Material Safety Data
SECTION I: Product and Company Identity:
TRADE NAME (AS LABELED): TS- Moly Motor Eze
MANUFACTURER'S NAME: T.S. Moly-Lubricants, Inc.
MANUFACTURER'S ADDRESS: 6205 Brookhill #6
Houston TX 77087
EMERGENCY PHONE: 713/671-2676 Fax: 713/671-9417
BUSINESS PHONE: 713/671-2676 Fax: 713/671-9417
REVIEWED: July 26, 2005
REVIEWED BY: Jo Nell Salling
SECTION II: Composition /Information on Ingredients
The criteria for listing components in the composition section are as follows: Carcinogens are listed
when present at 0.1% or greater; components which are otherwise hazardous according to OSHA
are listed when present at 1.0% or greater; nonhazardous components are not listed as being
proprietary information. Refer to Section IX for regulatory information.
OSHA PEL (mg/m3) ACGIH TLV (mg/m3)
Ingredient SARA CAS No. % Optional
monochloro toluene no 95-49-8 NDA TWA: 50 ppm; 259 ~5
toluene no 108-88-3 TWA 200 ppm * TWA: 50 ppm; 188 <0.25
petroleum oil no 8002-05-9 500 ppm; 2000 NDA proprietary
* Acceptable maximum peak above the acceptable ceiling concentration for an 8 hr shift: 500 ppm/10 min. Ceiling
SECTION III: Hazards Identification
Prolonged exposure to high vapor concentrations
HEALTH (BLUE) 1
may cause headaches and dizziness. Based on
FLAMMABILITY (RED) 1
components, extended exposure t elevated
concentrations have produced tumorgenic effects in REACTIVITY (YELLOW) 0
PROTECTIVE EQUIPMENT B
some laboratory animals.
SYMPTOMS OF OVEREXPOSURE BY ROUTE
EYES RESPIRATORY HANDS BODY
INHALATION: Vapor inhalation under ambient
conditions is normally not a problem.
SKIN: Prolonged or repeated skin contact with this
See Section 8
product tends to remove skin oils, possibly leading
to irritation and dermatitis. No chronic health problems known.
EYES: Contact with the eyes would be expected to cause irritation consisting of reversible redness,
swelling and mucous discharge to the conjunctiva.
INGESTION: Acute. Ingestion of this product may cause irritation and gastrointestinal discomfort
consisting of nausea, vomiting, lethargy and/or diarrhea. Chronic: There are no known or reported
MATERIAL SAFETY DATA SHEET
Page 2 of 3
TS- Moly Motor Eze
effects from chronic exposure except for effects similar to those experienced from a single
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None known or reported.
CARCINOGENICITY: NTP? No IARC Monographs? Group 3 (for toluene, unclassifiable as
a human carcinogen) OSHA regulated? No
In accordance with the current OSHA Hazard Communication Standard criteria, this product is not
known or reported to be carcinogenic by reference sources including: IARC, NTP, and OSHA.
SECTION IV: First Aid Measures
EYES: Flush eyes with plenty of water for several minutes. Get medical attention if eye irritation
SKIN: Remove any contaminated clothing and wash skin with plenty of soap and water for several
minutes. Get medical attention if skin irritation develops or persists. If product is injected into or
under the skin, or into any part of the body, regardless of the appearance of the wound or its size,
the individual should be evaluated immediately by a physician as a surgical emergency. Even
though initial symptoms from high pressure injection may be minimal or absent, early surgical
treatment within the first few hours may significantly reduce the ultimate extent of injury.
INGESTION: If person is conscious and can swallow, give two glasses of water but do not induce
vomiting. If vomiting occurs, give fluids again. Consult a physician if symptoms develop. DO
NOT GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
INHALATION: If overcome from vapor, remove from exposure and call physician. If necessary,
provide respiratory support.
SECTION V: Fire Fighting Measures
Flash Point: 200 癋.(based on component information) Method: PMCC Flammable Limits: NDA
Extinguishing Media: Carbon dioxide, dry chemical, alcohol foam, water spray.
Special Fire Fighting Procedures: Use water to cool containers exposed to fire. For fires in
enclosed areas, firefighters should use self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: Avoid fumes of burning product.
SECTION VI: Accidental Release Measures
CLEAN WATER ACT/OIL POLLUTION ACT: This product may be classified as an oil under
Section 311 of the Clean Water Act, and under the Oil Pollution Act. Discharges or spills into or
leading to surface waters that cause a sheen must be reported to the National Response Center
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Recover free
product. Add sand, earth, or some other suitable adsorbent. Keep product out of sewers and
watercourses by diking or impounding. Advise authorities if product has entered sewers, water
courses, or extensive land areas.
SECTION VII: Handling and Storage
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Store in cool dry area in
original or equivalent container in accordance with all applicable regulations. Do not apply high
heat or flame to container.
OTHER PRECAUTIONS: Good personal hygiene practices should always be followed.
MATERIAL SAFETY DATA SHEET
Page 3 of 3
TS- Moly Motor Eze
SECTION VIII: Exposure Controls/Personal Protection
VENTILATION AND ENGINEERING CONTROLS: Use with adequate ventilation. Use a
mechanical fan or vent area to outside if necessary. Provide ventilation sufficient to prevent
exceeding recommended exposure limit or buildup of explosive concentrations of vapor in air.
RESPIRATORY PROTECTION: Respiratory protection is not expected to be needed. If
respiratory protection is needed, use only protection authorized by applicable regulations.
EYE PROTECTION: Safety goggles recommended.
HAND PROTECTION: Wear rubber gloves for routine industrial use.
BODY PROTECTION: Use body protection as needed for task.
SECTION IX: Physical and Chemical Properties
Boiling Point: NDA Specific Gravity: 0.88
Vapor Pressure: NDA Evaporation Rate: Slower than ether
Vapor Density: lighter than air Solubility in Water: Negligible
Appearance and Odor: gray-black liquid with slight solvent odor.
SECTION X: Stability and Reactivity
STABILITY: Unstable: No Stable: Yes
CONDITIONS TO AVOID/INCOMPATIBILITY: High heat; mixing with concentrated oxidizing
or reducing agents such as peroxides, bromine, chlorine, fluorine, etc.
POLYMERIZATION: May occur: No Will not occur: Yes
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: oxides of carbon, molybdenum, sulfur,
hydrogen chloride, chlorocarbons, fumes and smoke.
SECTION XI: Toxicological Information: No data available.
SECTION XII: Ecological Information: No data available.
SECTION XIII: Disposal Considerations
WASTE DISPOSAL METHODS: Dispose of waste according to all applicable regulations.
SECTION XIV: Transport Information
This material is not regulated as a DOT hazardous material.
SECTION XV: Regulatory Information
TOXIC SUBSTANCES CONTROL ACT (TSCA): All components are on the TSCA inventory or
are not required to be listed on the TSCA inventory.
SECTION XVI: Other Information
Disclaimer: Information given herein is offered in good faith as accurate, but without guarantee. Conditions
of use and suitability of this product for particular uses are beyond our control. Users should make their own
investigation to determine the suitability of the information or products for their respective purposes.