAUSE ABDOMINAL DISCOMFORT, NAUSEA, AND VOMITING.
CHRONIC HEALTH HAZARDS:
PROLONGED OR REPEATED EXPOSURE TO VAPOR GENERATED AT HIGH TEMPERATURES, OR TO AEROSOLS OR MIST GENERATED UNDER AMBIENT
CONDITIONS, MAY RESULT IN THE INHALATION OF HARMFUL AMOUNTS OF MATERIAL, WHICH MAY CAUSE LIVER AND KIDNEY EFFECTS AND
RESPIRATORY IRRITATION.
CARCINOGENICITY:
THIS PRODUCT CONTAINS CRYSTALLINE SILICA, WHICH IN ITS DRY FORM IS CONSIDERED A HAZARD BY INHALATION. SILICA IS THE
MOST COMMON MINERAL ON THE FACE OF THE EARTH AND IS A PRIMARY CONSTITUENT OF BEACH SAND. ALMOST ALL NATURAL MATERIALS
CONTAIN CRYSTALLINE SILICA, AND AT LEVELS OF 0.1% OR MORE, REQUIRE AN OSHA WARNING. CRYSTALLINE SILICA HAS BEEN
CLASSIFIED BY IARC AS GROUP 2A (PROBABLY CARCINOGENIC TO HUMANS). THIS CLASSIFICATION IS BASED ON THE FINDINGS OF
LABORATORY ANIMAL STUDIES THAT WERE SUFFICIENT AND DATE FROM EPIDEMIOLOGICAL (HUMAN) STUDIES THAT WERE CONSIDERED
LIMITED FOR CARCINOGENICITY. NTP HAS CLASSIFIED CRYSTALLINE SILICA AS AN ANTICIPATED CARCINOGEN. ACGIH STATES THAT
CRYSTALLINE SILICA HAS BEEN IDENTIFIED BY OTHER SOURCES AS A SUSPECTED OR CONFIRMED HUMAN CARCINOGEN. OSHA HAS NOT
CLASSIFIED CRYSTALLINE SILICA. CRYSTALLINE SILICA IS ALSO A KNOWN CAUSE OF SILICOSIS, A NON-CANCEROUS LUNG DISEASE. IT
IS IMPORTANT THAT THE PROPER RESPIRATORY EQUIPMENT BE WORN DURING SPRAY APPLICATION OR SANDING OF THIS PRODUCT WHEN THE
TLV'S, AS SHOWN IN SECTION II, ARE EXCEEDED.
MATERIAL SAFETY DATA SHEET
UV CURABLE CLEAR DTM COATING Page: 3
8/5/2009
EMERGENCY FIRST AID PROCEDURES:
INHALATION: REMOVE TO FRESH AIR. IF BREATHING HAS STOPPED, GIVE ARTIFICIAL RESPIRATION AND GET IMMEDIATE MEDICAL
ATTENTION. EYE CONTACT: IMMEDIATELY FLUSH EYES WITH COPIOUS QUANTITIES OF RUNNING WATER FOR 15 MINUTES, LIFTING THE
UPPER AND LOWER EYELIDS OCCASIONALLY, AND GET IMMEDIATE MEDICAL ATTENTION. SKIN CONTACT: REMOVE CONTAMINATED CLOTHING
AND SHOES. IMMEDIATELY WASH AFFECTED AREA WITH SOAP AND WATER. IF IRRITATION PERSISTS AFTER WASHING, GET MEDICAL
ATTENTION (EFFECTS CAN BE DELAYED 24-48 HOURS). WASH CONTAMINATED CLOTHING BEFORE REUSE AND DISCARD ANY LEATHER
ARTICLES SUCH AS SHOES.
INGESTION: IF SWALLOWED, GET MEDICAL HELP IMMEDIATELY. IF PERSON IS CONSCIOUS, GIVE 2 GLASSES OF WATER BUT DO NOT
INDUCE VOMITING UNLESS DIRECTED BY A PHYSICIAN. DO NOT GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS OR CONVULSIVE PERSON.
HAVE PHYSICIAN DETERMINE WHETHER VOMITING OR STOMACH EVACUATION IS NECESSARY.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
NOT KNOWN.
==========================SECTION VI - REACTIVITY DATA==========================
STABILITY:
NORMALLY STABLE AT NORMAL ROOM TEMPERATURE.
CONDITIONS TO AVOID:
AVOID EXPOSURE TO ULTRAVIOLET LIGHT, SUNLIGHT, STRONG BASES, PEROXIDES, STORING AT TEMPERATURES ABOVE 100F, AND EXPOSURE
TO HIGH HEAT.
INCOMPATIBILITY (MATERIALS TO AVOID):
PEROXIDES, AMINES, COPPER, COPPER ALLOY, CARBON STEEL, IRON, RUST, AND STRONG ACIDS, BASES AND OXIDIZING AGENTS.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
DECOMPOSITION MAY PRODUCE SMOKE, ACRID FUMES, CARBON DIOXIDE AND/OR CARBON MONOXIDE, AND POSSIBLY OTHER TOXIC VAPORS.
HAZARDOUS POLYMERIZATION:
MAY OCCUR IF EXPOSED TO ULTRAVIOLET LIGHT, SUNLIGHT, STRONG BASES, PEROXIDES, OR HIGH TEMPERATURES. UNCONTROLLED
POLYMERIZATION MAY CAUSE RAPID EVOLUTION OF HEAT AND INCREASED PRESSURE THAT COULD RESULT IN VIOLENT RUPTURE OF SEALED
CONTAINERS.
==============SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE===============
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
SPONTANEOUS POLYMERIZATION CAN OCCUR. ELIMINATE IGNITION SOURCES AND VENTILATE AREA. WEAR APPROPRIATE PROTECTIVE
EQUIPMENT INCLUDING EYE AND SKIN PROTECTION. ABSORB WITH INERT MATERIAL AND TRANSFER TO AN APPROPRIATE CONTAINER FOR
DISPOSAL. FLUSH AREA WITH WATER. PREVENT FLUSHING OR SPILLED MATERIAL FROM ENTERING WATERWAYS, INCLUDING SEWERS, STORM
DRAINS, SURFACE WATER AND SOIL.
IN THE UNITED STATES, SPILLS OR RELEASES TO THE ENVIRONMENT MAY BE REPORTABLE TO THE NATIONAL RESPONSE CENTER (1-800-
424-8802).
WASTE DISPOSAL METHOD:
DISPOSE IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL REGULATIONS. INCINERATE IN APPROVED FACILITY. DO NOT INCINERATE
CLOSED CONTAINERS.
=========================SECTION VIII - CONTROL MEASURES========================
RESPIRATORY PROTECTION:
MATERIAL SAFETY DATA SHEET
UV CURABLE CLEAR DTM COATING Page: 4
8/5/2009
IN APPLICATIONS WHERE AEROSOLS OR VAPORS ARE EMITTED, A FULL FACE ORGANIC VAPOR CARTRIDGE RESPIRATOR WITH A PARTICULATE
PRE-FILTER SHOULD BE WORN. IN CONFINED AREAS AND IN EMERGENCY SITUATIONS, USE A SELF-CONTAINED BREATHING APPARATUS OR
OTHER AIR SUPPLIED FULL FACE RESPIRATOR.
VENTILATION:
LOCAL EXHAUST IS RECOMMENDED TO CONTROL EXPOSURE WHICH MAY RESULT FROM OPERATIONS GENERATING AEROSOLS AND HOT OPERATIONS
GENERATING VAPORS. MECHANICAL EXHAUST IS NOT RECOMMENDED TO CONTROL EXPOSURE UNDER THESE CONDITIONS.
PROTECTIVE GLOVES:
IMPERVIOUS GLOVES (NEOPRENE) SHOULD BE WORN TO PROTECT AGAINST SKIN CONTACT. A COMBINATION OF BARRIER CREAM, APPLIED
BEFORE EXPOSURE, AND GLOVES IS RECOMMENDED. DO NOT APPLY CREAM AFTER EXPOSURE.
EYE PROTECTION:
IF A SPLASHING HAZARD EXISTS OR IF THERE IS POTENTIAL EYE CONTACT, WEAR SAFETY EYEWEAR SUCH AS CHEMICAL GOGGLES OR FACE
SHIELDS TO PREVENT CONTACT OF LIQUID WITH EYES. EYE FLUSHING EQUIPMENT SHOULD BE IMMEDIATELY AVAILABLE.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT:
IN SITUATIONS WHERE CONTACT CAN OCCUR, USE A FACE SHIELD, IMPERVIOUS BODY COVERING, AND BOOTS. A SAFETY SHOWER AND EYE
WASH FACILITY SHOULD BE AVAILABLE.
=======================SECTION IX - SPECIAL PRECAUTIONS=========================
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
DO NOT STORE ABOVE 100 DEG F. KEEP CONTAINERS TIGHTLY COVERED AND STORE UPRIGHT TO PREVENT LEAKAGE. DO NOT STORE OR
USE NEAR HEAT OR OPEN FLAME. AVOID PROLONGED EXPOSURE TO LIGHT.
OTHER PRECAUTIONS:
CAUTION - OSHA COMBUSTIBLE LIQUID - CLASS III B; DOT - NOT REGULATED. KEEP AWAY FROM HEAT AND FLAME. WARNING: CONTACT
WITH SKIN MAY CAUSE MODERATE SKIN INJURY SUCH AS REDDENING AND SWELLING AND SENSITIZATION. AVOID CONTACT WITH EYES,
SKIN AND CLOTHING. WEAR PROPER PROTECTIVE EQUIPMENT WHEN HANDLING OR WORKING WITH THIS MATERIAL. KEEP CONTAINER CLOSED
WHEN NOT IN USE. BREATHING OF MIST OR VAPOR FROM HEATED MATERIAL MAY BE HARMFUL. USE WITH ADEQUATE VENTILATION. WASH
THOROUGHLY AFTER HANDLING. DO NOT TAKE INTERNALLY. DO NOT SAND, FLAME CUT, BRAZE OR WELD DRY COATING WITHOUT PROPER
PROTECTIVE EQUIPMENT OR SUFFICIENT VENTILATION. FOR INDUSTRIAL USE ONLY.
SPECIAL PRECAUTIONS:
*N/A
MISCELLANEOUS PRECAUTIONS:
EMPTY CONTAINERS MAY RETAIN PRODUCT RESIDUE AND/OR VAPORS. ALWAYS OBEY HAZARDOUS WARNINGS AND HANDLE EMPTY CONTAINERS
AS IF THEY WERE FULL.
============================SECTION X - DISCLAIMER==============================
SARA 313 INFORMATION:
*N/A
FOOTNOTE:
THIS PRODUCT CONTAINS ACRYLATED EPOXY, ACRYLIC MONOMERS, AND PHOTOINITIATOR RESINS WHICH ARE NOT LISTED IN THE HAZARDOUS
INGREDIENTS OF OSHA 29CFR SECTION 1910.1200(d)(3).
MATERIAL SAFETY DATA SHEET
UV CURABLE CLEAR DTM COATING Page: 5
8/5/2009
USER'S RESPONSIBILITY: THE RESPONSIBILITY TO PROVIDE A SAFE WORKPLACE REMAINS WITH THE USER. THE USER SHOULD CONSIDER
THE HEALTH HAZARDS AND SAFETY INFORMATION CONTAINED HEREIN AS A GUIDE AND SHOULD TAKE THOSE PRECAUTIONS REQUIRED IN AN
INDIVIDUAL OPERATION TO INSTRUCT EMPLOYEES AND DEVELOP WORK PRACTICE PROCEDURES FOR A SAFE WORK ENVIRONMENT. IT IS THE
RESPONSIBILITY OF THE USER TO COMPLY WITH ALL APPLICABLE FEDERAL, STATE AND LOCAL LAWS AND REGULATIONS.
TO THE BEST OF OUR KNOWLEDGE, THE INFORMATION CONTAINED HEREIN IS ACCURATE. HOWEVER, STRATHMORE PRODUCTS, INC., ASSUMES
NO LIABILITY WHATSOEVER FOR THE ACCURACY, RELIABILITY OR COMPLETENESS OF THE INFORMATION CONTAINED HEREIN. FINAL
DETERMINATION OF SUITABILITY OF ANY MATERIAL IS THE SOLE RESPONSIBILITY OF THE USER. SINCE THE CONDITIONS OF HANDLING
AND USE ARE BEYOND OUR CONTROL, WE MAKE NO GUARANTEE OF RESULTS, AND ASSUME NO LIABILITY FOR DAMAGES INCURRED BY USE OF
THIS MATERIAL. ALL MATERIALS MAY PRESENT UNKNOWN HEALTH AND SAFETY HAZARDS AND SHOULD BE USED WITH CAUTION. ALTHOUGH
CERTAIN HAZARDS ARE DESCRIBED HEREIN, WE CANNOT GUARANTEE THAT THESE ARE THE ONLY HAZARDS WHICH EXIST.
|